MSA QuickServer FS-QS-2XX0 User manual

Operating Manual
QuickServer FS-QS-2XX0 Start-up Guide
Revision: 2.G
Document No.:T18627
Print Spec: 10000005389 (F)
MSAsafety.com

© MSA 2021. All rights reserved
MSA Safety
1991 Tarob Court
Milpitas, CA 95035
U.S. Support Information:
[phone]
[phone]
Email: [email protected]
EMEA Support Information:
[phone]
Email: [email protected]
For your local MSA contacts, please go to our website www.MSAsafety.com

Contents
1 About the QuickServer 5
1.1 Certification 5
1.2 Supplied Equipment 5
2 Equipment Setup 6
2.1 Mounting 6
2.2 Physical Dimensions 7
3 Installing the QuickServer 8
3.1 DIP Switch Settings 8
3.1.1 Bias Resistors 8
3.1.2 Termination Resistor 9
3.2 Connecting the R1 & R2 Ports 10
3.2.1 Wiring 10
3.2.2 Supported RS-485 Baud Rates by Protocol 10
3.3 10/100 Ethernet Connection Port 11
4 Power up the QuickServer 12
5 Connect the PC to the QuickServer 13
5.1 Connecting to the Gateway via Ethernet 13
5.1.1 Changing the Subnet of the Connected PC 13
5.2 Navigate to the Login Page 13
6 Setup Web Server Security 14
6.1 Login to the FieldServer 14
6.2 Select the Security Mode 16
6.2.1 HTTPS with Own Trusted TLS Certificate 17
6.2.2 HTTPS with Default Untrusted Self-Signed TLS Certificate or HTTP with Built-in Payload Encryption 17
7 Configuring the QuickServer 18
7.1 Configure Network Settings 19
7.1.1 Using FS-GUI to Input Network Settings 19
7.1.2 Routing Settings 20
7.1.3 Ethernet 1 Network Settings 21
7.2 Retrieve the Sample Configuration File 22
7.3 Change the Configuration File to Meet the Application 22
7.4 Load the Updated Configuration File 23
7.4.1 Using the FS-GUI to Load a Configuration File 23
7.4.2 Retrieve the Configuration File for Modification or Backup 24
7.5 Test and Commission the QuickServer 25
7.5.1 Accessing the Grid 25
8 Grid Setup 26
8.1 Registration Process 26
8.2 User Setup 29
8.3 Finish Registering the FieldServer 31
8.4 Login to the Grid 33
QuickServer FS-QS-2XX0 Start-up Guide 3

9 Troubleshooting 35
9.1 Communicating with the QuickServer Over the Network 35
9.2 Taking a FieldServer Diagnostic Capture 36
9.3 LED Functions 37
9.4 Factory Reset Instructions 38
9.5 Internet Browser Software Support 38
10 Additional Information 39
10.1 SSL/TLS for Secure Connection 39
10.1.1 Configuring FieldServer as a SSL/TLS Server 39
10.1.2 Configuring FieldServer as SSL/TLS Client 42
10.2 Change Web Server Security Settings After Initial Setup 43
10.2.1 Change Security Mode 44
10.2.2 Edit the Certificate Loaded onto the FieldServer 45
10.3 Change User Management Settings 46
10.3.1 Create Users 47
10.3.2 Edit Users 48
10.3.3 Delete Users 49
10.3.4 Change FieldServer Password 50
10.4 QuickServer Part Numbers 51
10.5 Compliance with UL Regulations 51
10.6 Specifications 52
10.7 Grid Connection Warning Message 53
11 Limited 2 Year Warranty 54
4 QuickServer FS-QS-2XX0 Start-up Guide

1 About the QuickServer
QuickServer is a high performance, cost effective Building and Industrial Automation multi-protocol gateway providing
protocol translation between serial/Ethernet devices and networks.
NOTE:For troubleshooting assistance refer to Section 9 Troubleshooting, or any of the troubleshooting
appendices in the related driver supplements. Check the MSA Safety website for technical support resources
and documentation that may be of assistance.
The QuickServer is cloud ready and connects with MSA Safety’s Grid. See Section 8 Grid Setup for further information.
NOTE:The FS-QS-2XX0-F contains all Serial and Ethernet drivers.
1.1 Certification
BTL Mark – BACnet Testing Laboratory
The BTL Mark on QuickServer is a symbol that indicates that a product has passed a series of
rigorous tests conducted by an independent laboratory which verifies that the product correctly
implements the BACnet features claimed in the listing. The mark is a symbol of a high-quality BACnet
product.
Go to www.BACnetInternational.net for more information about the BACnet Testing Laboratory. Click
here for the BACnet PIC Statement. BACnet is a registered trademark of ASHRAE.
1.2 Supplied Equipment
QuickServer Gateway
• Preloaded with two selected drivers. A sample configuration file is also loaded.
• All instruction manuals, driver manuals, support utilities are available on the USB drive provided in the optional
accessory kit, or on the MSA website.
Accessory kit (optional) (Part # FS-8915-38-QS) includes:
• 7-ft Cat-5 cable with RJ45 connectors at both ends
• Power Supply -110/220V (p/n 69196)
• Screwdriver for connecting to terminals
• USB Flash drive loaded with:
◦ QuickServer Start-up Guide
◦ FieldServer Configuration Manual
◦ All FieldServer Driver Manuals
◦ Support Utilities
◦ Any additional folders related to special files configured for a specific QuickServer
◦ Additional components as required - see driver manual supplement for details
QuickServer FS-QS-2XX0 Start-up Guide 5

2 Equipment Setup
2.1 Mounting
The QuickServer can be mounted using the DIN rail mounting bracket on the back of the unit.
6 QuickServer FS-QS-2XX0 Start-up Guide

2.2 Physical Dimensions
QuickServer FS-QS-2XX0 Start-up Guide 7

3 Installing the QuickServer
3.1 DIP Switch Settings
3.1.1 Bias Resistors
To enable Bias Resistors, move both the BIAS- and BIAS+ dip switches to the right in the orientation shown
above.
The QuickServer bias resistors are used to keep the RS-485 bus to a known state, when there is no transmission on the line
(bus is idling), to help prevent false bits of data from being detected. The bias resistors typically pull one line high and the
other low - far away from the decision point of the logic.
The bias resistor is 510 ohms which is in line with the BACnet spec. It should only be enabled at one point on the bus (for
example, on the field port were there are very weak bias resistors of 100k). Since there are no jumpers, many QuickServers
can be put on the network without running into the bias resistor limit which is < 500 ohms.
NOTE:See www.ni.com/support/serial/resinfo.htmfor additional pictures and notes.
NOTE:The R1 and R2 DIP Switches apply settings to the respective serial port.
NOTE:If the gateway is already powered on, DIP switch settings will not take effect unless the unit is power
cycled.
8 QuickServer FS-QS-2XX0 Start-up Guide

3.1.2 Termination Resistor
If the QuickServer is the last device on the serial trunk, then the End-Of-Line Termination Switch needs to be enabled. To
enable the Termination Resistor, move the TERM dip switch to the right in the orientation shown in above.
Termination resistor is also used to reduce noise. It pulls the two lines of an idle bus together. However, the resistor would
override the effect of any bias resistors if connected.
NOTE:The R1 and R2 DIP Switches apply settings to the respective serial port.
NOTE:If the gateway is already powered on, DIP switch settings will not take effect unless the unit is power
cycled.
QuickServer FS-QS-2XX0 Start-up Guide 9

3.2 Connecting the R1 & R2 Ports
For the R1 Port only: Switch between RS-485 and RS-232 by moving the number 4 DIP Switch left for RS-485 and right
for RS-232 (see images in Section 3.1 DIP Switch Settings).
The R2 Port is RS-485.
Connect to the 3-pin connector(s) as shown below.
3.2.1 Wiring
RS-485 RS-232
BMS RS-485 Wiring Gateway Pin Assignment BMS RS-232 Wiring Gateway Pin Assignment
RS-485 + TX + RS-232 - TX +
RS-485 - RX - RS-232 + RX -
GND GND GND GND
NOTE:Use standard grounding principles for GND.
3.2.2 Supported RS-485 Baud Rates by Protocol
The supported baud rates for either port is based on the protocol of the connected devices.
The following baud rates are supported for Modbus RTU:
2400, 4800, 9600, 19200, 38400, 57600, 76800, 115200
The following baud rates are supported for BACnet MS/TP:
9600, 19200, 38400, 76800, 115200
10 QuickServer FS-QS-2XX0 Start-up Guide