Multitech MTC-MAT1-B01 User manual

MultiConnect®Cell
MTC Cat M1 User Guide

MULTICONNECT CELL SERIES 100 USER GUIDE
2 MultiConnect®Cell MTC Cat M1 User Guide
MultiConnect Cell Series 100 User Guide
Model: MTC-MAT1, MTC-MVW1
Part Number: S000611 1.2
Copyright
This publication may not be reproduced, in whole or in part, without the specific and express prior written permission signed by an executive officer of
Multi-Tech Systems, Inc. All rights reserved. Copyright © 2018 by Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranties, whether express, implied or by estoppels, with respect to the content, information,
material and recommendations herein and specifically disclaims any implied warranties of merchantability, fitness for any particular purpose and non-
infringement.
Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of
Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.
Trademarks
MultiTech®, the Multi Tech logo, and MultiConnect are registered trademarks of Multi-Tech Systems, Inc. All other brand and product names are
trademarks or registered trademarks of their respective companies.
Legal Notices
The MultiTech products are not designed, manufactured or intended for use, and should not be used, or sold or re-sold for use, in connection with
applications requiring fail-safe performance or in applications where the failure of the products would reasonably be expected to result in personal injury or
death, significant property damage, or serious physical or environmental damage. Examples of such use include life support machines or other life
preserving medical devices or systems, air traffic control or aircraft navigation or communications systems, control equipment for nuclear facilities, or
missile, nuclear, biological or chemical weapons or other military applications (“Restricted Applications”). Use of the products in such Restricted
Applications is at the user’s sole risk and liability.
MULTITECH DOES NOT WARRANT THAT THE TRANSMISSION OF DATA BY A PRODUCT OVER A CELLULAR COMMUNICATIONS NETWORK WILL BE
UNINTERRUPTED, TIMELY, SECURE OR ERROR FREE, NOR DOES MULTITECH WARRANT ANY CONNECTION OR ACCESSIBILITY TO ANY CELLULAR
COMMUNICATIONS NETWORK. MULTITECH WILL HAVE NO LIABILITY FOR ANY LOSSES, DAMAGES, OBLIGATIONS, PENALTIES, DEFICIENCIES, LIABILITIES,
COSTS OR EXPENSES (INCLUDING WITHOUT LIMITATION REASONABLE ATTORNEYS FEES) RELATED TO TEMPORARY INABILITY TO ACCESS A CELLULAR
COMMUNICATIONS NETWORK USING THE PRODUCTS.
Contacting MultiTech
Knowledge Base
The Knowledge Base provides immediate access to support information and resolutions for all MultiTech products. Visit http://www.multitech.com/kb.go.
Support Portal
To create an account and submit a support case directly to our technical support team, visit: https://support.multitech.com.
Support
Business Hours: M-F, 8am to 5pm CT
Country By Email By Phone
Europe, Middle East, Africa: [email protected] +(44) 118 959 7774
U.S., Canada, all others: [email protected] [phone] or [phone]
Warranty
To read the warranty statement for your product, visit www.multitech.com/warranty.go. For other warranty options, visit www.multitech.com/es.go.
World Headquarters
Multi-Tech Systems, Inc.
2205 Woodale Drive, Mounds View, MN 55112
Phone: [phone] or [phone]
Fax [phone]

CONTENTS
MultiConnect®Cell MTC Cat M1 User Guide 3
Contents
Chapter 1 – Product Overview ................................................................................................................................. 5
About the MultiConnect Cell Modem........................................................................................................................... 5
Documentation ........................................................................................................................................................... 5
Product Build Options ................................................................................................................................................... 5
Package Contents ......................................................................................................................................................... 6
Dimensions.................................................................................................................................................................... 7
Serial............................................................................................................................................................................ 7
USB.............................................................................................................................................................................. 8
Descriptions of LEDs...................................................................................................................................................... 9
Side Panels .................................................................................................................................................................. 10
MTC-MAT1 Specifications ........................................................................................................................................... 10
MTC-MVW1 Specifications.......................................................................................................................................... 11
RS-232 9-Pin Female Connector ................................................................................................................................. 13
Power Measurements................................................................................................................................................. 13
Serial Model: MTC-MAT1 Power Draw..................................................................................................................... 13
MTC-MVW1 Power Draw.......................................................................................................................................... 14
Chapter 2 – Carrier Specific Notice ......................................................................................................................... 16
Firmware Over the Air (FOTA) Script .......................................................................................................................... 16
Verizon Requirement: Firmware Over The Air (FOTA) - Scripting ............................................................................ 16
Cellular Module FOTA Script Example Process ......................................................................................................... 16
FOTA Client Example Session Log ............................................................................................................................. 18
Chapter 3 – Safety Warnings.................................................................................................................................. 20
Radio Frequency (RF) Safety ....................................................................................................................................... 20
Interference with Pacemakers and Other Medical Devices ...................................................................................... 20
Potential interference............................................................................................................................................... 20
Precautions for pacemaker wearers ........................................................................................................................ 20
Antenna....................................................................................................................................................................... 21
Chapter 4 – Installing and Using the Device ........................................................................................................... 22
Installing the Device.................................................................................................................................................... 22
Placing Serial Devices in Power Save Mode.............................................................................................................. 22
Powering Down Your Device ...................................................................................................................................... 23
Applications with Risk of Power Surge ....................................................................................................................... 23
Installing a SIM Card ................................................................................................................................................... 23
Removing a SIM Card................................................................................................................................................ 23
Mounting Device to Flat Surface................................................................................................................................. 24
Chapter 5 – Antenna and Activation Information................................................................................................... 25
Antenna....................................................................................................................................................................... 25

CONTENTS
4 MultiConnect®Cell MTC Cat M1 User Guide
Antenna System Cellular Devices................................................................................................................................ 25
LTE Cat M1 Antenna.................................................................................................................................................... 25
Antenna Specifications ............................................................................................................................................. 25
Account Activation for Cellular Devices ..................................................................................................................... 26
Device Phone Number ................................................................................................................................................ 26
Adding APN value (MAT1 only)................................................................................................................................... 26
Chapter 6 – Configuring and Communicating with Your Device.............................................................................. 27
Before Using the Device.............................................................................................................................................. 27
Using Command Mode and Online Data Mode.......................................................................................................... 27
Verifying Signal Strength............................................................................................................................................. 27
Example .................................................................................................................................................................... 28
Checking Network Registration................................................................................................................................... 28
Sending and Receiving Data for MAT1 ....................................................................................................................... 29
Connecting Device to TCP Server as TCP Client........................................................................................................ 29
Configuring Device as UDP Listener to Accept UDP Client Connections ................................................................. 29
Configuring Device as UDP Client to Connect to UDP Server ................................................................................... 30
Transferring FTP File to FTP Server ........................................................................................................................... 31
Downloading File from FTP Server............................................................................................................................ 32
Sending and Receiving Data for MVW1 ...................................................................................................................... 33
Connecting Device to TCP Server as TCP Client........................................................................................................ 33
Configuring Device as UDP Listener to Accept UDP Client Connections ................................................................. 34
Configuring Device as UDP Client to Connect to UDP Server ................................................................................... 35
Transferring FTP File to FTP Server ........................................................................................................................... 36
Downloading File from FTP Server............................................................................................................................ 37
Reading, Writing and Deleting Messages ................................................................................................................... 38
Reading Text Messages............................................................................................................................................. 38
Writing Text Messages.............................................................................................................................................. 38
Deleting Messages .................................................................................................................................................... 39
Chapter 7 – Regulatory Information....................................................................................................................... 40
Industry Canada Class B Notice................................................................................................................................... 40
Industry Canada and FCC ............................................................................................................................................ 40
47 CFR Part 15 Regulation Class B Devices ............................................................................................................... 40
FCC Interference Notice............................................................................................................................................ 41
Restriction of the Use of Hazardous Substances (RoHS) ............................................................................................ 41
Information on HS/TS Substances According to Chinese Standards ......................................................................... 42
Information on HS/TS Substances According to Chinese Standards (in Chinese) ...................................................... 43

PRODUCT OVERVIEW
MultiConnect®Cell MTC Cat M1 User Guide 5
Chapter 1 – Product Overview
About the MultiConnect Cell Modem
MultiConnect Cell 100 Series MTC Cat M1 cellular modems are ready-to-deploy, standalone LTE UE Category M1
modems that provide wireless communication. The MTC Cat M1 is a compact communications platform that
provides cellular capabilities for fixed and mobile applications. The device provides low-powered option specifically
designed for IOT applications that collect smaller amounts of data or with less frequency. This product is available
with RS-232 or USB connectors.
Documentation
This documentation is available on the MultiTech Installation Resources website at www.multitech.com/support.
Document Description
MultiConnect Cell MTC Cat
M1 User Guide
This document provides an overview, safety and regulatory information, schematics,
and general device information, P/N S000611.
USB Driver Installation Guide Instructions for installing USB drivers on Linux and Windows Systems, P/N S000616.
Telit ME910C1 AT
Commands Reference Guide
Lists AT Commands and parameters used to configure your device, P/N
80529ST10815A Rev.2.
Product Build Options
Product Description Carrier/Region
MTC-MAT1-B01 LTE UE Category M1 Modem (Serial version) AT&T/NA
MTC-MAT1-B01-US* LTE UE Category M1 Modem (Serial version)+ Kit AT&T/NA
MTC-MAT1-B03 LTE UE Category M1 Modem (USB version) AT&T/NA
MTC-MAT1-B03-KIT* LTE UE Category M1 Modem (USB version)+ Kit AT&T/NA
MTC-MVW1-B01 LTE UE Category M1 Modem (Serial version) Verizon/NA
MTC-MVW1-B01-US* LTE UE Category M1 Modem (Serial version)+ Kit Verizon/NA
MTC-MVW1-B03 LTE UE Category M1 Modem (USB version) Verizon/NA

PRODUCT OVERVIEW
6 MultiConnect®Cell MTC Cat M1 User Guide
Product Description Carrier/Region
MTC-MVW1-B03-KIT* LTE UE Category M1 Modem (USB version)+ Kit Verizon/NA
*Note: Kits include cellular antenna and other accessories with the specified product.
Package Contents
Your MTC Cat M1 package typically includes the following:
Contents Description
1 - Power Supply with Removable Blades (serial version) OR
1 - USB cable (USB version)
1 - RS-232 cable 6-ft. (serial version)
1 - Cellular Antenna
Document MTC Cat M1 Quick Start Guide
1 - Mounting Tab and Bracket
4 - Rubber Feet
Note: The above information does not apply purchasing the device only.

PRODUCT OVERVIEW
MultiConnect®Cell MTC Cat M1 User Guide 7
Dimensions
Serial

PRODUCT OVERVIEW
8 MultiConnect®Cell MTC Cat M1 User Guide
USB

PRODUCT OVERVIEW
MultiConnect®Cell MTC Cat M1 User Guide 9
Descriptions of LEDs
The top panel contains the following LEDs:
Power and Terminal Ready LEDs—The Power LED indicates that DC power is present and the TR LED blinks
when the unit is functioning normally.
Modem LEDs—Two modem LEDs indicate carrier detection and link status (for serial units only).
Prog. Signal LEDs—Three programmable signal LEDs can display the signal strength level of the wireless
connection if coded by the user.
LED Indicators
POWER Indicates presence of DC power when lit.
TR Terminal Ready. When lit, indicates connection to terminal emulation. When not lit,
indicates no terminal is present.
(for serial only)
CD Carrier Detect. Indicates established data connection when lit.
(for serial only)
PROG. SIGNAL These LEDs do not function by default and require the user to write code in order to
control them. If programmed, they display the strength of the cellular signal.
Note: The three PROG. SIGNAL LEDs can be controlled as follows:
GPIO2: Controls the LED with a single bar above it
GPIO3: Controls the LED with two bars above it
GPIO4: Controls the LED with three bars above it
For more information on using GPIO to control the LEDs, review the AT Command
Guide.

PRODUCT OVERVIEW
10 MultiConnect®Cell MTC Cat M1 User Guide
Side Panels
The device has connectors on either side. The figures that follow show the side panels.
MTC-MAT1 Specifications
Category Description
General
Standards LTE UE Category M1
3GPP release 13
USB 2.0 HS / Serial port multiplexer 3GPP TS27.010
TCP/IP Functions FTP, SMTP, SSL, TCP, UDP, TLS
Frequency Bands 4G: 700 (B12)/AWS 1700 (B4)/1900 (B2)
Speed
Data Speed LTE Category M1: 300 kbps downlink/375 kbps uplink
Interface
USB Interface USB 2.0 high speed compatible
UART Interface RS-232 levels
Physical Description
Weight 0.4 oz. (10 g)
Dimensions Refer to mechanical drawing for dimensions.
Connectors
Antenna Connector 1 surface mount SMA connector for cellular
SIM 1.8V and 3V SIM holder for mini-SIM card

PRODUCT OVERVIEW
MultiConnect®Cell MTC Cat M1 User Guide 11
Category Description
Environment
Operating Temperature -40° C to +85° C
Storage Temperature -40° C to +85° C
Humidity 20%-90% RH, non-condensing
Power Requirements
Operating Voltage Serial Models: 5-32 VDC
USB Models: 5 VDC
Category Description
SMS
SMS Point-to-Point messaging
Mobile-Terminated SMS
Mobile-Originated SMS
Certifications and Compliance
EMC Compliance FCC Part 15 Class B
Radio Compliance FCC Part 24, 27
Safety Compliance UL 60950-1 2nd ED
cUL 60950-1 2nd ED
IEC 60950-1 2nd ED
Network Compliance PTCRB
Carrier AT&T
MTC-MVW1 Specifications
Category Description
General
Standards LTE UE Category M1
3GPP Release 13
USB 2.0 HS / Serial port multiplexer 3GPP TS27.010
TCP/IP Functions FTP, SMTP, SSL, TCP, UDP, TLS
Frequency Band 4G: 700 MHz (B13)/AWS 1700 (B4)
Speed
Data Speed LTE Category M1: 300 kbps downlink/375 kbps uplink
Interface
USB Interface USB 2.0 high speed compatible

PRODUCT OVERVIEW
12 MultiConnect®Cell MTC Cat M1 User Guide
Category Description
UART Interface RS-232 levels
Physical Description
Weight 0.4 oz. (10 g)
Dimensions Refer to mechanical drawing for dimensions.
Connectors
Antenna Connector 1 surface mount SMA connector for cellular
SIM 1.8V and 3V SIM holder for mini-SIM card
Category Description
Environment
Operating Temperature -40° C to +85° C
Storage Temperature -40° C to +85° C
Humidity 20%-90% RH, non-condensing
Power Requirements
Voltage Serial Models: 5-32 VDC
USB Models: 5 VDC
SMS
SMS Point-to-Point messaging
Mobile-Terminated SMS
Mobile-Originated SMS
Certifications and Compliance
EMC Compliance FCC Part 15 Class B
Radio Compliance FCC Part 24, 27
Safety Compliance UL 60950-1 2nd ED
cUL 60950-1 2nd ED
IEC 60950-1 2nd ED
Carrier Verizon

PRODUCT OVERVIEW
MultiConnect®Cell MTC Cat M1 User Guide 13
RS-232 9-Pin Female Connector
Pin Abbreviation Description In/Out
1 CD Carrier Detect O
2 RX Receive O
3 TX Transmit I
4 DTR Data Terminal Ready I
5 GND Ground --
6 DSR Data Set Ready O
7 RTS Request to Send I
8 CTS Clear to Send O
9 RI Ring Indicator O
Power Measurements
Multi-Tech Systems, Inc. recommends incorporating a 10% buffer into your power source when determining
product load.
Serial Model: MTC-MAT1 Power Draw
Serial model (B01)
Radio
protocol
Sleep
mode
(mA)1
Power save
mode (mA)
Live idle
(mA)2
No data
(mA)3
Max power
(mA)4
TX pulse
(mA) 5
Inrush
charge
(mC)6
Inrush
duration
(ms)7
9 Volts
LTE 1900
MHz
9 7 26 42 84 152 0.756 9.56
12 Volts
LTE 1900
MHz
7 6 24 34 67 136 0.743 7.53
24 Volts
LTE 1900
MHz
5 4 15 24 45 116 1.32 15.4

PRODUCT OVERVIEW
14 MultiConnect®Cell MTC Cat M1 User Guide
USB model (B03)
Radio
protocol
Sleep mode
(mA)1
Power save
mode (mA)
Live idle
(mA)2
No data
(mA)3
Max power
(mA)4
TX pulse
(mA) 5
Inrush charge
(mC)6
5 Volts
LTE N/A 6 36 35 125 212 0.596
Note:
1Sleep mode: Sleep mode current, connected to wireless (milliamps).
2Live idle: Live Connection Idle Current (milliamps).
3No data: Cellular call box connection, no data (milliamps).
4Max Power: Average measured current (milliamps) at maximum power. The continuous current during
maximum data rate with the radio transmitter at maximum power.
5TX pulse: Average TX pulse amplitude current (milliamps). The average peak current during a transmission
burst period.
6Inrush charge: Total inrush charge (millicoulombs). The total inrush charge or input current at power up, or
reset.
7Inrush duration: Total inrush charge duration during power-up (milliseconds).
MTC-MVW1 Power Draw
Serial model (B01)
Radio
protocol
Sleep
mode
(mA)1
Power save
mode (mA)
Live idle
(mA)2
No data
(mA)3
Max power
(mA)4
TX pulse
(mA) 5
Inrush
charge
(mC)6
Inrush
duration
(ms)7
9 Volts
LTE 700
MHz
9 20 26 25 70 132 0.762 9.0
12 Volts
LTE 700
MHz
7 19 24 24 58 124 0.768 7.4
24 Volts
LTE 700
MHz
4 10 14 14 41 108 1.16 23.0

PRODUCT OVERVIEW
MultiConnect®Cell MTC Cat M1 User Guide 15
USB model (B03)
Radio
protocol
Sleep mode
(mA)1
Power
save mode
(mA)
Live idle (mA)2No data
(mA)3
Max power
(mA)4
TX pulse
(mA) 5
Inrush charge
(mC)6
5 Volts
LTE N/A 6 36 35 125 212 0.596
Note:
1Sleep mode: Sleep mode current, connected to wireless (milliamps).
2Live idle: Live Connection Idle Current (milliamps).
3No data: Cellular call box connection, no data (milliamps).
4Max Power: Average measured current (milliamps) at maximum power. The continuous current during
maximum data rate with the radio transmitter at maximum power.
5TX pulse: Average TX pulse amplitude current (milliamps). The average peak current during a transmission
burst period.
6Inrush charge: Total inrush charge (millicoulombs). The total inrush charge or input current at power up, or
reset.
7Inrush duration: Total inrush charge duration during power-up (milliseconds).

CARRIER SPECIFIC NOTICE
16 MultiConnect®Cell MTC Cat M1 User Guide
Chapter 2 – Carrier Specific Notice
Firmware Over the Air (FOTA) Script
Verizon Requirement: Firmware Over The Air (FOTA) - Scripting
At times, your device may require a critical update to radio firmware for devices connecting to the network. To
stay compliant to Verizon’s LTE requirements you must implement FOTA. Failure to perform a critical update could
result in losing access to the Verizon network.
MultiTech has developed a script for customers to use in order to initiate a FOTA update from the (the customer’s)
local host processor (pull FOTA).
In an upcoming release, MultiTech LTE Category M1, devices for Verizon, will allow the customer to initiate a FOTA
update from a remote server (push FOTA) as required and communicated by Verizon.
If your device does not include local processing capabilities, you will be required to upgrade when that release
becomes available.
Below is an example of a FOTA process for the ME910C1-NV cellular module you could implement in your host
system. You may implement the process below or implement your own FOTA solution.
In the example below, your host system application periodically accesses a file placed on an FTP server of your
choosing and reads file contents to determine if a firmware update is required.
Cellular Module FOTA Script Example Process
1. Set up an FTP server to contain a folder for future module firmware files.
2. Assign a unique username/password to access the FTP server.
3. Create and place a file on your FTP server named firmwarecheck.csv to be downloaded and read by
ME910C1-NV FTP client host application. Include the following types of information in the file. You can
include additional information as needed.
a. The firmware version and build your ME910C1-NV device should currently be using.
b. Path on current FTP server where firmware update file resides.
c. The date/time interval at which the host application should next perform a FOTA check in.
d. FTP server IP address which the host application should access during next FOTA check in.
e. Credentials for the FTP server where host application should next perform a FOTA check in.
4. Before deploying devices with an ME910C1-NV, create code in the host system code to perform the
following sequence at a defined interval (nightly, weekly, daily, monthly).
a. Issue following command to Telit ME910C1-NV to configure socket connection settings:
AT#SCFG=1,3,300,90,600,50
b. If data APN has not previously been programmed, issue the following command:
AT+CGDCONT=3,"IPV4V6","CorrectAPNForAccount"
If the data APN has been previously programmed, go to Step 4.c.
c. Issue the following command to check for signal presence:
AT+CSQ
d. Issue the following command to check for registration presence:

CARRIER SPECIFIC NOTICE
MultiConnect®Cell MTC Cat M1 User Guide 17
AT+CEREG?
e. If signal and registration are present, issue the following command to establish data connection:
AT#SGACT=3,1
If signal and registration are not present, check antenna for proper connection and SIM for correct
orientation.
f. Issue following command to create FTP session:
AT#FTPOPEN="204.26.122.49","username","password",1,3
g. Have the host application issue the following command to download the firmwarecheck.csv file, read
its contents, and take actions based on those contents:
AT#FTPGET="firmwarecheck.csv
h. Have host system issue the following command to Telit ME910C1-NV to determine current firmware
file version and firmware build:
AT+GMR
AT#CFVR
i. If version/build indicated in responses are the same as indicated in firmwarecheck.csv: Go to Step
4.s.
j. If current firmware version is older than version indicated in firmwarecheck.csv: Continue to next
step.
k. Issue the following command to Telit ME910C1-NV to download the file indicated in the
firmwarecheck.csv file and wait for OK response (which indicates the file has been downloaded):
AT#FTPGETOTA="Name-Of-Firmware-File-Here.bin",0
l. After file is downloaded issue following command to Telit ME910C1-NV to close FTP session:
AT#FTPCLOSE
m. After closing FTP, issue following command to Telit ME910C1-NV to disconnect data session:
AT#SGACT=3,0
n. After closing data session, issue following command to Telit ME910C1-NV to apply downloaded file:
AT#OTAUP=0
o. Before continuing, wait for ME910C1-NV to reset a total of three times and/or wait a fixed period of
time to ensure module has enough time to apply downloaded firmware. The time needed varies
depending on the size of your firmware file.
p. Issue the following command to Telit ME910C1-NV to determine current firmware version.
AT+GMR
q. If version matches value indicated in firmwarecheck.csv: Go to Step 4.t.
If version does not match value indicated in firmwarecheck.csv issue, appropriate commands listed
earlier as needed in order to attempt to download and process the firmware file again.
r. Issue following command to Telit ME910C1-NV to close FTP session:
AT#FTPCLOSE
s. Issue following command to Telit ME910C1-NV to close data session:
AT#SGACT=3,0
t. End Process
Note:
Before deploying the device, thoroughly test your chosen FOTA implementation for functionality.

CARRIER SPECIFIC NOTICE
18 MultiConnect®Cell MTC Cat M1 User Guide
Before performing any module firmware update to devices in the field, first thoroughly test the new
module firmware to ensure compatibility with your existing application.
In the above example you might consider placing on the FTP server one file for every IMEI you
deploy. Then have host application read module IMEI to determine which IMEI file on the FTP server
to read. This would allow you to control which specific IMEIs you want to update by changing the
contents of the file on server for the device IMEI.
FOTA Client Example Session Log
Example of updated from firmware version 30.00.001-B026 to version 30.00.001-B026_FOTA
[Tue Jan 09 13:18:18.344 2018] AT+GMM
[Tue Jan 09 13:18:18.437 2018] ME910C1-NV
[Tue Jan 09 13:18:18.437 2018]
[Tue Jan 09 13:18:18.437 2018] OK
[Tue Jan 09 13:18:18.952 2018] AT+GMR
[Tue Jan 09 13:18:19.046 2018] 30.00.001-B026
[Tue Jan 09 13:18:19.046 2018]
[Tue Jan 09 13:18:19.046 2018] OK
[Tue Jan 09 13:18:19.560 2018] AT#SCFG=1,3,300,90,600,50
[Tue Jan 09 13:18:19.950 2018] OK
[Tue Jan 09 13:18:20.465 2018] AT+CGDCONT=3,"IPV4V6","VZWINTERNET"
[Tue Jan 09 13:18:21.120 2018] OK
[Tue Jan 09 13:18:21.635 2018] AT+CSQ
[Tue Jan 09 13:18:21.729 2018] +CSQ: 25,3
[Tue Jan 09 13:18:21.729 2018]
[Tue Jan 09 13:18:21.729 2018] OK
[Tue Jan 09 13:18:22.243 2018] AT+CEREG?
[Tue Jan 09 13:18:22.384 2018] +CEREG: 0,1
[Tue Jan 09 13:18:22.384 2018]
[Tue Jan 09 13:18:22.384 2018] OK
[Tue Jan 09 13:18:22.899 2018] AT#SGACT=3,1
[Tue Jan 09 13:18:23.101 2018] #SGACT:
100.82.36.41,38.0.16.20.176.102.243.25.0.0.0.2.116.124.129.1
[Tue Jan 09 13:18:23.101 2018]
[Tue Jan 09 13:18:23.101 2018] OK
[Tue Jan 09 13:18:23.616 2018]
AT#FTPOPEN="204.26.122.49","USERNAME","PASSWORD",1,3
[Tue Jan 09 13:18:24.942 2018] OK
[Tue Jan 09 13:18:25.457 2018] AT#FTPGET="firmwarecheck.csv"
[Tue Jan 09 13:18:26.159 2018] CONNECT
[Tue Jan 09 13:18:26.237 2018] 30.00.001-B026_FOTA,30.00.001-
B026_FOTA.bin,2017-01-31,204.26.122.49,USERNAME,PASSWORD
[Tue Jan 09 13:18:26.253 2018] NO CARRIER
[Tue Jan 09 13:18:26.767 2018] AT+GMR
[Tue Jan 09 13:18:26.861 2018] 30.00.001-B026
[Tue Jan 09 13:18:26.861 2018]
[Tue Jan 09 13:18:26.861 2018] OK
[Tue Jan 09 13:18:27.742 2018] AT#CFVR
[Tue Jan 09 13:18:27.750 2018] #CFVR: 1
[Tue Jan 09 13:18:27.750 2018]
[Tue Jan 09 13:18:27.750 2018] OK

CARRIER SPECIFIC NOTICE
MultiConnect®Cell MTC Cat M1 User Guide 19
[Tue Jan 09 13:18:32.430 2018] AT#FTPGETOTA="30.00.001-B026_to_B026-
FOTA.bin",0
[Tue Jan 09 13:18:37.001 2018] OK
[Tue Jan 09 13:18:37.516 2018] AT#FTPCLOSE
[Tue Jan 09 13:18:37.843 2018] OK
[Tue Jan 09 13:18:38.358 2018] AT#SGACT=3,0
[Tue Jan 09 13:18:38.545 2018] OK
[Tue Jan 09 13:18:39.060 2018] AT#OTAUP=0
[Tue Jan 09 13:18:39.388 2018] OK
[Tue Jan 09 13:21:23.977 2018] AT+GMR
[Tue Jan 09 13:21:27.456 2018] 30.00.001-B026_FOTA
[Tue Jan 09 13:21:27.456 2018]

SAFETY WARNINGS
20 MultiConnect®Cell MTC Cat M1 User Guide
Chapter 3 – Safety Warnings
Radio Frequency (RF) Safety
Due to the possibility of radio frequency (RF) interference, it is important that you follow any special regulations
regarding the use of radio equipment. Follow the safety advice given below.
Operating your device close to other electronic equipment may cause interference if the equipment is
inadequately protected. Observe any warning signs and manufacturers’ recommendations.
Different industries and businesses restrict the use of cellular devices. Respect restrictions on the use of
radio equipment in fuel depots, chemical plants, or where blasting operations are in process. Follow
restrictions for any environment where you operate the device.
Do not place the antenna outdoors.
Switch OFF your wireless device when in an aircraft. Using portable electronic devices in an aircraft may
endanger aircraft operation, disrupt the cellular network, and is illegal. Failing to observe this restriction
may lead to suspension or denial of cellular services to the offender, legal action, or both.
Switch OFF your wireless device when around gasoline or diesel-fuel pumps and before filling your vehicle
with fuel.
Switch OFF your wireless device in hospitals and any other place where medical equipment may be in use.
Interference with Pacemakers and Other Medical Devices
Potential interference
Radio frequency energy (RF) from cellular devices can interact with some electronic devices. This is
electromagnetic interference (EMI). The FDA helped develop a detailed test method to measure EMI of implanted
cardiac pacemakers and defibrillators from cellular devices. This test method is part of the Association for the
Advancement of Medical Instrumentation (AAMI) standard. This standard allows manufacturers to ensure that
cardiac pacemakers and defibrillators are safe from cellular device EMI.
The FDA continues to monitor cellular devices for interactions with other medical devices. If harmful interference
occurs, the FDA will assess the interference and work to resolve the problem.
Precautions for pacemaker wearers
If EMI occurs, it could affect a pacemaker in one of three ways:
Stop the pacemaker from delivering the stimulating pulses that regulate the heart's rhythm.
Cause the pacemaker to deliver the pulses irregularly.
Cause the pacemaker to ignore the heart's own rhythm and deliver pulses at a fixed rate.
Based on current research, cellular devices do not pose a significant health problem for most pacemaker wearers.
However, people with pacemakers may want to take simple precautions to be sure that their device doesn't cause
a problem.
Keep the device on the opposite side of the body from the pacemaker to add extra distance between the
pacemaker and the device.
Avoid placing a turned-on device next to the pacemaker (for example, don’t carry the device in a shirt or
jacket pocket directly over the pacemaker).