MULTIQUIP Mikasa MTR-35W User manual

OPERATION MANUAL
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Revision #9 (11/03/20)
SERIES
MODEL MTR-35W
TAMPING RAMMER
(ROBIN EC-08GH ENGINE)
To find the latest revision of this publication or
associated parts manual, visit our website at:
www.multiquip.com

PAGE 2 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 3
TABLE OF CONTENTS
MTR-35W
Table Of Contents ................................................. 3
Rules For safe Operation .................................. 4-5
Operation and Safety Decals ................................ 6
General Information .............................................. 7
Specification .......................................................... 8
Controls and Components .................................... 9
Operation .......................................................10-12
Maintenance ....................................................... 13
Troubleshooting Guide ...................................14-15
NOTE
Specification and part number
are subject to change without
notice.

PAGE 4 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used when
operating the MTR-35W Tamping Rammer:
GENERAL SAFETY
■ DO NOT operate or service this equipment before
reading this entire manual.
■ This equipment should not be operated by persons under 18
years of age.
■ NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-toed
boots and other protective devices required by the
job.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
■ NEVER operate this equipment under the
influence or drugs or alcohol.
■ ALWAYS check the machine for loosened threads or bolts before
starting.
■ ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the rammer.
■ ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■ NEVER operate the rammer in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe
bodily harm or even death.
■ Topping-off to filler port is dangerous, as it tends to spill fuel.
■ The engine section of this rammer requires an adequate
free flow of cooling air. NEVER operate the rammer in any
enclosed or narrow area where free
flow of the air is restricted. If the air
flow is restricted it will cause serious
damage to the rammer or engine
and may cause injury to people.
Remember the rammer's engine
gives off
DEADLY carbon monoxide
gas.
■ High Temperatures – Allow the engine to cool before
adding fuel or performing service and maintenance
functions. Contact with
hot components can cause serious
burns.
■ ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result from
fuel vapors, or if fuel is spilled on a hot
engine.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Manufacture does not assume responsibility for any accident
due to equipment modifications.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or rammer.

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 5
RULES FOR SAFE OPERATION
■ NEVER Run engine without air filter. Severe engine may
occur.
■ Always service air cleaner frequently to prevent carburetor
malfunction.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using rammer.
■ Always store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■ NEVER Run engine without air cleaner. Severe engine
damage may occur.
■ Always read, understand, and follow procedures in Operator’s
Manual before attempting to operate equipment.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using pump.
■ Always store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■ Refer to the ROBIN Engine Owner's Manual for engine
technical questions or information recommended by Multiquip
for this equipment. Damage to the equipment and/or injury to
user may result.
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securly and close fuel cock to prevent
fuel from spilling.
■ Drain fuel when transporting rammer over long distances or
bad roads.
■ When placing the rammer inside a truck-bed for transport,
always tie-down the rammer.
Emergencies
■ Always know the location of the nearest fire extinguisher
and first aid kit . Know the location of the nearest telephone.
Also know the phone numbers of the nearest
ambulance ,
doctor and fire department . This information will be
invaluable in the case of an emergency.
Maintenance Safety
■ NEVER lubricate components or attempt service on a running
machine.
■ Always allow the machine a proper amount of time to cool
before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always replace
broken parts.
■ Dispose of hazardous waste properly. Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■ DO NOT use plastic containers to dispose of hazardous
waste.

PAGE 6 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)
OPERATION AND SAFETY DECALS

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 7
Definition of Tamping Rammer
The Mikasa MTR-35W Tamping Rammer is a powerful
compacting tool capable of applying a tremendous force in
consecutive impacts to a soil surface. Its applications include
soil compacting for backfilling for gas pipelines, water pipelines
and cable installation work.
The impact force of the MTR-35W levels and uniformly compacts
voids between soil particles to increase dry density.
Circular motion is converted to create impact force.The MTR-
35W tamping rammer develops a powerful compacting force at
the foot of the rammer.To maintain optimum performance, proper
operation and service are essential.
Construction of Tamping Rammer
The Mikasa MTR-35W is equipped with an Robin air cooled,
oil-injected two cycle gasoline engine.Transmission of the power
takes place by increasing the engine speed to engage the
centrifugal clutch.
Rammer Gearbox and Spring Cylinder
The Mikasa MTR-35W uses an oil bath lubrication system.
Always check the oil level through the oil level sight glass at the
rear of the tamper foot.
Controls
Before starting the MTR-35W Tamping Rammer identify and
understand the function of the controls, see Figure 1 on page 11.
GENERAL INFORMATION

PAGE 8 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)
NOTE
Specifications are general and are subject to change without notice. If exact
measurements are required, equipment should be weighed and measured.
SPECIFICATIONS
snoitacificepSremmaRW53-RTM.1elbaTsnoitacificepSremmaRW53-RTM.1elbaT snoitacificepSremmaRW53-RTM.1elbaT snoitacificepSremmaRW53-RTM.1elbaTsnoitacificepSremmaRW53-RTM.1elbaT
LEDOM)cirtem(.S.UW53-RTM
thgieHllarevO)mm550,1(.ni5.14
pirgeldnaHfothgieH)mm009(ni8/3.53
htdiWllarevO)mm063(
.ni4/1.41
htgneLrevO)mm545(.ni5.12
snoisnemiDetalP )mm072X051(.NI8/5.01X8/7.5
etunim/swolB057~027
aerAgnipma
T )rhrepm.qs002-041(rhrep.tf.qs351,2-705,1
ecroFtcapmI)wolb/gk055(wolb/.sbl0121
hctulClagufirtneCcitamotuA
thgieWgnitarepO)gk83(.sbl48
snoitacificepSenignESH80-CENIBOR.2elbaTsnoitacificepSenignESH80-CENIBOR.2elbaT snoitacificepSenignESH80-CENIBOR.2elbaT snoitacificepSenignESH80-CENIBOR.2elbaTsnoitacificepSenignESH80-CENIBOR.2elbaT
LEDOMENIGNEHG80-CENIBOR
epyTenignEenilosaGekortS2delooC-riA
ekortSXeroB mm04Xmm05(.ni23/7-1X.ni23/13-1
tnem
ecalpsiDnotsiP)cc5.87(.ni.uc21.5
oitaRnoisserpmoC1:5.6
tuptuOdetaRsuounitnoCmpr005/ph2.2
tuptuO.xaMmpr005,5/
ph3.3
euqroT.xaM )mpr006,3/m-gk15.0(mpr006,3bl-tf7.3
metsySgnilooCnaFyBdelooC-riA
metsySnoitacirbuL metsySg
niyarpSliOnoitacirbuL-leuF
noitpmusnoCleuF)mpr005,4/ph2.2(h/ph/bl48.0
leuF1liO:52enilosaG
thgieWyrD)gk4.7(.
sbl3.61
gulPkrapSSH6-BKGN
metsySgnitratSretratSlioceR

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 9
MTR-35W — CONTROLS AND COMPONENTS
Figure 1 shows the location of the controls and components
for the MTR-35W Tamping Rammer. The functions of each
control is described below:
1. Throttle Lever – Controls engine speed and the tamping
action of the rammer.
2. Engine Stop Switch – Controls the starting and stopping
of the engine. Switch must be in the "ON" position when
starting the engine.
3. Choke Lever – Used when starting the engine.Normally
used in cold weather conditions. In cold weather turn the
choke lever to the fully closed position, in warm weather
set choke lever half way or completely open.
4. Fuel Shut-OffValve – Supplies fuel from the fuel tank to
the engine.To begin fuel flow move the fuel shut-off valve
downward.
5. Grease Fill Plug – Open this plug to add oil to the oil bath
reservoir.
6. FuelValve – Open this valve to remove excess fuel from
the carburetor or crankcase.
7. Pre- Cleaner – Pre-cleans (first stage) dirt and other
debris from entering the engine.
L1. A Returned Material Authorization must be approved by Multiquip prior to shipment. A copy of the Authorization must
accompany the shipment to the designated Warehouse. A copy of the original Multiquip invoice to the customer must
also accompany the shipment.
8. Foot– Laminated wood with tempered steel plate for
superior shock absorption.
9. Recoil Starting Handle – Used when starting the engine.
Pull starter handle sharply and quickly, then return
starter handle to starter case before releasing.
10. Fuel Tank/Cap – Poly fuel tank to avoid rust and
corrosion, remove this cap to add unleaded gasoline. Mix
unleaded gasoline with 2-stroke outboard motor oil at a
25:1 ratio
11. Engine Air Cleaner – Prevents dirt (second stage) and
other debris from entering the engine.
12. Handle – To operate rammer GRIP handle assembly
firmly on both sides.
13. Muffler– Used to reduce noise and emissions.
14. Spark Plug – Provides spark to the ignition system,
replace with engine manufactures recommended type
spark plug.
15. Nameplate – Displays information regarding the rammer.
16. Grip – When transporting the rammer, carry it by griping
the handle.
17. Dust Sleeve – Prevents dust and debris from entering
into the spring cylinder.
Figure 1. MTR-35W Rammer

PAGE 10 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)
,g
it often.
MTR-35W — OPERATION
DO NOT use your rammer until this section is thoroughly
understood.
This section is intended to assist the operator with the initial
start-up of the MTR-35W Tamping Rammer. It is extremely
important that this section be read carefully before attempting to
operate the rammer.
Figure 2. Grip Handle
2. The rammer should be greased with three shots of grease
after each eight (8) hours of use.
3. Use MQ HIGH TEMPERATURE GREASE, (part #GS or its
equivalent
4. Equivalent greases include Shell Darina or Texaco
Thermatex, both of which have a bentone base and EP-2
rating.
5. If an inferior grease is used, it may become too thick or too thin
due to changes in temperature, and improper lubrication
could result.
6. The rammer is equipped with a two-cycled gasoline engine.
A regular grade gasoline should be used. High test ethyl
gasoline is not recommended.The oil should be good grade
of two- cycle or outboard motor oil.
Prior to starting the operation
1. When transporting the machine, carry it by the grip handle
located on the body (Figure 2).
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION:
Failure to understand the operation of the MTR-
35W Tamping Rammer could result in severe
damage to the rammer or personal injury.
Engine
Before pouring fuel into the fuel tank (Figure 3) perform the
following:
1. Fill the fuel tank (Figure 3 ) with unleaded gasoline. This
rammer is equipped with a 2-cycle (mixed fuel) gasoline
engine. Use a well blended mixture of fuel (25 parts gasoline
to 1 part of 2-cycle outboard motor oil).
2. When filling the rammer with fuel, be sure to use the fuel
strainer located inside the fuel tank. Make sure that the fuel
stopper is installed in the cap as fuel may splash out of the
tank due to vibration.
3. Durinh initial operation (first 20 hours of use), it is recom-
mended that you use a well blended mixture ( 15 parts
unleaded gasoline to 1 part 2-cycle outboard motor oil) for
longer engine life.
4. Low levels of oil may result in engine seizure due to high
levels of consumption during operations.
5. Check the engine oil level and if the engine oil level is low, it
should be refilled. Use the proper motor oil as suggested in
the Table 3 below.
Figure 3. Fuel Tank
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION:
DO NOT USE REGULAR AUTOMOTIVE-TYPE
MOTOR OILWHEN MIXING FUEL.
edarGliOrotoM3elbaT
erutarepmeTronosaeS liorotomfoedarG
)ssalcSMnahtrehgih(
nmutuAroremmuS,gnirpS
F°51+otF°021+ 03EAS
retniW
F°5
1+otF°04+ 03EAS
F°51+woleB03-W01EAS

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 11
MTR-35W — OPERATION
5. If engine fails to start, move the choke lever (Figure 4) to the
half open position to avoid flooding.
6. Repeat steps 1 thru 5.
7. If the engine does not start after repeated attempts,
check the spark plug for excess fuel. Clean and replace
the spark plug as needed.
Figure 5. Engine On/Off Switch
3. Close the choke lever (Figure 4) and move the throttle lever
(Figure 9) to the "Full Open" position. Turning the choke
lever 90 degrees clockwise closes the choke .In cold weather,
start the unit with choke fully closed. In warm weather or when
the engine is warm, the unit can be started with choke halfway
or completely open.
4. Grip the recoil starter (Figure 7) handle and pull it until you
feel a slight resistance. Then pull sharply and quickly. Return
the recoil starter handle to the starter position before releas-
ing.
Inspection
1 . Check all nuts, bolts fasteners for tightness. Retighten as
necessary.
2. Clean any dirt from the recoil starter and foot pedestal. Wipe
the entire unit clean before operating.
3. Replace any missing or damaged Safety Operation decals.
4. Adjust height of handle. Adjust handle by loosening nuts and
moving handle to suit operation. Retighten nuts.
Initial Start-up
When starting the MTR-35W Tamping Rammer perform the
following:
1. Open the fuel shut- off valve by moving the fuel cock lever
to the
open position (Figure 4).
Figure 4. Fuel Cock and Choke Lever
2. Set the engine ON/OFF switch (Figure 5) to the "ON"
position (start).
3. Close the choke lever (Figure 4) and move the throttle lever
(Figure 9) to the "Full Open" position. Turning the choke
lever 90 degrees clockwise closes the choke .In cold weather,
start the unit with choke fully closed. In warm weather or when
the engine is warm, the unit can be started with choke halfway
or completely open.
4. Move the throttle lever (Figure 6) between 1/4 to 1/2 from the
idle position.
Figure 7. Recoil Starter
Figure 7. Throttle Lever (1/4 to 1/2)
p

PAGE 12 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)
Stopping The Engine
Normal Shutdown
1. Move throttle lever quickly from the FULL OPEN to IDLE
position (Figure 10) and run the engine for three minutes at
low speed.After the engine
cools , turn the engine start/stop
switch to the “OFF” position (Figure 5) until engine comes
to a complete stop.
Figure 10. Throttle Lever (Idle)
2. Close the fuel shut- off valve by moving the fuel cock lever to
the CLOSED position. See Figure 4.
Emergency Showdown
1. Move the throttle lever quickly to the IDLE position, and turn
the engine start/stop switch (Figure 5) to the
STOP position.
MTR-35W — OPERATION
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION:
Make sure that the throttle lever is moved to the
FULL OPEN position. Operating the rammer at
less than full speeds can result in damage to
the clutch springs or foot
Figure 9. Throttle Lever (Full Open)
2. The MTR-35W Tamping rammer is designed to run at 5,500
rpm. At optimum rpm the foot hits at the rate of 750 impacts
per minute. Increasing throttle speed past factory set rpm
does not increase impacts and may damage unit.The MTR-
35W is designed to advance while tamping. For faster
advance, pull back slightly on the handle so that rear of foot
contacts soil first.
7. If the carburetor is flooded or the crankcase is loaded with
excess fuel, open the drain plug as shown in (Figure 8) and
drain out excess fuel.
Figure 8. Drain Plug
Operation
1. To start the rammer tamping action, move the throttle lever
(Figure 9) quickly from IDLE (close) to the FULL OPEN
position . DO NOT move the throttle lever slowly as this may
cause damage to the clutch or spring.

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 13
Maintenance
Perform the scheduled maintenance procedures as indicated:
DAILY
■ Thoroughly remove dirt and oil from the engine and control
area. Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
spring box and bellows for oil leaks. Repair or replace as
needed.
WEEKLY
■ Remove the fuel filter cap and clean the inside of the fuel
tank.
■ Remove or clean the filter at the bottom of the tank.
■ Remove and clean the spark plug, then adjust the spark gap
to 0.02~0.03 inch (0.6~0.7 mm). This unit has electronic
ignition, which requires no adjustments.
■ Clean air cleaner cover.
200 - 300 HOURS (Pre-Cleaner)
■ Remove the element from the pre-cleaner (Figure 11) at the
top of the crankcase (body side) and clean it with cleaning oil
(kerosene).
MTR-35W — MAINTENANCE
■ Lubricate the top element (yellow) with 2~5 cc of engine oil
SAE-30.
■ Lubricate bottom element (gray) with 13 ~15 cc of engine oil
SAE-30 and completely squeeze out the excess oil from the
element before installing.
■ The air cleaner on the engine side will hardly be contaminated,
if it is, however after cleaning the element with kerosene, dip
it in mixed oil consisting of 3 parts of gasoline and 1 part of
engine oil. Then tightly squeeze outer primary element
(sponge) and shake off well the inner secondary element
before installing them.
FUEL LINES
■ Check the fuel line regularly for damage and ensure that
there are no leaks.
■ Replace fuel line every 2 years to maintain performance.
Figure 11. Pre-Cleaner
YELLOW
GRAY
13 -15 CC
SAE 30
2-5 CC
SAE 30
PRE-CLEANER
It is normal for a new 2-stroke engine to emit
excess smoke, until moving parts have been
seated to their normal operating specifications.
This excess smoke normally stops after one full
tank of fuel.
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION:
CLEANINGTHE RAMMER
■ If using a high pressure spray washer, be careful not to splash
water directly on the air cleaner, carburetor, muffler, fuel and
oil tank caps. Excessive amounts of water may cause severe
engine damage.
Yearly
■ Check the fuel line and the oil line regularly for damage and
to ensure that there are no leaks.
■ Replace the oil and fuel lines every two years to maintain the
performance and flexibility lines.
Long Term Storage
■ Drain fuel from fuel tank, fuel line and carburetor.
■ Remove spark plug and pour a few drops of motor oil into
cylinder. Crank engine 3 to 4 times so that oil reaches all
internal parts.
■ Clean exterior of rammer with an oil-moistened cloth.
■ Store unit covered with plastic sheet in moisture free and
dust free location out of direct sunlight

PAGE 14 — MTR-35W — OPERATION MANUAL — REV. #9 (11/03/20)
MTR-35W —TROUBLESHOOTING GUIDE
GNITOOHSELBUORTENIGNE.4ELBAT
MOTPMYS MELBORPELBISSOP NOITULOS
tratsottluciffiD
gulpkrapstubelbaliavasileuF
elbaliavarewoP(.etingitonlliw
.)elbacnoisnethgihta
?egdirbgniebgulpnoitingI .metsysnoitingikcehC
?noitingitatisopednobraC .noitingiecalperronaelC
evitcefedoteudtiucrictrohS
?srotalusni
.srotalusniecalpeR
?pagkrapsreporpmI .pagtcerrocehtotpaggulpkrapsteS
gulpkrapstubelbaliavasileuF
rewoP(.etingitonlliw TON
.)elbacnoisnethgihtaelbaliava
?hctiwspotstatiucrictrohS .evitcefedfihctiwspotsecalpeR.tiucrichctiwspotskcehC
?evitcefedliocnoitingI .liocnoitingiecalpeR
gulpkrapsdnaelbaliavasileuF
noisserpmoc(setingi )lamron .
nobrachtiwdeggolcrelffuM
?stisoped
.relffumecalperronaelC
siytilauqleufdexiM
?etauqedani
.erutximliootleufkcehC
,retaw(etauqedaniesunileuF
?)tsud
.leufhserfhtiwecalperdnametysleufhsulF
?deggolcrenaelCriA .renaelcriaecalperronaelC
gulpkrapsdnaelbaliavasileuF
noisserpmoc(setingi wol .)
?teksagdaehrednilycevitcefeD .teksagdaehecalperrostlobdaehrednilycnethgiT
?nrowrednilyC .rednilycecalpeR
?esoolgulpkrapS .gulpkrapsnehgiT
yrotcafsitastonnoitarepO
elbaliavarewophguonetoN
-ssimon,lamronnoisserpmoc(
.)gnirif
?deggolcrenaelcriA
?enilleufniriA .enilleufmorf)riaevomer(deelB
taolfrotaerubracnilevelleuF
?reporpmirebmahc taolfrotaerubractsujdA
?rednilycnistisopednobraC rednilycecalperronaelC
elbaliavarewophguonetoN
-ssim,lamronnoisserpmoc(
.)gnirif
?evitcefedliocnoitingI .leufhserfhtiwecalperdnametysleufhsulF
?strohsnetfogulpnoitingI .noitinginaelc,seriwnoitingiecalpeR
,retaw(etauqedaniesunileuF
?)tsud
.leufhserfhtiwecalperdnametysleufhsulF
.staehrevoenignE
siytilauqleufdexiM
?etauqedani
.erutximliootleufkcehC
ninoitsopednobracevissecxE
?rebmahcnoitsubmoc
.esacknarcecalperronaelC
htiwdeggolcrelffumrotsuahxE
.nobrac
.relffumecalperronaelC
?tcerrocnieulavtaehgulpkrapS .gulpkrapsepyttcerrochtiwgulpkrapsecalpeR

MTR-35W— OPERATION MANUAL — REV. #9 (11/03/20) — PAGE 15
MTR-35W —TROUBLESHOOTING GUIDE
ENGINEENGINE
ENGINEENGINE
ENGINE
deunitnoc(GNITOOHSELBUORTENIGNE.4ELBAT )
MOTPMYS MELBORPELBISSOP NOITULOS
yrotcafsitastonnoitarepO
.setautculfdeepslanoitatoR
?reporpmitnemtsujdaronrevoG .reveltcerrocotronrevogtsujdA
?evitcefedgnirpsronrevoG .noitingiecalperronaelC
?citarrewolfleuF .enilleufkcehC
noitcushguorhtninekatriA
?enil
.enilnoitcuskcehC
gnikrowtonretratslioceR
.ylreporp
?trapgnitatornitsuD .ylbmessaretratsliocernaelC
?eruliafgnirpsgnirpS .gnirpslairpsecalpeR
GNITOOHSELBUORTREMMAR.5ELBAT
MOTPMYS MELBORPELBISSOP NOITULOS
ediutilpmatubsetatorenignE
.ekirtstonseodromrofinuton
revelelttorhtfodeepsgnitarepO
?tesyltcerrocnisi
.noitisoptcerrocotrevelelttorhtteS
?ssecxeniliO .leveltcerrocotgnirB.liossecxeniarD
?spilshctulC .hctulctsujdaroecalpeR
?eruliaFgnirpS .gnirpslairpsecalpeR
?reporpmienignefodeepS .gnittesMPRgnitarepotcerrocotdeepsenignetsujdA

OPERATION MANUAL
Your Local Dealer is:
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Inc.
(310) 537- 3700
6141 Katella Avenue Suite 200
Cypress, CA 90630
E-MAIL: [e-mail]
WEBSITE: www.multiquip.com
CANADA UNITED KINGDOM
Multiquip Multiquip (UK) Limited Head Office
[phone]
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
E-MAIL: [e-mail]
0161 339 2223
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
E-MAIL: [e-mail]
© COPYRIGHT 2020, MULTIQUIP INC.
Multiquip Inc
, the MQ logo and the Mikasa logo
are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual
MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.