Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manual

Moxa EtherDevice™ Switch
EDS-P506A-4PoE Series
Hardware Installation Guide
First Edition, July 2010
©2010 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802005060010

—1 —
Overview
The Moxa EtherDevice™ EDS-P506A-4PoE Series Ethernet switches are
managed redundant Ethernet switches that come standard with 4
10/100BaseT(X) 802.3at/af (PoE/PoE+) compliant Ethernet ports, and 1 or 2
10/100BaseT(X) Ethernet ports or 1 or 2 100BaseFX (SC/ST-type connector)
fiber ports. The EDS-P506A-4PoE Ethernet switches provide up to 30 watts
of power per PoE port, and allow power to be supplied to connected devices
(such as surveillance cameras, wireless access points, and IP phones) when
power is not readily available or cost-prohibitive to provide locally. The
EDS-P506A-4PoE Ethernet switches are highly versatile, and their fiber ports
can transmit data up to 40 km from the device to the control center with high
EMI immunity. The Ethernet switches support a variety of management
functions, including Turbo Chain, IEEE 1588 PTP, Turbo Ring, RSTP/STP,
IGMP, VLAN, QoS, RMON, bandwidth management, and port mirroring.
The EDS-P506A-4PoE series is designed especially for security automation
applications such as IP surveillance and gate of entry systems, which can
benefit from a scalable backbone construction and Power-over-Ethernet
support.
The EDS-P506A-4PoE can operate from 0 to 60°C or -40 to 75°C for T
models and are designed to withstand a high degree of vibration and shock.
The rugged hardware design makes the EDS-P506A-4PoE Series perfect for
ensuring that your Ethernet equipment can operate in critical industrial
environments, and complies with FCC and CE standards.
NOTE Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch.
EDS = Moxa EtherDevice Switch
Package Checklist
The EDS-P506A-4PoE is shipped with the following items. If any of these
items are missing or damaged, please contact your customer service
representative for assistance.
y1 EDS-P506A-4PoE EtherDevice Switch
yHardware Installation Guide (this guide)
yCD-ROM with user’s manual and Windows utility
yMoxa product warranty statement
yRJ45 to DB9 console port cable
yProtective caps for unused ports
yDIN-Rail mounting kit (attached to the EDS-P506A-4PoE’s rear panel by
default)

—2 —
EDS-P506A-4PoE Panel Views
(standard type)
EDS-P506-4PoE
Front Panel View
16
MSTR/
HEAD
CPLR/
TAI L
11
6
7
8
9
10
14
15
12
13
19
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
PWR1
4
3
2
1
PWR2
RELAY2
RELAY1
DI1
DI2
V2-
V2+
I1
I2
Top Panel View
1
2
3
4
1
Rear Panel View
2
18
17
5
2
17
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD LED indicator
10. CPLR/TAIL LED indicator
11. Turbo Chain logo
12. TP port’s 100 Mbps LED
13. TP port’s 10 Mbps LED
14. Model Name
15. 10/100 BaseT(X) PoE Ports
16. 10/100 BaseT(X) Ports
17. Screw hole for wall mounting
kit
18. DIN-Rail kit
19. PoE LEDs

—3 —
EDS-P506A-4PoE Panel Views
(SC-type)
EDS-P506A-4PoE-MM-SC
/
EDS-P506A-4PoE-SS-SC
Front Panel View
14
15
16
12
13
11
6
7
8
9
10
17
20
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
PWR1
43
2
1
PWR2
RELAY2
RELAY1
DI1
DI2
V2-
V2+
I1
I2
Top Panel View
1
2
3
4
5
2
1
Rear Panel View
2
19
18
18
1. Grounding screw
2. Terminal block for power
input PWR1/PWR2 and relay
output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD LED indicator
10. CPLR/TAIL LED indicator
11. Turbo Chain logo
12. TP port’s 100 Mbps LED
13. TP port’s 10 Mbps LED
14. Model Name
15. 10/100 BaseT(X) PoE Ports
16. 100BaseFX ports
17. FX port’s 100 Mbps LEDs
18. Screw hole for wall mounting
kit
19. DIN-Rail kit
20. PoE LEDs

—4 —
EDS-P506A-4PoE Panel Views
(ST-type)
EDS-P506A-4PoE-MM-ST
Front Panel View
14
15
16
12
13
11
6
7
8
9
10
17
20
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
PWR1
4
3
2
1
PWR2
RELAY2
RELAY1
DI1
DI2
V2-
V2+
I1
I2
Top Panel View
1
2
3
4
1
Rear Panel View
2
19
18
18
5
2
1. Grounding screw
2. Terminal block for power
input PWR1/PWR2 and relay
output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD LED indicator
10. CPLR/TAIL LED indicator
11. Turbo Chain logo
12. TP port’s 100 Mbps LED
13. TP port’s 10 Mbps LED
14. Model Name
15. 10/100 BaseT(X) PoE Ports
16. 100BaseFX ports
17. FX port’s 100 Mbps LEDs
18. Screw hole for wall mounting
kit
19. DIN-Rail kit
20. PoE LEDs

—5 —
Mounting Dimensions
30mm(1.18in)
9.75mm(0.38in)
15mm(0.59in)
131.5mm(5.18in) 80.05mm(3.15in)
135mm(5.31in)
70mm(2.76in)
30.5mm(1.2in)
34mm(1.34in)
51.6mm(2.03in)
48.39mm(1.9in)
67mm(2.64in)
14.6mm(0.57in) 20mm(0.79in) 36.6mm(1.44in) 29.5mm(1.16in) 20mm(0.79in) 14.3mm(0.56in)
Side View
DlN-Rail Kit
Front View
Rear View
DlN-Rail Kit
Wall Mounting Kit
Wall Mounting Kit
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the back
panel of the EDS-P506A-4PoE when you take it out of the box. If you need
to reattach the DIN-Rail attachment plate to the EDS-P506A-4PoE, make
sure the stiff metal spring is situated towards the top, as shown by the
following figures.
STEP 1—Insert the top of the
DIN-Rail into the slot just below the
stiff metal spring.
STEP 2—The DIN-Rail attachment
unit will snap into place as shown in
the following illustration.
metal
spring
DIN-Rail
metal
spring
DIN-Rail
To remove the EDS-P506A-4PoE from the DIN-Rail, simply reverse Steps 1
and 2 above.

—6 —
Wall Mounting (Optional)
For some applications, you will find it convenient to mount the Moxa
EDS-P506A-4PoE on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN-Rail
attachment plate from the rear
p
anel of the
EDS-P506A-4PoE, and then
attach the wall mount plates
with M3 screws, as shown in
the figure to the right.

STEP 2—Mounting the EDS-P506A-4PoE on the wall requires 4
screws. Use the EDS-P506A-4PoE, with wall mount plates
attached, as a guide to mark the correct locations of the 6 screws.
The heads of the screws should be less than 6.0 mm in diameter,
and the shafts should be less than 3.5 mm in diameter, as shown
in the figure to the right.
6.0 mm
3.5 mm
NOTE Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the
way—leave about 2 mm to allow
room for sliding the wall mount
p
anel between the wall and the
screws.
STEP 3—Once the screws are fixed
to the wall, insert the four screw
heads through the wide parts of the
keyhole-shaped apertures, and then
slide the EDS-P506A-4PoE
downwards, as indicated in the
figure at the right. Tighten the four
screws for more stability.
MSTR/
HEAD
CPLR/
TAIL
MSTR/
HEAD
CPLR/
TAIL

—7 —
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra-Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra-Low Voltages (SELV) in compliance with
IEC60950-1/EN60950-1.
ATTENTION
This unit is a built-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC60950-1/EN60950-1
(or similar regulation).
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Read and follow these guidelines:
yUse separate paths to route wiring for power and devices. If power wiring
and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
yYou can use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.
yYou should separate input wiring from output wiring.
yWe advise that you label the wiring to all devices in the system.

—8 —
Grounding the Moxa EDS-P506A-4PoE
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.
Wiring the Relay Contact
The EDS-P506A-4PoE has two sets of relay outputs—relay 1 and relay 2.
Each relay contact uses two contacts of the terminal block on the
EDS-P506A-4PoE’s top panel. Refer to the next section for detailed
instructions on how to connect the wires to the terminal block connector, and
how to attach the terminal block connector to the terminal block receptor.
In this section, we illustrate the meaning of the two contacts used to connect
the relay contact.
RELAY1
RELAY1
RELAY2
RELAY2
FAULT:
The two sets of relay contacts of the
6-pin terminal block connector are
used to detect user-configured
events. The two wires attached to
the fault contacts form an open
circuit when a user-configured
event is triggered. If a
user-configured event does not
occur, the fault circuit remains
closed.
Wiring the Redundant Power Inputs
The EDS-P506A-4PoE has two sets of power inputs—power input 1 and
power input 2. The top two contacts and the bottom two contacts of the 6-pin
terminal block connector on the EDS-P506A-4PoE’s top panel are used for
the two digital inputs. The top and front views of one of the terminal block
connectors are shown here.
PWR1 PWR2
V1- V1+
PWR1
V2- V2+
PWR2
V1- V1+ V2- V2+
STEP 1: Insert the
negative/positive DC wires into the
V-/V+ terminals, respectively.
STEP 2: To keep the DC wires
from pulling loose, use a small
flat-blade screwdriver to tighten the
wire-clamp screws on the front of
the terminal block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS-P506A-4PoE’s
top panel.

—9 —
Wiring the Digital Inputs
The EDS-P506A-4PoE has two sets of digital inputs, DI 1 and DI 2. Each DI
consists of two contacts of the 6-pin terminal block connector on the
EDS-P506A-4PoE’s top panel, which are used for the two DC inputs. The top
and front views of one of the terminal block connectors are shown here.
I1
D2I
I2
D1I
I1I2
D2ID1I
STEP 1: Insert the negative
(ground)/positive DI wires into the
┴/I1 terminals, respectively.
STEP 2: To keep the DI wires from
pulling loose, use a small flat-blade
screwdriver to tighten the
wire-clamp screws on the front of
the terminal block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS-P506A-4PoE’s
top panel.
Turbo Ring DIP Switch Settings
EDS-P506A-4PoE switches are plug-and-play managed redundant Ethernet
switches. The proprietary Turbo Ring protocol was developed by Moxa to
provide better network reliability and faster recovery time. Moxa Turbo Ring’s
recovery time is less than 300 ms (Turbo Ring) or 20 ms (Turbo Ring
V2) —compared to a 3- to 5-minute recovery time for commercial
switches—decreasing the possible loss caused by network failures in an
industrial setting.
There are 4 Hardware DIP Switches for Turbo Ring on the top panel of
EDS-P506A-4PoE that can help setup the Turbo Ring easily within seconds. If
you do not want to use a hardware DIP switch to setup the Turbo Ring, you can
use a web browser, telnet, or console to disable this function.
NOTE Refer to the Turbo Ring DIP Switch section and Using
Communication Redundancy section in the User’s Manual for
detailed information about the settings and usage of Turbo Ring
and Turbo Ring V2.
EDS-P506A-4PoE Series DIP Switches
2
1
------
MASTER
COUPLER
TURBO
RING
4
3
The default setting for each DIP Switch is OFF. The
following table explains the effect of setting the DIP
Switch to the ON position.