MULTISPAN MI-631P User manual

TERMINAL CONNECTION
Front view (mm)
MECHANICAL INSTALLATION
MI-631PSIGNAL ISOLATOR
Linearized O/P 1.5KV isolation between supply, input & outputFEATURESTECHNICAL SPECIFICATIONZero & span correction facility through trim port Fast Response time <150ms Din Rail Mounting Input TypeInput Range 0 TO 100°C PT-100/3W INPUT SPECIFICATION:Current Input<100Ω Voltage Input>100KΩ CMRR>120dp (Typical) Temperature Co-efficient<100 PPM INPUT IMPEDANCE:DIMENSION:Size (HxWxD) mm76 X 27 X 116
767627116
Side view (mm)
PT-100/3W
MI 631P
SUPPLYOutput OUTPUT SPECIFICATION:Current Output>100@20mA DC with 500loadΩΩ OUTPUT IMPEDANCE:LOAD RESISTANCE4 to 20mA DCmA OuputLoad Voltage <10V Response Type<150msIsolation betweensupply, input & OutputAt least 1.5KV AC for 1 min Auxiliary VoltageSUPPLY:100 to 250V ACIsolation TypeOptical - 3 wayISOLATION:
PT-100/3W
Output
4 To 20mA DC
Supply
100 To 270V AC
www.multispanindia.com
Input
PT-100/3W
MI 631P
SUPPLY
Made in India
Range
0 To 100°C
Page 1

Read complete instructions prior to installation and operation of the unit. WARNING : Risk of electric shock.
SAFETY PRECAUTION!
All safety related codifications, symbols and instructions tha appear in this operating manual or on the equipment must be strictly followed to ensure the safety of the operating personnel as well as the instrument. If all the equipment is not handled in a manner specified bythe manufacturer, it might impair the protection provided by the equipment.
WARNING GUIDELINESWARNING : Risk of electric shock.
1. To prevent the risk of electric shock, power supply to the equipment must be kept OFF while doing the wiring arrangement. Do not touch the terminals while power is being supplied.
2. To reduce electro magnetic interference, use wire with adequate rating and twists of the same of equal size shall be made with shortest connection. 3. Cable used for connection to power source, must have a cross section of 1mm or greater. These wires should have insulations capacity made of at least 1.5kV. 4. A better anti-noise effect can be expected by using standard power supply cable for the instrument.
INSTALLATION GUIDELINES
1. This equipment, being built-in-type, normally becomes a part of main control panel and in such case the terminal do not remain accessible to the end user after installation and internal wiring. 2. Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator. 3. Circuit breaker or mains switch must be installed between power source and supply terminal to facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be installed at convenient place normally accessible to the operator. 4. Use and store the instrument within the specified ambient temperature and humidity ranges as mentioned in this manual.
MECHANICAL INSTALLATION GUIDELINES
1. Prepare the panel cutout with proper dimensions as shown above. 2. Fit the unit into the panel with the help of clamp given. 3. The equipment in its installed state must not come in close proximity to any heating source, caustic vapors, oil steam, or other unwanted process byproducts. 4. Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the screws on the terminal block using the tightening torque of the range of 1.2 N.m. 5. Do not connect anything to unused terminals.
MAINTENANCE
1. The equipment should be cleaned regularly to avoid blockage of ventilating parts. 2. Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any other cleaning agent.3. Fusible resistor must not be replaced by operator. Page 2