Moxa Technologies EtherDevice EDS-P510 Series Manual

Moxa EtherDevice™ Switch
EDS-P510 Series Hardware Installation Guide
First Edition, November 2008
©2008 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802005101010

—1 —
Overview
We describe two products in this manual:
The Moxa EtherDevice™ EDS-P510 Series Ethernet switches are Gigabit
managed redundant Ethernet switches that come standard with 4
10/100BaseT(X) 802.3af (PoE) compliant Ethernet ports and 3 combo
Gigabit Ethernet ports. The EDS-P510 Ethernet switches provide up to 15.4
watts of power per PoE port, and allow power to be supplied to connected
devices (such as surveillance cameras, wireless access points, and IP phones)
when AC power is not readily available or cost-prohibitive to provide locally.
The EDS-P510 Ethernet switches are highly versatile, and their SFP fiber
port can transmit data up to 80 km from the device to the control center with
high EMI immunity. The Ethernet switches support a variety of management
functions, including Turbo Ring, RSTP/STP, IGMP, VLAN, QoS, RMON,
bandwidth management, and port mirroring. The EDS-P510 series is
designed especially for security automation applications such as IP
surveillance and gate of entry systems, which can benefit from a scalable
backbone construction and Power-over-Ethernet support.
The SPL-24 plays the role of PD, and splits the data signal and power signal
that are transmitted from the PSE. The SPL-24 plays a dual role of providing
power to industrial devices, and enabling Ethernet connections.
The EDS-P510 and SPL-24 can operate from 0 to 60°C or -40 to 75°C for T
model and are designed to withstand a high degree of vibration and shock.
The rugged hardware design makes the EDS-P510 Series and SPL-24 perfect
for ensuring that your Ethernet equipment can operate in critical industrial
environments, such as in hazardous locations, and complies with FCC and CE
standards.
The installation of the EDS-P510 Series is presented on pages 8 to 14. The
installation of the SPL-24 is presented on pages 14 to 18.
NOTE Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch, and we use SPL as an
abbreviation for Moxa PoE Splitter:
EDS = Moxa EtherDevice Switch
SPL = Moxa PoE Splitter
Moxa’s PoE Solution
Power over Ethernet
Power
Legend: Ethernet
E215312
LISTED
IND.CONT. EQ.
94A0
SPL-24
AWK-1100
EDS-P510 Series
Wireless Access Point
Data on
Ethernet
Data on
Ethernet 24 VDC output
48 VDC input
DR-120-48
PWR1
PWR2
FAULT
7
6
5
4
3
2
1
G1
G2
G1
G3
G2
G3
EDS-P510
MASTER
G3
G2
G1
COUPLER
10/100/1000
7
6
5
4
3
2
1
10/100
EtherDevice Switch
Turbo
Ring
PoE

—2 —
Package Checklist
The EDS-P510 is shipped with the following items. If any of these items are
missing or damaged, please contact your customer service representative for
assistance.
y1 EDS-P510 EtherDevice Switch
yHardware Installation Guide (this guide)
yCD-ROM with user’s manual and Windows utility
yMoxa product warranty statement
yRJ45 to DB9 console port cable
yProtective caps for unused ports
yDIN-Rail mounting kit (attached to the EDS-P510’s rear panel by default)
Optional Accessories
ySFP-1GSXLC: SFP module with 1 1000BaseSX port with LC conncector
for 0.5 km transmission (standard operating temperature: 0 to 60°C)
ySFP-1GLXLC: SFP module with 1 1000BaseLX port with LC conncector
for 10 km transmission (standard operating temperature: 0 to 60°C)
ySFP-1GLHXLC: SFP module with 1 1000BaseLHX port with LC
conncector for 40 km transmission (standard operating temperature: 0 to
60°C)
ySFP-1GZXLC: SFP module with 1 1000BaseZX port with LC conncector
for 80 km transmission (standard operating temperature: 0 to 60°C)
ySFP-1G10ALC: WDM-type (BiDi) SFP module with 1 1000BaseSFP port
with LC connector for 10 km transmission; TX 1310 nm, RX 1550 nm
(standard operating temperature: 0 to 60°C)
ySFP-1G10BLC: WDM-type (BiDi) SFP module with 1 1000BaseSFP port
with LC connector for 10 km transmission; TX 1550 nm, RX 1310 nm
(standard operating temperature: 0 to 60°C)
ySFP-1G20ALC: WDM-type (BiDi) SFP module with 1 1000BaseSFP port
with LC connector for 20 km transmission; TX 1310 nm, RX 1550 nm
(standard operating temperature: 0 to 60°C)
ySFP-1G20BLC: WDM-type (BiDi) SFP module with 1 1000BaseSFP port
with LC connector for 20 km transmission; TX 1550 nm, RX 1310 nm
(standard operating temperature: 0 to 60°C)
ySFP-1G40ALC: WDM-type (BiDi) SFP module with 1 1000BaseSFP port
with LC connector for 40 km transmission; TX 1310 nm, RX 1550 nm
(standard operating temperature: 0 to 60°C)
ySFP-1G40BLC: WDM-type (BiDi) SFP module with 1 1000BaseSFP port
with LC connector for 40 km transmission; TX 1550 nm, RX 1310 nm
(standard operating temperature: 0 to 60°C)
ySFP-1GSXLC-T: SFP module with 1 1000BaseSX port with LC
conncector for 0.5 km transmission (wide operating temperature: -20 to
75°C)
ySFP-1GLXLC-T: SFP module with 1 1000BaseSX port with LC
conncector for 10 km transmission (wide operating temperature: -40 to
75°C)

—3 —
ySFP-1GLHXLC-T: SFP module with 1 1000BaseSX port with LC
conncector for 40 km transmission (wide operating temperature: -40 to
75°C)
ySFP-1GZXLC-T: SFP module with 1 1000BaseSX port with LC
conncector for 80 km transmission (wide operating temperature: -40 to
75°C)
ySFP-1G10ALC-T: WDM-type (BiDi) SFP module with 1 1000BaseSFP
port with LC connector for 10 km transmission; TX 1310 nm, RX 1550 nm
(wide operating temperature: -40 to 75°C)
ySFP-1G10BLC-T: WDM-type (BiDi) SFP module with 1 1000BaseSFP
port with LC connector for 10 km transmission; TX 1550 nm, RX 1310 nm
(wide operating temperature: -40 to 75°C)
ySFP-1G20ALC-T: WDM-type (BiDi) SFP module with 1 1000BaseSFP
port with LC connector for 20 km transmission; TX 1310 nm, RX 1550 nm
(wide operating temperature: -40 to 75°C)
ySFP-1G20BLC-T: WDM-type (BiDi) SFP module with 1 1000BaseSFP
port with LC connector for 20 km transmission; TX 1550 nm, RX 1310 nm
(wide operating temperature: -40 to 75°C)
ySFP-1G40ALC-T: WDM-type (BiDi) SFP module with 1 1000BaseSFP
port with LC connector for 40 km transmission; TX 1310 nm, RX 1550 nm
(wide operating temperature: -40 to 75°C)
ySFP-1G40BLC-T: WDM-type (BiDi) SFP module with 1 1000BaseSFP
port with LC connector for 40 km transmission; TX 1550 nm, RX 1310 nm
(wide operating temperature: -40 to 75°C)
yABC-01: Automatic Backup Configurator via RS-232 Console Port, 0 to
60°C
yDR-75-48—DIN-Rail Power Supply (48 VDC, 75W/1.6A, with 85 to 264
VAC input)
yDR-120-48—DIN-Rail Power Supply (48 VDC, 120W/2.5A, with 88 to
132 VAC/176 to 264 VAC input by switch)
yEDS-SNMP OPC Server Pro—CD with EDS-SNMP OPC Server
software and user’s manual
yWK-46—Wall Mounting Kit (will be shipped with the product)
yRK-4U—4U-high 19" rack mounting kit
Features of EDS-P510 Series
High Performance Network Switching Technology
yIEEE 802.3af Power-over-Ethernet Technology
yTurbo Ring (recovery time < 20 ms at full load) and RSTP/STP
(IEEE802.1w/D)
yIGMP snooping and GMRP for filtering multicast traffic
yPort-based VLAN, IEEE 802.1Q VLAN, and GVRP to ease network
planning
yQoS-IEEE 802.1p/1Q and TOS/DiffServ to increase determinism
yPort Trunking for optimum bandwidth utilization
yIEEE 802.1X, HTTPS, and SSH to enhance network security
ySNMPv1/v2c/v3 for different levels of network management
yRMON for efficient network monitoring and proactive capability

—4 —
yBandwidth management prevents unpredictable network status
yLock port function for blocking unauthorized access based on MAC
address
yPort mirroring for online debugging
yAutomatic warning by exception through e-mail, relay output
yDigital inputs to integrate sensors and alarms with IP networks
Industrial Grade Reliability
yPower failure, port break alarm by relay output
yRedundant dual DC power inputs
Rugged Design
yOperating temperature range from 0 to 60°C, or extended operating
temperature from -40 to 75°C for “-T” models
yIP30, rugged high-strength case
yDIN-Rail or panel mounting ability
Specifications of EDS-P510 Series
Technology
Standards IEEE 802.3af for Power-over-Ethernet,
IEEE 802.3 for 10BaseT,
IEEE 802.3u for 100BaseT(X) and 100Base FX,
IEEE 802.3ab for 1000Base(X),
IEEE 802.3z for 1000BaseSX/LX/LHX/ZX,
IEEE 802.3x for Flow Control,
IEEE 802.1D for Spanning Tree Protocol,
IEEE 802.1w for Rapid STP,
IEEE 802.1Q for VLAN Tagging,
IEEE 802.1p for Class of Service,
IEEE 802.1X for Authentication,
IEEE 802.3ad for Port Trunk with LACP
Protocols IGMPv1/v2 device, GMRP, GVRP,
SNMPv1/v2c/v3, DHCP Server/Client, DHCP
Option 82, BootP, TFTP, SNTP, SMTP, RARP,
RMON, HTTP, HTTPS, Telnet, SSH, Syslog
MIB MIB-II, Ethernet-Like MIB, P-BRIDGE MIB,
Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON
MIB Group 1, 2, 3, 9
Flow Control IEEE 802.3x flow control, back pressure flow
control
Switch Properties
Priority Queues: 4
Max. Number of
Available VLANs: 64
VLAN ID Range: VID 1 to 4094
IGMP Groups: 256

—5 —
Interface
RJ45 Ports 10/100BaseT(X) or 10/100/1000BaseT(X) auto
negotiation speed
Fiber Ports 100/1000BaseSFP slot
Console Port RS-232 (RJ45)
LED Indicators PWR1, PWR2, FAULT, 10/100M (TP port), 1000M
(Gigabit port), MASTER, COUPLER, PoE
DIP Switch Turbo Ring, Master, Coupler, Reserve
Alarm Contact Two relay outputs with current carrying capacity of
0.5A @ 48 VDC
Digital Input Two inputs with the same ground, but electrically
isolated from the electronics
• For state “1”: +13 to +30V
• For state “0”: -30 to +3V
• Max. input current: 8 mA
PoE (per port)
Max. Output Power 15.4W
Output Voltage 44 to 48.5 VDC
Max. Output Current 350 mA
Max. Overload Protection 400 mA
Power
Input Voltage 48 VDC (46 to 50 VDC), redundant dual inputs
Connection Two removable 6-pin terminal blocks
Overload Current
Protection Present
Reverse Polarity
Protection Present
Physical Characteristics
Casing IP30 protection, metal case
Dimensions (W ×H ×D) 80.2 ×135 ×105 mm (3.16 ×5.31 ×4.13 in)
Weight 1170g
Installation DIN-Rail, Wall Mounting Kit (optional kit)
Environment
Operating Temperature 0 to 60°C (32 to 140°F), standard models
-40 to 75°C (-40 to 167°F) for T. models
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity 5 to 95% (non-condensing)
Regulatory Approvals
Safety UL508 (Pending), EN60950-1 (Pending)
Hazardous Location UL/cUL Class I, Division 2, Groups A, B, C, and D
(Pending);ATEX Class I, Zone 2, Ex nC IIC
(Pending)
Maritime: DNV (Pending), GL (Pending)

—6 —
Traffic Control: NEMA TS2 (Pending)
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), Level 3
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 2
EN61000-4-5 (Surge), Level 3
EN61000-4-6 (CS), Level 3
EN61000-4-8
EN61000-4-11
Shock IEC60068-2-27
Freefall IEC60068-2-32
Vibration IEC60068-2-6
WARRANTY 5 years

—7 —
Panel Views of EDS-P510
Front Panel View
1
1
2
3
5
6
1
2
7
8
7
4
3
2
4
6
7
8
9
10
11
12
5
Top Panel View
Rear Panel View
PWR1
PWR2
FAU LT
7
6
5
4
3
2
1
G1
G2
G1
G3
G2
G3
EDS-P510
MASTER
G3
G2
G1
COUPLER
10/100/1000
7
6
5
4
3
2
1
10/100
EtherDevice Switch
Turbo
Ring
PoE
ON DIP
1234
RS-232
CONSOLE
2
DI2
1
DI1
RELAY2
V1 V2 INPUTS: 46-50 VDC
PWR2
V2+
V2-
PWR1
V1+
V1-
RELAY1
Front Panel
1. 1 to 7: 10/100BaseT(X) port
2. G1 to G3: Combo
(10/100/1000BaseT(X) or
100/1000BaseSFP slot Gigabit
port.)
3. PWR1: LED for power input 1
4. PWR2: LED for power input 2
5. Fault LED
6. Turbo Ring Logo
7. MASTER LED
8. COUPLER LED
9. G1, G2, G3 LED for
10/100/1000Mbps speed
10. Port 1 to Port 7 LED for
10/100Mbps speed
11. PoE port LED (Port 1 to Port 4)
12. Model name
Top Panel
1. Ground screw
2. RS-232 console port
3. Heat dissipation orifices
4. DIP switches for Ring Master,
Ring Coupler, and Turbo Ring
5. 6-pin terminal block for DI 1, DI
2, and PWR 2
6. 6-pin terminal block for PWR1,
Relay 1 and Relay 2
Rear Panel:
7. Screw holes for Wall Mounting
Kit
8. DIN-Rail Kit

—8 —
Mounting Dimensions (unit = mm)
EDS-P510
PoE
Side View Front ViewDIN-Rail Kit
Rear View Mounting Kit
30 13.9
15
51.3
80.2
13.9
18.2
30.5
10
13.9
7.75 7.75
10
5
66
3.5
7.5
7.5 55
105
135 35
24.339.3746.7724.56
57.05
66.8
27.2
48.3
135
9
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the back
panel of the EDS-P510 when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate to the EDS-P510, make sure the stiff
metal spring is situated towards the top, as shown by the following figures.
STEP 1—Insert the top of the
DIN-Rail into the slot just below the
stiff metal spring.
STEP 2—The DIN-Rail attachment
unit will snap into place as shown in
the following illustration.
metal
spring
DIN-Rail
metal
spring
DIN-Rail
To remove the EDS-P510 from the DIN-Rail, simply reverse Steps 1 and 2
above.

—9 —
Wall Mounting (Optional)
For some applications, you will find it convenient to mount Moxa EDS-P510
on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN-Rail
attachment plate from the rear
panel of the EDS-P510, and
then attach the wall mount
plates with M3 screws, as
shown in the figure at the
right.
Ö
STEP 2—Mounting the EDS-P510 on the wall requires 4 screws.
Use the EDS-P510, with wall mount plates attached, as a guide to
mark the correct locations of the 4 screws. The heads of the
screws should be less than 6.0 mm in diameter, and the shafts
should be less than 3.5 mm in diameter, as shown in the figure on
at right.
6.0 mm
3.5 mm
NOTE Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the
way—leave about 2 mm to allow
room for sliding the wall mount
panel between the wall and the
screws.
STEP 3—Once the screws are fixed
to the wall, insert the four screw
heads through the wide parts of the
keyhole-shaped apertures, and then
slide the EDS-P510 downwards, as
indicated in the figure at the right.
Tighten the four screws for more
stability.
PWR1
PWR2
FAULT
7
6
5
4
3
2
1
G1
G2
G1
G3
G2
G3
EDS-P510
MASTER
G3
G2
G1
COUPLER
10/100/1000
7
6
5
4
3
2
1
10/100
EtherDevice Switch
Turbo
Ring
PoE
PWR1
PWR2
FAULT
7
6
5
4
3
2
1
G1
G2
G1
G3
G2
G3
EDS-P510
MASTER
G3
G2
G1
COUPLER
10/100/1000
7
6
5
4
3
2
1
10/100
EtherDevice Switch
Turbo
Ring
PoE
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra-Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra-Low Voltages (SELV) in compliance with
IEC60950-1/EN60950-1.