MPK VisionVent S pro User manual

1 Issue 01.2021
MPK Metall- und
Plastikverarbeitung GmbH & Co. KG
Friedrich-Ebert-Str. 298-300
D-58566 Kierspe
mpk-kierspe.de
Rooflight with pleated blind and net
for installation in caravans and mobile homes
VisionVent S pro
Technical data:
EN Installation and Operating Instructions
Please read the instructions carefully before installing the rooflight and store
it for future.
We cannot be held responsible for incorrect fitting, handling or operation.
Any product faults relating to the production and materials used should be notified to us via
an authorised dealer immediately.
Included with delivery
1x Rooflight with outer frame
1x Installation frame
1x Inner frame with double pleats
Additionally required for installation (not included in delivery)
1x Elastic sealant adhesive, e.g. Dekalin Dekaseal 8936 or SikaLastomer®-710
8x Fixing screws for the upper frame
Pan 3,5 mm / head according to DIN ISO 7049 (DIN 7981) /
The length of the screw should be determined by the roof thickness,
plus approximately 10 mm for the screw to enter the upper frame.
Explanation of symbols
Safety and installation instructions
Check the roof thickness of your vehicle before mounting.
The rooflight should only be fitted to a flat roof surface, both internally and
externally.
Choose a fitting position that will not interfere with other roof mounted components
(e.g. roof-racks/antenna's etc.) and avoid internally installed electrical cables and
furniture, which could impede the correct operation of the rooflight.
Never stand on the dome of the rooflight!
Do not open the rooflight while driving. The rooflight must be locked down before
traveling.
Do not open the rooflight in strong wind or rain .
Close the rooflight during rain and snowfall.
Extras (optional)
Designation
Article No.
Adapter frame for Fiat Ducato
2828ARW
Aperture
280 x 280 mm
Roof thickness
24-46 bzw. 42-72 mm
Corner radius
18 mm
Site dome
380 x 395 mm
Height over roof
80 mm
Ventilation
75 cm²
Weight
1,7 kg
Size inner frame
340 x 365 x 32 mm
Outer frame material
Polypropylene
Dome material
PC + Polypropylene
Speed limit
130 km/h
Authorization
ECE R43 -019652
NOTE
Particulary important information.
ATTENTION!
Failure to observe can lead to material damage.
WARNING!
Safety note: Serious risk of injury.

2 Issue 01.2021
Installation
Please clean the frames carefully before mounting the
sealant.
Follow the instructions of the sealant manufacturer.
Separate the inner and outer frames and fit the outer frame
to the outside of the roof aperture onto a bed of sealant.
The operating handles facing the front and rear of the
vehicle!
Correctly align the upper frame and the installation frame and
secure evenly with the screws.
Max. Torque 0.5 Nm.
Make sure that the recesses of the mounting frame are on the
sides of the handles.
Correctly position the plissé frame to the inner mounting frame
and clip it into place. Special centring devices will help to find
the right position.
Operation
To open the rooflight, press both locking buttons and push the handles upwards.
The rooflight can be opened fully by the handles or in four different directions, so that the
dome can be angled against driving weather conditions.
To close the rooflight, press the locking buttons again and pull the handles down. The roof
hood is locked.
Keep the pleated blinds open while driving to avoid driving noise and damage
from the airstream.
To avoid heat accumulation do not close blind completely during the day. Open
both pleats when not using the vehicle.
Cleaning
Dome For easier cleaning of the dome it can be removed from the frame
by releasing the four screws holding the handle arms.
Never remove the screws holding the dome and the
handles together. These are secured by a torque
screwdriver and should only be handled by an approved
dealer.
Use only clear water and a soft sponge.
Solvents may attack the plastic and make it brittle.
Clean the gaps by immersing the hood in a container filled with
water. Let the dirt soak a little.
Use the two handles to pull the hood through the water so that the
dirt can be washed out.
Make sure that only the original screws are used when
replacing the dome and they enter the thread in the plastic
correctly. Do not over-tighten.
Pleated frame Release the 4 fixing clips with a screw driver to remove the frame.
Please release carefully to not damage the clips.
Clean the pleated blinds with a soft brush, dry cloth or feather
duster.
We strongly advise against wet cleaning, as this can
damage the insect screen and blackout pleated blind.
Warranty
The legal warranty applies.
mpk-kierspe.de/Downloads