Moxa Technologies AirWorks AWK-3131-RCC Series User manual

AirWorks AWK-3131-RCC User’s Manual
Second Edition, May 2014
www.moxa.com/product
© 2014 Moxa Inc. All rights reserved.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
Copyright © 2014 Moxa Inc.
Reproduction without permission is prohibited.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
www.ipc2u.ru
www.moxa.pro

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview...........................................................................................................................................1-2
Package Checklist...............................................................................................................................1-2
Product Features ................................................................................................................................1-2
Product Specifications .........................................................................................................................1-3
Functional Design ...............................................................................................................................1-5
LAN Port.....................................................................................................................................1-5
LED Indicators ............................................................................................................................1-6
Beeper.......................................................................................................................................1-7
Reset Button...............................................................................................................................1-7
Relay (Digital Output)..................................................................................................................1-7
2. Getting Started.................................................................................................................................. 2-1
First-time Installation and Configuration................................................................................................2-2
Communication Testing .......................................................................................................................2-3
Function Map .....................................................................................................................................2-5
3. Web Console Configuration ............................................................................................................... 3-1
Web Browser Configuration..................................................................................................................3-2
Overview...........................................................................................................................................3-3
Basic Settings ....................................................................................................................................3-4
System Info Settings ...................................................................................................................3-4
Network Settings.........................................................................................................................3-4
Time Settings .............................................................................................................................3-5
Wireless Settings................................................................................................................................3-6
Operation Mode..................................................................................................................................3-7
Basic Wireless Settings........................................................................................................................3-7
WLAN Security Settings.............................................................................................................. 3-11
Advanced Wireless Settings........................................................................................................3-17
WLAN Certification Settings (for EAP-TLS in Client/Slave mode only) ...............................................3-20
Advanced Settings ............................................................................................................................3-21
Using Virtual LAN ......................................................................................................................3-21
Configuring Virtual LAN..............................................................................................................3-22
DHCP Server (for AP mode only) .................................................................................................3-23
Packet Filters............................................................................................................................ 3-24
RSTP Settings (for AP/Master/ACC mode only)..............................................................................3-26
SNMP Agent.............................................................................................................................. 3-28
Link Fault Pass-Through (for Client/Slave mode only) ....................................................................3-30
Auto Warning Settings.......................................................................................................................3-30
System Log ..............................................................................................................................3-31
Syslog .....................................................................................................................................3-32
E-mail......................................................................................................................................3-33
Relay....................................................................................................................................... 3-34
Trap ........................................................................................................................................3-35
Status .............................................................................................................................................3-36
Wireless Status.........................................................................................................................3-36
Associated Client List (for AP/Master/ACC mode only)....................................................................3-36
DHCP Client List (for AP mode only).............................................................................................3-37
System Log ..............................................................................................................................3-37
Relay Status.............................................................................................................................3-38
DI and Power Status.................................................................................................................. 3-38
RSTP Status .............................................................................................................................3-38
Maintenance ....................................................................................................................................3-39
Console Settings .......................................................................................................................3-39
Ping.........................................................................................................................................3-39
Firmware Upgrade.....................................................................................................................3-40
Config Import Export .................................................................................................................3-40
Load Factory Default..................................................................................................................3-41
Password..................................................................................................................................3-41
Misc. Settings ...........................................................................................................................3-41
Save Configuration ...........................................................................................................................3-42
Restart............................................................................................................................................3-42
Logout.............................................................................................................................................3-43
4. Software Installation and Configuration ........................................................................................... 4-1
Overview...........................................................................................................................................4-2
AWK Search Utility..............................................................................................................................4-2
Installing AWK Search Utility ........................................................................................................4-2
Configuring AWK Search Utility .....................................................................................................4-4
5. Other Console Considerations ........................................................................................................... 5-1
www.ipc2u.ru
www.moxa.pro

RS-232 Console Configuration (115200, None, 8, 1, VT100) ....................................................................5-2
Configuration by Telnet and SSH Consoles.............................................................................................5-3
Configuration by Web Browser with HTTPS/SSL......................................................................................5-4
Disabling Telnet and Browser Access.....................................................................................................5-5
A. References ........................................................................................................................................ A-1
Beacon..............................................................................................................................................A-2
DTIM.................................................................................................................................................A-2
Fragment...........................................................................................................................................A-2
RTS Threshold....................................................................................................................................A-2
STP and RSTP ....................................................................................................................................A-2
The STP/RSTP Concept ................................................................................................................A-2
Differences between RSTP and STP................................................................................................A-3
B. Supporting Information .................................................................................................................... B-1
Firmware Recovery .............................................................................................................................B-2
DoC (Declaration of Conformity)...........................................................................................................B-3
Federal Communication Commission Interference Statement............................................................B-3
R&TTE Compliance Statement.......................................................................................................B-4
www.ipc2u.ru
www.moxa.pro

1
1. Introduction
The AWK-3131-RCC series are 3-in-1 industrial AP/bridge/client devices designed specifically for rail
carriage-to-carriage communication and can provide up to 300 Mbps with IEEE 802.11n technology. The new
operation mode, Auto Carriage Connection (ACC), enables automatic wireless connections between two
adjacent carriages. The AWK-3131-RCC is rated to operate at temperatures ranging from -25 to 60°C for
standard models and -40 to 75°C for wide-temperature models, and is rugged enough for any harsh industrial
environment.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Product Specifications

Functional Design
LAN Port
LED Indicators
Beeper
Reset Button
Relay (Digital Output)
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Introduction
1-2
Overview
The AWK-3131-RCC is 802.11n compliant to deliver speed, range, and reliability to support even the most
bandwidth-intensive applications. The 802.11n standard incorporates multiple technologies, including Spatial
Multiplexing MIMO (Multi-In, Multi-Out), 20 and 40 MHz channels, and dual bands (2.4 GHz and 5 GHz) to
generate lightning speeds, while still being able to communicate with legacy 802.11a/b/g devices.
The AWK-3131-RCC is compliant with EN 50155, covering operating temperature, power input voltage, surge,
ESD, and vibration. Installation of the AWK is easy using DIN-Rail mounting or distribution boxes, and with its
wide operating temperature range, IP30-rated housing with LED indicators, and DIN-Rail mounting it is a
convenient yet reliable solution for all types of industrial wireless applications.
Package Checklist
Moxa’s AWK-3131-RCC is shipped with the following items. If any of these items is missing or damaged, please
contact your customer service representative for assistance.
•1 AWK-3131-RCC
•Quick Installation Guide
•Software CD
•Moxa Product Warranty Card
•Cable holder with 1 screw
•2 plastic RJ45 protective caps for console port
•DIN rail kit
NOTE
Antennas are not included and should be purchased separately. The AWK is certified with 2dBi
omni
-directional antennas with QMA to RP-SMA adaptors.
Product Features
•Designed specifically for rail carriage-to-carriage communication
•Compliant with EN 50155
•IEEE802.11a/b/g/n compliant
•Three-in-one design (AP/Bridge/Client)
•Advanced wireless security
64-bit and 128-bit WEP/WPA/WPA2
SSID Hiding/IEEE 802.1X/RADIUS
Packet access control & filtering
•STP/RSTP support for network system redundancy
•Long-distance transmission support
•Turbo Roaming enables rapid handover (Client mode)
•ABC-01 for configuration import/export
•RS-232 console management
•2DI+1DO for on-site monitoring and warnings
•Wide -40 to 75°C operating temperature range (-T model)
•Redundant 24 VDC power inputs or IEEE802.3af Power over Ethernet
•DIN-Rail or wall mounting
•IP30 protected high-strength metal housing
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Introduction
1-3
Product Specifications
WLAN Interface
Standards:
IEEE 802.11a/b/g/n for Wireless LAN
IEEE 802.11i for Wireless Security
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseTX
IEEE 802.3ab for 1000BaseT
IEEE 802.3af for Power
-over-Ethernet
IEEE 802.1D for
Spanning Tree Protocol
IEEE 802.1w for Rapid STP
IEEE 802.1Q VLAN
Spread Spectrum and Modulation (typical):
• DSSS with DBPSK, DQPSK, CCK
• OFDM with BPSK, QPSK, 16QAM, 64QAM
• 802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps,
DBPSK @ 11 Mbps
• 802.11a/g:
64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps,
QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps
• 802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates supported)
Operating Channels (central frequency):
US:
2.412 to 2.462 GHz (11 channels)
5.18 to 5.24 GHz (4 channels)
EU:
2.412 to 2.472 GHz (13 channels)
5.18 to 5.24 GHz (4 channels)
Security:
• SSID broadcast enable/disable
• Firewall for MAC/IP/Protocol/Port
-based filtering
• 64
-bit and 128-bit WEP encryption, WPA /WPA2-Personal and En
terprise (IEEE 802.1X/RADIUS, TKIP and
AES)
Transmission Rates:
802.11b: 1, 2, 5.5, 11
Mbps
802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
Mbps
802.11n: 6 to 300 Mbps (multiple rates supported)
TX Transmit Power:
802.11b:
1 to 11 Mbps: Typ. 18 dBm (± 1.5 dBm)
802.11g:
6 to 24 Mbps: Typ. 18 dBm (± 1.5 dBm)
36 to 48 Mbps: Typ. 17 dBm (± 1.5 dBm)
54 Mbps: Typ. 15 dBm (± 1.5 dBm)
802.11a:
6 to 24 Mbps: Typ. 17 dBm (± 1.5 dBm)
36 to 48 Mbps: Typ. 16 dBm (± 1.5 dBm)
54 Mbps: Typ. 14 dBm (± 1.5 dBm)
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Introduction
1-4
TX Transmit Power
MIMO:
802.11a/n (20/40 MHz):
MCS15 20 MHz: Typ. 13 dBm (± 1.5 dBm)
MCS15 40 MHz: Typ. 12 dBm (± 1.5 dBm)
802.11g/n (20/40 MHz):
MCS15 20 MHz: Typ. 14 dBm (± 1.5 dBm)
MCS15 40 MHz: Typ. 13 dBm (±
-1.5 dBm)
RX Sensitivity:
802.11b:
-
92 dBm @ 1 Mbps, -90 dBm @ 2 Mbps, -88 dBm @ 5.5 Mbps, -84 dBm @ 11 Mbps
802.11g:
-
87 dBm @ 6 Mbps, -86 dBm @ 9 Mbps, -85 dBm @ 12 Mbps, -82 dBm @ 18 Mbps, -80 dBm @ 24 Mbps, -
76
dBm @ 36 Mbps,
-72 dBm @ 48 Mbps, -70 dBm @ 54 Mbps
802.11a:
-
87 dBm @ 6 Mbps, -86 dBm @ 9 Mbps, -85 dBm @ 12 Mbps, -82 dBm @ 18 Mbps,
-
80 dBm @ 24 Mbps, -76 dBm @ 36 Mbps, -72 dBm @ 48 Mbps, -70 dBm @ 54 Mbps
RX Sensitivity MIMO:
802.11a/n:
-
68 dBm @ MCS15 40 MHz, -70 dBm @ MCS7 40 MHz, -69 dBm @ MCS15 20 MHz, -
71 dBm @ MCS7 20 MHz
802.11g/n:
-
68 dBm @ MCS15 40 MHz, -70 dBm @ MCS7 40 MHz, -69 dBm @ MCS15 20 MHz,
-
71 dBm @ MCS7 20 MHz
Protocol Support
General Protocols:
Proxy ARP, DNS, HTTP, HTTPS, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, PPPoE, DHCP
AP
-only Protocols: ARP, BOOTP, DHCP, STP/RSTP (IEEE 802.1D/w)
Interface
Connector for External Antennas:
AWK-3131-M12-RCC: QMA (female)
M12
Ports: 1, 10/100/1000BaseT(X), auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X
connection
Console Port:
RS-232 (RJ45-type)
LED Indicators:
PWR1, PWR2, PoE, FAULT, STATE, signal strength, WLAN, LAN
Alarm Contact (Digital Output):
1 relay output with current carrying capacity of 1 A @ 24 VDC
Digital Inputs:
2 electrically isolated inputs
• +13 to +30 V for
state “1”
• +3 to
-30 V for state “0”
• Max. input current: 8 mA
Physical Characteristics
Housing: Metal, IP30 protection
Weight:
970 g
Dimensions:
53.6 x 135 x 105 mm (2.11 x 5.31 x 4.13 in)
Installation:
DIN-Rail mounting (standard), wall mounting (optional)
Environmental Limits
Operating Temperature:
Standard Models:
-20 to 60°C (-13 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient
Relative Humidity: 5% to 95% (non-condensing)
Power Requirements
Input Voltage:
12 to 48 VDC, redundant dual DC power inputs or 48 VDC Power-over-
Ethernet (IEEE 802.3af
compliant)
Connector:
10-pin removable terminal block
Power Consumption:
12 to 48 VDC, 700 mA
Reverse Polarity Protection:
Present
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Introduction
1-5
Standards and Certifications
Safety:
UL 60950-1, EN 60950-1
EMC:
EN 301 489-1/17, FCC Part 15 Subpart B Class B, EN 55022/55024
Radio:
EN 300 328, EN 301 893
Rail Traffic:
EN 50155, EN 50121-1/4
Note: Please check Moxa’s website for the most up
-to-date certification status.
Warranty
MTBF (mean time between failures):
Awk-3131-M12: 407,416 hrs
Warranty Period:
5 years
Details:
See www.moxa.com/warranty
ATTENTION
•
The AWK-3131-RCC
is NOT a portable mobile device and should be located at least 20 cm away from the
human body.
•
The AWK-3131-RCC is NOT designed for the general public. A well-trained technician should be enlisted t
o
ensure safe deployment of AWK-3131-RCC units, and to establish a wireless network.
Functional Design
LAN Port
The AWK-3131-RCC comes standard with 1 M12 Gigabit port. The LAN LED will light up when the LAN cable is
inserted.
ATTENTION
Do not use the PoE Injector. Instead, use an IEEE 802.3af or IEEE 802.3at compliant PSE (Power Sourcing
Equipment) for the PoE (Power over Ethernet) device.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Introduction
1-6
LED Indicators
The LEDs on the front panel of the AWK-3131-RCC provide a quick and easy means of determining the current
operational status and wireless settings.
The FAULT LED indicates system failures and user-configured events. If the AWK-3131-RCC cannot retrieve
the IP address from a DHCP server, the FAULT LED will blink at one second intervals. The SIGNAL LEDs
indicate signal strength, and only operate in Client mode.
The following table summarizes how to read the device’s wireless settings from the LED displays. More
information is available in Chapter 3 in the “Basic Wireless Settings” section.
LED Color State Description
PWR1 Green ON Power is being supplied from power input 1
OFF Power is not being supplied from power input 1
PWR2 Green
ON
Power is being supplied from power input 2
OFF Power is not being supplied from power input 2
PoE Amber ON Power is being supplied via PoE
OFF Power is not being supplied via PoE
FAULT Red
Blinking (slow) Cannot get an IP address from the DHCPserver (interval: 1
sec)
Blinking (fast) IP address conflict (interval: 0.5 sec)
Off Error condition does not exist
STATE Green/
Red
Green Software ready
Green,
Blinking The AWK has been located by the AWK STATE Green/Red Search Utility (interval: 1 sec)
Red Booting error condition
SIGNAL On
(5 LEDs) Green ON Signal level (for Client/Slave mode only)
OFF
WLAN Green/
Amber
Green On WLAN functions in Client/Slave/ACC mode
Green, Blinking WLAN’s data communication is run in Client/Slave/ACC mode
Amber On WLAN functions in AP/Master/ACC mode
Amber, Blinking WLAN’s data communication is run in AP/Master/ACC mode
Off WLAN is not in use or not working properly
LAN Green/
Amber
Amber LAN port’s 10/100 Mbps link is active.
Amber, Blinking
Data is being transmitted at 10/100 Mbps
Amber Off LAN port’s 10/100 Mbps link is inactive
Green LAN port’s 1000 Mbps link is active.
Green, Blinking Data is being transmitted at 1000 Mbps
Green Off LAN port’s 1000 Mbps link is inactive
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Introduction
1-7
ATTENTION
When
the system fails to boot, the LEDs for STATE (Green), FAULT, and WLAN will all light up
simultaneously and blink at one
-
second intervals. This may be due to improper operation or uncontrollable
issues, such as an unexpected shutdown
while updating the firmware. To recover the firmware, refer to
the
“Firmware Recovery”
section in Chapter 6.
Beeper
The beeper emits two short beeps when the system is ready.
Reset Button
The RESET button is located on the top panel of the AWK-3131-RCC. You can reboot the AWK-3131-RCC or
reset it to factory default settings by pressing the RESET button with a pointed object such as an unfolded
paper clip.
•System reboot: Hold the RESET button down for under 5 seconds and then release.
•Reset to factory default: Hold the RESET button down for over 5 seconds until the STATE LED starts
blinking green. Release the button to reset the AWK-3131-RCC.
Relay (Digital Output)
The AWK-3131-RCC has one relay output consisting of the 2 terminal block contacts on the top panel, as shown
below. These relay contacts are used to forward system failures and user-configured events.
The two wires attached to the relay contacts form an open circuit when a user-configured event is triggered. If
a user-configured event does not occur, the relay circuit will remain closed. For safety reasons, the relay circuit
is kept open when the AWK-3131-RCC is not powered up.
Summary of the AWK-3131-RCC’s Relay Status
Power Status Event Relay
Off – Open
On Yes Open
No Short
www.ipc2u.ru
www.moxa.pro

2
2. Getting Started
This chapter explains how to install Moxa’s AirWorks AWK-3131-RCC for the first time, and quickly set up your
wireless network and test whether the connection is running well. The Function Map discussed in the third
section provides a convenient means of determining which functions you need to use.
The following topics are covered in this chapter:

First-time Installation and Configuration

Communication Testing

Function Map
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Getting Started
2-2
First-time Installation and Configuration
Before installing the AWK-3131-RCC, make sure that all items in the Package Checklist are in the box. You will
need access to a notebook computer or PC equipped with an Ethernet port. The AWK-3131-RCC has a default
IP address that must be used when connecting to the device for the first time.
•Step 1: Select the power source.
The AWK-3131-RCC can be powered by a DC power input or PoE (Power over Ethernet). The
AWK-3131-RCC will use whichever power source you choose.
•Step 2: Connect the AWK-3131-RCC to a notebook or PC.
Since the AWK-3131-RCC supports MDI/MDI-X auto-sensing, you can use either a straight-through cable or
crossover cable to connect the AWK-3131-RCC to a computer. The LED indicator on the AWK-3131-RCC’s
LAN port will light up when a connection is established.
•Step 3: Set up the computer’s IP address.
Choose an IP address on the same subnet as the AWK-3131-RCC. Since the AWK-3131-RCC’s default IP
address is 192.168.127.253, and the subnet mask is 255.255.255.0, you should set the IP address of
the computer to 192.168.127.xxx.
NOTE
After you
select Maintenance Load Factory Default and click the Submit button, the AWK-3131-RCC
will be reset to
factory default settings and the IP address will be reset to 192.168.127.253.
•Step 4: Use the web-based manager to configure the AWK-3131-RCC
Open your computer’s web browser and type http://192.168.127.253 in the address field to access the
homepage of the web-based Network Manager. Before the homepage opens, you will need to enter the user
name and password as shown in the following figure. For first-time configuration, enter the default user
name and password and then click on the Login button:
NOTE
Default user name and password:
User Name: admin
Password: root
For security reasons, we strongly recommend changing the defa
ult password. To do so, select
Maintenance

Password, and then follow the on-screen instructions to change the password.
NOTE
After you click
Submit to apply changes the web page will refresh (Updated) will appear on the page
and a
blinking reminder will be shown on the upper
-right corner of the web page:
To
activate the changes click Restart and then Save and Restart
after you change the settings. About 30
seconds are needed for the
AWK-3131-RCC to complete the reboot procedure.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Getting Started
2-3
•Step 5: Select the AWK-3131-RCC operation mode.
By default, the AWK-3131-RCC’s operation mode is set to AP. You can change to Client mode in Wireless
Settings Basic Wireless Settings. Detailed information about configuring the AWK-3131-RCC’s
operation can be found in Chapter 3.
•Step 6: Test communications.
In the following sections we describe two test methods that can be used to ensure that a network
connection has been established.
Communication Testing
After installing the AWK-3131-RCC you can run a sample test to make sure the AWK-3131-RCC and wireless
connection are functioning normally. Two testing methods are described below. Use the first method if you are
using only one AWK-3131-RCC device, and use the second method if you are using two or more
AWK-3131-RCC units.
How to Test One AWK-3131-RCC
If you are only using one AWK-3131-RCC, you will need a second notebook computer equipped with a WLAN
card. Configure the WLAN card to connect to the AWK-3131-RCC (NOTE: the default SSID is MOXA), and
change the IP address of the second notebook (Notebook B) so that it is on the same subnet as the first
notebook (Notebook A), which is connected to the AWK-3131-RCC.
After configuring the WLAN card, establish a wireless connection with the AWK-3131-RCC and open a DOS
window on Notebook B. At the prompt, type
ping <IP address of notebook A>
and then press Enter (see the figure below). A “Reply from IP address …” response means the communication
was successful. A “Request timed out.” response means the communication failed. In this case, recheck the
configuration to make sure the connections are correct.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Getting Started
2-4
How to Test Two or More AWK-3131-RCC Units
If you have two or more AWK-3131-RCC units, you will need a second notebook computer (Notebook B)
equipped with an Ethernet port. Use the default settings for the first AWK-3131-RCC connected to notebook A
and change the second or third AWK-3131-RCC connected to notebook B to Client mode, and then configure
the notebooks and AWK-3131-RCC units properly.
After setting up the testing environment, open a DOS window on notebook B. At the prompt, type:
ping <IP address of notebook A>
and then press Enter. A “Reply from IP address …” response means the communication was successful. A
“Request timed out” response means the communication failed. In this case, recheck the configuration to make
sure the connections are correct.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Getting Started
2-5
Function Map
Basic settings for administering the AWK-3131-RCC
Essential settings related to establishing a
wireless network
Advanced features to support additional network
management and secure wired and wireless
communication
Note: These advanced functions are all optional
Application-oriented device
management functions to set up
events, traps,
and reactions via relay
warning, e-mail, and SNMP
notification
Note: These functions are all optional
Current status information for monitoring
wired/wireless network performance, advanced
services, and device management functions
Functions for maintaining the AWK-3131-RCC,
and for diagnosing the network
On-demand functions to support the web-
based
console management operation
Quick overview of the AWK-3131-RCC’s status
www.ipc2u.ru
www.moxa.pro

3
3. Web Console Configuration
In this chapter, we explain all aspects of web-based console configuration. Moxa’s easy-to-use management
functions help you set up your AWK-3131-RCC and make it easy to establish and maintain your wireless
network.
The following topics are covered in this chapter:

Web Browser Configuration

Overview

Basic Settings
System Info Settings
Network Settings
Time Settings

Wireless Settings

Operation Mode

Basic Wireless Settings
WLAN Security Settings
Advanced Wireless Settings
WLAN Certification Settings (for EAP-TLS in
Client/Slave mode only)

Advanced Settings
Using Virtual LAN
Configuring Virtual LAN
DHCP Server (for AP mode only)
Packet Filters
RSTP Settings (for AP/Master/Slave/ACC
modes only)
SNMP Agent
Link Fault Pass-Through

Auto Warning Settings
System Log
Syslog
E-mail
Relay
Trap

Status
Wireless Status
Associated Client List (for AP/Master mode
only)
DHCP Client List (for AP mode only)
System Log
Relay StatusDI and Power Status
RSTP Status

Maintenance
Console Settings
Ping
Firmware Upgrade
Config Import Export
Load Factory Default
Password
Misc. Settings

Save Configuration

Restart

Logout
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Web Console Configuration
3-2
Web Browser Configuration
Moxa AWK-3131-RCC’s web browser interface provides a convenient way to modify its configuration and
access the built-in monitoring and network administration functions. The recommended web browser is
Microsoft®Internet Explorer 7.0 or 8.0 with JVM (Java Virtual Machine) installed.
NOTE
To use
the AWK-3131-RCC’s management and monitoring functions from a
PC host connected to the same
LAN as
the AWK-3131-RCC, you must make sure that the PC host and the AWK-3131-RCC
are on the same
logical subnet. Similarly, if
the AWK-3131-RCC is configured for other VLAN settings, you must make sure
your PC host is on the
management VLAN.
The Moxa
AWK-3131-RCC’s default IP is 192.168.127.253.
Follow these steps to access the AWK-3131-RCC’s web-based console management interface.
1. Open your web browser (e.g., Internet Explorer) and type the AWK-3131-RCC’s IP address in the address
field. Press Enter to establish the connection.
2. The Web Console Login page will open. Enter the password (default Username = admin; default Password
= root) and then click Login to continue.
3. You may need to wait a few moments for the web page to download to your computer. Note that the Model
name and IP address of your AWK-3131-RCC are both shown in the title bar of the web page. This
information can be used to help you identify multiple AWK-3131-RCC units.
4. Use the menu tree on the left side of the window to open the function pages to access each of the
AWK-3131-RCC’s functions.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Web Console Configuration
3-3
In the following paragraphs, we describe each AWK-3131-RCC management function in detail. A quick
overview is available in this manual in the “Function Map” section of Chapter 2.
NOTE
The model name of
the AWK-3131-RCC is shown as AWK-3131-RCC-XX,
where XX indicates the country code.
The country code
indicates the AWK-3131-RCC version and which bandwidth it uses. We use
AWK
-3131-RCC-US as an example in the following figures. (The country code and model name
that appears
on
your computer screen may be different than the one shown here.)
Overview
The Overview page summarizes the AWK-3131-RCC’s current status. The information is categorized into
several groups: System info, Device info, and 802.11 info.
Click on SSID for more detailed 802.11 information, as shown in the following figure.
NOTE
The
802.11 info that is displayed may be different for different operation modes. For example, “Current
BSSID
” is not available in Client mode, and “Signal strength” is not available in AP mode.
www.ipc2u.ru
www.moxa.pro

AirWorks AWK-3131-RCC Web Console Configuration
3-4
Basic Settings
The Basic Settings group includes the most commonly used settings required by administrators to maintain and
control the AWK-3131-RCC.
System Info Settings
The System Info items, especially Device name and Device description, are displayed and included on the
Overview page, in SNMP information, and in alarm emails. Setting System Info items makes it easier to
identify the different AWK-3131-RCC units connected to your network.
Device name
Setting Description Factory Default
Max. 31 of characters This option is useful for specifying the role or application of
different AWK-3131-RCC units. AWK-3131-RCC_< Serial No. of this
AWK-3131-RCC>
Device location
Setting Description Factory Default
Max. of 31 characters Specifies the location of different AWK-3131-RCC units. None
Device description
Setting Description Factory Default
Max. of 31 characters Use this space to record a more detailed description of the
AWK-3131-RCC None
Device contact information
Setting Description Factory Default
Max. of 31 characters Provides
information about whom to contact in order to resolve
problems. Use this space to record contact information of the
person responsible for maintaining this AWK-3131-RCC.
None
Network Settings
The Network Settings configuration panel allows you to modify the usual TCP/IP network parameters. An
explanation of each configuration item is given below.
www.ipc2u.ru
www.moxa.pro