MRHANDSFREE BLUE PERFECTION User manual

m_BluePerfection_Cover.pmd 03.02.2006, 17:31
1

M_Blue_Perfect_Illystr.pmd 26.05.2005, 14:13
1

TABLE OF CONTENTS
SAFETYINSTRUCTIONS .................................................................................... 2
WHATDOESMRHANDSFREEBLUEPERFECTIONINCLUDE? .......................... 2
DESCRIPTION ................................................................................................... 3
INSTALLATION .................................................................................................. 6
OPERATION....................................................................................................... 10
TROUBLE-SHOOTING ....................................................................................... 23
TECHNICALPARAMETERS ................................................................................ 24
BLUETOOTH®.................................................................................................... 25
CAREANDTECHNICALMAINTENANCE ............................................................. 25
m_BluePerfection_GB.pmd 10.02.2006, 15:171

...........................................................................................................................................................................
GB - 2
SAFETYINSTRUCTIONS
1. Before starting the installation, make sure that the car ignition is off.
2. Make sure that the operation of the carkit will never influence your safety.
3. Make sure not to damage electrical cables, fuel or brake lines or safety equipment during the installation.
4. Make sure not to impact the steering or braking system or other key systems essential for the proper operation of
the car when installing the carkit. Make sure that the deployment of the airbags is not blocked or impaired in any
way.
5. The carkit may only be used at an operating voltage of 12V with the minus pole earthed. Failure to observe this
requirement may result in damage to the car’s electronics system.
6. Do not operate your carkit off the car battery for a long time, i.e. with the engine switched off, as this may cause your
battery to be empty.
WHAT DOES MR HANDSFREE BLUE PERFECTION INCLUDE?
1. Handsfree unit with built-in speaker (SM1)
2. Bracket of the handsfree unit
3. Screen (D1)
4. Bracket for the screen with system cord (SC1)
5. Angle bracket for fixation of the screen to vertical surfaces
6. Infrared remote control (J1)
7. Lithium battery for Infrared remote control, CR2032, 3B
8. Set of decorative inlays for the infrared remote control – 3 pcs.
9. Microphone (M1)
10. System cable with adapter for connecting the handsfree unit to the power supply of the car, the ignition system and
to mute the radio (SC2)
11. Adapter for connecting the handsfree unit to the power supply of the car via the cigarette lighter (SC3). It includes a
changeable fuse and coil cord.
12. Fixing plates for the brackets of the screen and the handsfree unit – 2 pcs.
13. Contact clips for connecting the cables – 5 pcs.
14. Clips for guiding the microphone cable – 4 pcs.
15. Set of screws
16. Double sided tape plate - 2 pcs.
17. Screw driver
18. User’s manual
m_BluePerfection_GB.pmd 10.02.2006, 15:172

...............................................................................................................................................................................
GB - 3
DESCRIPTION
HANDSFREEUNIT (SM1)
The handsfree unit includes built-in speaker, echo canceller, noise suppressor and Bluetooth®wireless technology,
which provides a wireless connection with Bluetooth®mobile phones.
Since devices with Bluetooth®technology communicate through radio waves, your carkit and your mobile phone do not
need to be in direct line-of-sight. The 2 devices only need to be within a maximum of 10 meters of each other, so you
do not need to take your phone out of your pocket or bag to make and receive calls via the carkit.
Since Bluetooth®phones produced by different manufacturers provide various functionalities, some functions described
in this user’s manual could be different or may not be available.
The handsfree unit has the following jacks for connecting external units:
1. Socket for system cable SC1.
2. Socket for cables SC2 and SC3.
3. Socket for external speaker (Use this only with mr Handsfree original accessories).
4. Microphone socket M1.
m_BluePerfection_GB.pmd 10.02.2006, 15:17
3

...........................................................................................................................................................................
GB - 4
SCREEN(D1)
The screen unit includes:
1. LCD with big symbols and icons.
2. Convenient adjustable fixation system which allows you to choose the best viewing position of the LCD and
to release the unit easily from the dashboard to avoid theft.
3. Automatic backlight with variable light colors, contrast and brightness settings.
4. Infrared receiver for the infrared remote control.
REMOTECONTROL (J1)
The remote control should be fixed on the steering wheel. It has 2 buttons and a directional joystick. The remote
control and its functionality are developed to make access to your mobile phone as easy and clear as possible. The
connection between the remote control and the receiver in the screen unit is performed through an infrared channel.
The remote control could be fixed on the left or right side of the steering wheel (See chapter “Installation”).
Lens of infrared receiver
If press:
- Receiving a call.
- Connecting with paired phone
in Handsfree or Headset profile.
If press and hold:
- Switching on paring mode.
If press:
- Ending a call.
- Returning to the previous
level of the menu.
- Deleting input data.
If press and hold:
- Returning to Stand-by mode.
m_BluePerfection_GB.pmd 10.02.2006, 15:17
4

m_BluePerfection_RU.pmd 08.02.2006, 17:06
8
...............................................................................................................................................................................
GB - 5
MICROPHONE(M1)
The microphone is developed especially for in-car usage. The location of the microphone significantly influences the
acoustic quality (For a recommendation on locating the microphone, see the “Installation” chapter).
The microphone has a 2 positional button for adjusting its sensitivity. Press the button on the microphone to increase
the volume to the other caller.
BRACKET FOR SCREEN UNIT WITH SYSTEM CORD SC1
The bracket for the screen unit can be fixed using the fixing wheel (1). The bracket allows you to adjust vertical and
horizontal angles of the screen to achieve its best view. On the back side of the bracket there is a button (2) for
releasing the screen.
If press Up, Down,
Left or Right button:
- Navigation in the Menu.
If press and hold Up, Down,
Left or Right button:
- Quick scrolling of lists.
If press Central button:
- Opening the Menu.
- OK button.
If press:
- Ending a call.
- Returning to the previous level
of the menu.
- Deleting of input data.
If press and hold:
- Returning to Stand-by mode.
If press:
- Receiving a call.

...........................................................................................................................................................................
GB - 6
SYSTEM CABLES SC2 AND SC3
The system cable SC2 connects the handsfree unit with the power supply and the ignition system and is used for
muting the radio. The system cable SC3 is used for plug & play installation. It provides power supply via the cigarette
lighter.
Both system cables are supplied with changeable fuses. How to change the fuses is described in the picture below.
INSTALLATION
HANDSFREEUNIT (SM1)
We recommend mounting the handsfree unit at a less visible position in the car. However, make sure that the unit can
provide good acoustic, by directing the speaker towards the user and by placing the unit at a distance of more than 1 meter
from the microphone.
Search for a location in your car where the handsfree unit fits and where it is comfortable for use. Make sure that the location
in your car where you would like to install your handsfree unit is free from dust and dirt.
The bracket for the handsfree unit should be installed so that the handsfree unit slides into place and could be easily
removed if necessary.
The bracket can be fixed in 2 ways:
1. Immediately to the dashboard or to any other place in the car using the installation screws.
2. To the fixing plate using the installation screws. The fixing plate should then be fixed to the dashboard or to any
other place in the car by means of the double sided tape plate.
m_BluePerfection_GB.pmd 10.02.2006, 15:176

...............................................................................................................................................................................
GB - 7
REMOTECONTROL (J1)
1. Install the lithium battery (1) in the unit in correct polarity (text towards the battery compartment cover) and close the
battery compartment.
2. Fix the unit on the bracket by a screw.
3. Click in the decorative inlay (2) and the joystick button (3).
4. Move the remote control into the bracket until it clicks.
The fixation system of the remote control allows placing the unit on the right or on the left side of the steering wheel. The
suggested position for the remote control is at 10 o’ clock or 2 o’ clock on the steering wheel.
The backside of the remote control is transmitting infrared light and needs to be directed towards the infrared receiver of
the screen. Do no cover the backside of the remote control! The screen needs to be placed at the same side of the steering
wheel as the remote control. If you have installed the remote control at the right side, you need to install the screen also
on the right side.
10 o’ clock 2 o’ clock
m_BluePerfection_GB.pmd 10.02.2006, 15:17
7

...........................................................................................................................................................................
GB - 8
The fixation needs to be done as it is shown in the picture below.
SCREENUNIT (D1)
Mount the bracket of the screen unit (SC1) on the dashboard or any other place where it is clearly visible, but do not
impair control or operation of the vehicle. Take into consideration that the infrared receiver for the remote control is built-
in in the screen unit, so for a reliable operation make sure that the screen and the remote control are in visible area at
40-50 cm distance and in an angle of about 30 degrees.
Search for a location in your car where the screen unit fits and where it is comfortable for use. Make sure that the location
in your car where you would like to install your screen unit is free from dust and dirt.
The bracket for the screen unit can be fixed in 2 ways:
1. Immediately to the dashboard using the installation screws.
2. To the fixing plate using the installation screws. The fixing plate should then be fixed to the dashboard or to any
other place in the car by means of the double sided tape plate.
3. If you want to fix the screen unit on a vertical surface of the dashboard, you can use the angle bracket.
MICROPHONE(M1)
Mount the microphone close to the user’s head (30 cm is optimal) and position it so that it is directed towards the mouth.
Experience has shown that the best location is near the rearview mirror or to the left of the sun visor. To avoid echo we
recommend having a minimum distance of 1 meter between the microphone and the handsfree unit.
m_BluePerfection_GB.pmd 10.02.2006, 15:17
8

...............................................................................................................................................................................
GB - 9
Make sure to mount the microphone so that it is not exposed to air streams from the vents. Do not lay the microphone
cable in the heating, ventilation or AC systems. Fix the microphone using Velcro.
SYSTEM CABLE (SC1)
The system cable SC1 comes out of the bracket of the screen unit and is used for connecting the screen unit to the
handsfree unit via a socket.
Ensure that the cable is placed so that it will not be damaged (e.g. not laid under car seats or over sharp edges).
CONNECTING TO THE POWER
There are 2 ways of connecting the Blue Perfection to the car’s electronic system:
1. Plug & play connection: via the adapter for the cigarette lighter (SC3).
2. Built-in connection: immediately to the car’s electronic system via system cable SC2.
The wires of the cable SC2 are color coded. They are listed in Table 1 in columnAand each wire should be connected to the
corresponding item listed in column B.
Table 1.
A B
Red wire The + voltage of the car’s power supply
Black wire The negative GND connection
Blue wire Ignition
Brown wire Used for Car Radio muting (CRM) and has to be connected to the Car Radio (Mute)
• To avoid distortions make sure that the cables are laid far away from the electronic systems of the car.
• Connect the wires with the contact clips. Put the car wire in the through groove of the clips and the cable wire in the
groove with the confining rib.
Attention!
If there is no “Ignition” wire or if it is unavailable, you should connect the blue cable wire to the red wire of the handsfree
unit and the red cable wire to the “Discontinuous” wire of the car which keeps the voltage when the ignition is turned off.
CAR RADIO MUTING (CRM)
The Blue Perfection allows muting your Car Radio when there is an incoming call.
• Check the user’s manual of your Car Radio to make sure that it has a Mute function. If additional settings have to
be set from the Car Radio menu, make sure that they are done correctly.
• Remove the control panel of the Car Radio.
• Remove the decorative panel and take out the Car Radio from the sleeve using the handles. Disconnect the Car
Radio plug.
m_BluePerfection_GB.pmd 10.02.2006, 15:179

...........................................................................................................................................................................
GB - 10
• Connect the wires of the Blue Perfection to the corresponding wires from the car jack or from the ISO jack of the
Car Radio according to Table 1. Use 4 contact clips for the connection.
• Restore the connection and installation of the Car Radio.
OPERATION
SWITCHING ON/OFF
If mr Handsfree Blue Perfection is connected to the power via the adapter with cable SC3, you can switch on the unit by
clicking the adapter into the cigarette lighter.
If mr Handsfree Blue Perfection is connected to the power with cable SC2, the unit will switch on automatically when you
turn the ignition key.
Mr Handsfree Blue Perfection will turn off automatically when the ignition is off.
MENUSTRUCTURE
All functions of the unit are grouped in the menu.
To access the menu press the central button of the joystick once. The menu of quick access appears on the
display.
To move in the menu, use the joystick and the 2 control buttons of the remote control.
The menu structure is shown below:
m_BluePerfection_GB.pmd 10.02.2006, 15:1710

...............................................................................................................................................................................
GB - 11
m_BluePerfection_GB.pmd 10.02.2006, 15:1711

...........................................................................................................................................................................
GB - 12
PAIRING, CONNECTION AND DISCONNECTION
A. PAIRING
• For pairing mr Handsfree Blue Perfection with your Bluetooth®mobile phone, use the remote control to go to Main
menu Bluetooth®Pairing and press . Now mr Handsfree Blue Perfection is in registration mode. The
corresponding message appears on the display and a confirmation tone will be heard.
• Activate the Bluetooth®function in your mobile phone.
• Search for available Bluetooth®devices by entering the corresponding submenu of the phone. Your phone will find
all Bluetooth®devices within 10 m distance and display them as a list.
• Select “
BLUE PERFECTION ”from the list.
• Enter the passkey “0000”. “
PAIRING OK ”will appear on the display and the device will turn to Standby mode.
“Blue Perfection”will be stored in the list of paired devices in your phone.
Note:
If necessary, the pairing mode could be activated by pressing the left button on the screen unit. The button
should be pressed and held for more than 5 sec.
B.CONNECTION
In some cases the device could be disconnected from your phone. For example, if the Blue Perfection was switched off.
To restore the connection between the Blue Perfection and your phone:
• Switch on the power and the connection will be restored automatically; OR
• Use the joystick to go to Main menu Bluetooth®Connection. “
CONNECTION... ”will appear on the display; OR
• Press and hold the left button on the screen unit for more than 5 sec.
C.DISCONNECTION
Sometimes you need to disconnect your phone from the Blue Perfection. For example, if the phone should communicate
with another Bluetooth®device.
m_BluePerfection_GB.pmd 10.02.2006, 15:1712

...............................................................................................................................................................................
GB - 13
To disconnect the Blue Perfection and your phone:
• Switch off the Blue Perfection; OR
• Select the menu item: Main menu Bluetooth®Disconnection; OR
• Take the phone away from the Blue Perfection on more than 10 meters; OR
• Disconnect the Blue Perfection and the phone through the phone’s menu.
Note:
If the Blue Perfection and your phone were disconnected and you want to connect them again, it is not necessary
to pair these devices again. Restoring the connection will be performed without asking for the access code.
FUNCTIONS
1. VOICE DIALING
If your phone supports voice dialing and there are saved voice tags (names), you can use this function via the Blue
Perfection.
2. MAIN MENU
2.1 Bluetooth®
2.1.1 Connection
Use this item to connect the Blue Perfection and your phone.
2.1.2 Disconnection
Use this item for destroying the connection between the Blue Perfection and your mobile phone.
2.1.3 Pairing
Use this item to pair the Blue Perfection and your Bluetooth®mobile phone.
2.2 Phonebooksettings
m_BluePerfection_GB.pmd 10.02.2006, 15:1713

...........................................................................................................................................................................
GB - 14
2.2.1 Copy
Use this item to copy the phonebook of your phone to the Blue Perfection phonebook. The maximum number
of phonebook records is 200.
Since not all Bluetooth®phones support phonebook copying using Bluetooth®, you can also use the built-in SIM card
reader to download your phonebook data in the Blue Perfection memory. To copy the phonebook using the SIM card
reader, please disconnect the screen from the bracket SC1, insert the SIM card into the SIM card holder according to the
picture, and connect the screen to the bracket. Make sure that you push the card deep enough, until it clicks into place.
If the SIM card is PIN code protected, the screen keypad will appear:
• Enter the PIN code by using the Up, Down, Left and Right buttons to select digits.
• Use to confirm your choice. The selected digits will appear on the top part of the display.
• To delete an incorrect digit, press .
• Press to confirm the PIN code.
• The phonebook copying will start accordingly. The existing phonebook, stored in the Blue Perfection, will
be erased automatically.
• If your SIM card is not PIN code protected, the phonebook copying process will start automatically.
• As soon as the phonebook copying process is finished, you can disconnect the screen from the bracket
and remove the SIM card from the holder. To release the card from the holder, you should press it.
m_BluePerfection_GB.pmd 10.02.2006, 15:1714

...............................................................................................................................................................................
GB - 15
• Insert the SIM card in your mobile phone and switch it on.
• Connect the screen to the bracket.
• Activate the main menu of the Blue Perfection and select Bluetooth®Connection.
• Press to confirm your choice.
• The connection should be restored.
2.2.2. Open
Use this item to view the phonebook records.
2.2.3. Erase
Use this item to delete all the phonebook records.
2.3 Volume of conversation and call ring
This item is used for setting the desired volume of the speaker of the Blue perfection in Talk mode and the volume of the
incoming call ringer.
Use the Up and Down buttons of the joystick to set the volume. There are 16 volume-levels.
2.4 Display settings
2.4.1 Brightness
Choose this menu item for setting the brightness of the display backlight.
m_BluePerfection_GB.pmd 10.02.2006, 15:1715

...........................................................................................................................................................................
GB - 16
• Use the Up and Down buttons of the joystick to choose the desired brightness.
• Press to confirm or to restore the previous setting of the brightness.
The custom setting of brightness has 16 levels. Level 0 switches the backlight off, level 15 is the maximum.
2.4.2Contrast
Choose this menu item for setting the contrast of the display.
• Use the Left and Right buttons of the joystick to choose the desired contrast.
• Press to confirm or to restore the previous setting of the contrast.
The contrast has 16 levels. Level 0 is the minimum, level 15 is the maximum.
2.4.3 Color
Choose this menu item for setting the color of the display backlight.
Choose one of the available colors:
1. Red
2. Orange
3. Yellow
4. Green
5. White
6. Custom
Choose the menu item “CUSTOM” to set the color of the backlight smoothly.
• Use the Up and Down buttons of the joystick to choose the desired color.
• Use the Left and Right buttons of the joystick to choose the desired level of the color.
• Press to confirm or to restore the previous setting of the color.
m_BluePerfection_GB.pmd 10.02.2006, 15:1716

...............................................................................................................................................................................
GB - 17
2.4.4 Rotate
For mounting in upside down position, you can rotate the screen.
Choose the menu item ”
ROTATE “ and press to confirm.
2.5 Settings
2.5.1 Language
Choose the menu item “ SETTINGS ”.
• Choose the “ LANGUAGE ”item and press .
• Choose one of the available languages (English, Russian, Dutch …).
• Press to confirm or to restore the previous setting of the language.
2.5.2 Backlight off time
• Choose “ BACKLIGHT OFF TIME ”to set the time after which the backlight will be switched off.
• Press .
• Use the Left and Right buttons of the joystick to set the timer. If you chose “
ALWAYS ON ”, the backlight will not be
switched off. Timer steps are 10 sec, the maximum is 1 min.
• Press to confirm or to restore the previous setting and exit the menu.
2.5.3 Set Default
With this item you can restore the factory settings of the Blue Perfection.
Parameter Value
Brightness 15/15 (max)
Contrast 8/15 (mid)
Backlight Color White
Language English
Backlight off time 10 sec
m_BluePerfection_GB.pmd 10.02.2006, 15:1717

...........................................................................................................................................................................
GB - 18
• In the submenu “ SETTINGS ”, select the item “ SET DEFAULT ” and press to confirm.
• “ SET DEFAULT? ”will appear on the display. Press to confirm or to cancel.
2.5.4 Software version
• In the submenu “ SETTINGS ”, select the item “ SOFTWARE VERSION ” and press to confirm.
• The number of the software version will appear on the display.
3. PHONEBOOK
You can use the phonebook for dialing out. The records of the phonebook are displayed in alphabetical order in the top part
of the display. The Blue Perfection phonebook can store up to 200 records. For a quick search of the desired name, find
its first letter with the cursor in the bottom part of the display using the navigation buttons of the joystick.
The phonebook copying process is described in chapter 2.2.1.
4. LCD KEYPAD
By using the LCD keypad and the joystick of the remote control you can dial out any number.
• Use the Up, Down, Left and Right buttons of the joystick to move and choose a digit on the display.
• Press the button to confirm.
Note:
The cursor always moves back to “5” after you have selected a digit. This is because the “5” is close to all of the
other digits.
5. SMS
With this item of the menu you can copy received SMS from your phone’s memory or SIM card (up to 20).
You will see the first word of each message. By clicking these words, you will open the message and see more details.
Note:
This function is not supported by some mobile phones due to their specific functionality.
6. CALL LIST
This item of the menu could be accessed by a single press of the button on the remote control when you are in the
main menu. Then you can choose 1 of 3 lists:
• List of outgoing calls.
• List of incoming calls.
• List of missed/rejected calls.
Every list can store up to 10 numbers and names if they are saved in the phonebook.
m_BluePerfection_GB.pmd 10.02.2006, 15:1718