Page 4
1. Prepare the panel cutout with proper dimensions as show
above.
2. Fit the unit into the panel with the help of clamp given.
3. The equipment in its installed state must not come in close
proximity to any heating source, caustic vapors, oils steam,
or other unwanted process by products.
4. Use the specified size of crimp terminal (M3.5 screws) to
wire the terminal block. Tightening the screws on the
terminal block using the tightening torque of the range of
1.2 N.m.
5. Do not connect anything to unused terminals.
All safety related codifications, symbols and instructions
that appear in this operating manual or on the equipment must
be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
WARNING : Risk of electric shock.
1. To prevent the risk of electric shock power supply to the
equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
being supplied.
2. To reduce electro magnetic interference, use wire with adequate
rating and twists of the same of equal size shall be made with
shortest connection.
3. Cable used for connection to power source, must have a cross
section of 1mm or greater. These wires should have insulations
capacity made of at least 1.5kV.
4. A better anti-noise effect can be expected by using standard
power supply cable for the instrument.
R
Y
S1
S1
S2
S2
3 Phase - 4Wire
R
Y
S1
S1
S2
S2
3 Phase - 3Wire
S1 S2
1 Phase - 2Wire
Read complete instructions prior to installation
and operation of the unit.
WARNING : Risk of electric shock.
If all the equipment is not handled in a manner specified
by the manufacturer, it might impair the protection provided
by the equipment.
B
N
S1 S2
B
Y
R
B
S1 S2
B
Y
R
N
L
Note:
Specifications are subject to change, since development is a continuous process,
So for more updated operating information and Support,
Please contact our Helpline: +91-9081078683/81 or
1. The equipment should be cleaned regularly to avoid blockage
of ventilating parts.
2. Clean the equipment with a clean soft cloth. Do not use
isopropyl alcohol or any other cleaning agent.
3. Fusible resistor must not be replaced by operator.
Outline Dimension (mm) Panel Cutout
Dimension (mm)
92
92
96
96
54
3
L1
L2
L3
A KA Avg
VLL
VLN
Hz
PS
Scroll
AVF 133
SET
AVF 133
S1S1
S1
S2S2
S2
L1L2
L3
L N
1 2 3 4 78910
56
20 19 18 17 14 13 12 11
16 15
!
100
270V AC
~
50/60 Hz
4VA
VL1VL2VL3N
CAT III
Made in India (L-L): 50-550V AC
(L-N): 30-320V AC
Voltage:
Current: 0.5 To 5A AC
www.multispanindia.com
CT Selection:
5/5 to 9999/5
3Ø-4W / 3Ø-3W / 1Ø-2W
System:
Accuracy Class: 0.5
S1S1
S1
S2S2
S2
L1L2
L3
L N
1 2 3 4 78910
56
20 19 18 17 14 13 12 11
16 15
!
100
270V AC
~
50/60 Hz
4VA
VL1VL2VL3N
CAT III
Made in India (L-L): 50-550V AC
(L-N): 30-320V AC
Voltage:
Current: 0.5 To 5A AC
www.multispanindia.com
CT Selection:
5/5 to 9999/5
3Ø-4W / 3Ø-3W / 1Ø-2W
System:
Accuracy Class: 0.5
S1S1
S1
S2S2
S2
L1L2
L3
L N
1 2 3 4 78910
56
20 19 18 17 14 13 12 11
16 15
!
100
270V AC
~
50/60 Hz
4VA
VL1VL2VL3N
CAT III
Made in India (L-L): 50-550V AC
(L-N): 30-320V AC
Voltage:
Current: 0.5 To 5A AC
www.multispanindia.com
CT Selection:
5/5 to 9999/5
3Ø-4W / 3Ø-3W / 1Ø-2W
System:
Accuracy Class: 0.5
WIRING DIAGRAMMECHANICAL INSTALLATION GUIDELINES
WARNING GUIDELINES
MAINTENANCE
SAFETY PRECAUTION
!
