Multitek VIP70 User manual

MULTITEK IP INTERCOM ROOM MONITOR INSTALLATION AND SHORT USER MANUAL
(VIP70, VIP71, VIP72, VIP74, VIP100, VIP101, VIP100 DELUX, VIP102)
It obeys the rules of AEEE regulations.

2
TABLE OF CONTENTS
1. PRODUCT DESCRIPTION.........................................................................................................4
2. BRIEF FEATURES.....................................................................................................................4
3. PACKAGE CONTENTS .............................................................................................................4
4. SAFETY INSTRUCTIONS ..........................................................................................................4
5. INSTALLLATION......................................................................................................................4
6. TROUBLE SHOOTING..............................................................................................................5
7. IP MONITOR SHORT USER MANUAL ......................................................................................6
7.1. Allocating Ip Number To Room Monitors ........................................................................7
7.2. Smart Home Relay Application..........................................................................................9
7.3. Smart Home Rf Application .............................................................................................15
7.4. Smart Home Knx System..................................................................................................20
7.5. Adding Rooms And Devices .............................................................................................21
8. IP DOOR PANEL SHORT USER MANUAL ...............................................................................34
8.1. Allocating Ip Number To Ip Door Panels (For Dip40) ....................................................34
8.2. Calling The Rooms From The Door Panel .......................................................................35
8.3. Calling The Guard And The Doorkeeper From The Panel..............................................36
8.4. Phone Book Feature Of The Door Panel ........................................................................37
8.5. Open The Door By Entering Password ...........................................................................38

IP INTERCOM SHORT USER MANUAL
Thank you for choosing Multitek ip intercom room monitor. This user manual was prepared for using the device
more efficiently.
MULTITEK IP INTERCOM ROOM MONITOR WARRANTY FOR 2 YEARS AGAINST MANUFACTURING DEFECTS.
Multitelk has rights to change the features of the device given in this document prior given any information.
Manufacturer: Multitek Elektronik San. Ve Tic. A. Ş.
Headquarter / Factory: Meclis Mahallesi Atatürk Cad. No: 47 34785 Sancaktepe / İSTANBUL
Tel: [phone] Faks: (0216) 415 79 18
E-Mail: [e-mail]

1. PRODUCT DESCRIPTION
MULTITEK IP MONITOR is a color video door phone set; used to monitor, call, intercom and open the door locks.
This product set can be used in villas, single houses, apartments, hotels, offices etc. giving the user benefits of
security and convenience.
The device has optional alarm and smart home features.
2. BRIEF FEATURES
There is no limit in number of monitors that can be connected to the IP intercom network. All rooms
have intercom features in between monitors and outdoor panels.
Each monitor can talk to door panel and open the door(s)
Devices have various additional features described in the short user manual and soft manual.
3. PACKAGE CONTENTS
A basic set contains:
A room monitor with 7” or 10” LCD with different hardware designs.
A socket for indoor ring, optional sockets for the alarm and smart home features.
4. SAFETY INSTRUCTION
Keep the indoor unit away from high temperature (i.e. near an oven, under direct sunlight, high humidity
such as bathroom and greenhouse)
Do not install the indoor unit close to a television or expose strong jamming. TV and the intercom can
interfere with each other.
Do not touch the unit with wet hands.
Avoid throwing, dropping or hitting the units.
Clean the camera or screen with a soft cloth. Do not use detergent, thinner, volatile or corrosive liquids.
Use the product under the circumstance of barrier-free and no interference.
5. INSTALLATION
Please follow the below steps for installation.
Install the room monitor to the wall by using the screws and dowels with the wall bracket. The device
should be installed to the height where the screen is monitored easily. Insert RJ45 plug with CAT6 cable
to the RJ45 socket located on the back of the monitor.
It takes about 3 minutes boot-up of the devices. See company logo during boot-up on the monitor.
When the device boots-up, the screen is touched, the main menu appears.

6. TROUBLE SHOOTING
Problem
Solutions
No Picture / Signal
Make sure all the connections are secure and properly connected.
Make sure your monitor is plugged into the PoE switch.
Make sure there is nothing obstructing the view of the camera of the
door panel.
No picture,
but
intercommunication
is normal
Make sure all the connections are secure and properly connected.
Make sure there is nothing obstructing the view of the camera
No audio when calling
Make sure the volume notch on the indoor unit is turned off or the
monitor is in silence mode.
Make sure there is nothing interfering with the speaker or microphone
on the indoor unit or the camera.
Make sure all the connections are secure and properly connected
The outdoor unit
cannot call the indoor
monitor
Make sure all the connections are secure and properly connected
There is no power on
the monitor
Check CAT6 cable is connected to the device
Check CAT6 cable is properly crimped to RJ45 socket

6
7. IP MONITOR SHORT USER MANUAL
IP INTERCOM ROOM MONITOR BASIC USER FEATURES
Before powering up the system, please make sure that cabling is correct. Gold-pleated RJ-45 plugs should be
used for best quality.
When power is given to the device, the screen turns on and Multitek intercom application runs in three
minutes. Main screen is shown below:
Figure 1: Sleep screen

7
7.1. Allocating Ip Number To Room Monitors
NOTICE: DEVICE SHOULD BE PROGRAMMED BY THE INSTALLATION TECHNICIAN. TO ASSING A ROOM
NUMBER TO A DEVICE, YOU HAVE TO KNOW THE BLOCK AND ROOM NUMBER OF THE ROOM. NO
ADDITIONAL INFORMATION IS NEEDED.
To assign a block and room number to a device, follow the menu pages below:
MAIN MENU/ SETUP/ System Settings / Device Number
(default keyword to enter systems settings is “0000”)
Figure 2: Main screen
Figure 3: Settings

8
Figure 4: Device Number Settings
When you touch Device Number, you will see the current catalogue number of the device.
However, you will not be able to edit these fields without entering editing mode.
There are two ways to enter editing mode according to type of your device:
Press Volume - button then touch Device Number (flush mount monitors do not have this buttons)
Touch the settings icon located on the right upper corner for 5 seconds, then tap the setting that you
want to update.
Figure 5: Updating Device Number

9
When the new display page appears (you’ll see Android icon on the bottom left), it is possible to edit the
following fields:
Enter Block
Number
Enter two-digit block number
i.e. 01 for Block one or a single block
apartment
Enter Room
Number
Enter three-digit room number
i.e. Enter 005 for room number 5
Enter Device
Number
You can connect up to 3 parallel devices
per room. Enter 1,2 or 3 for this field. If
there is a single device in a room this
value should be “1”.
After completing all fields, tap green check sign icon located on the right of the screen.
After entering all these parameters correctly, the device will restart and run with the new values.
ROOM 1 at BLOCK 1
BLOCK NO: 01 ROOM NO: 001 DEVICE TYPE: 1
ROOM 10 at BLOCK 7
BLOCK NO: 07 ROOM NO: 010 DEVICE TYPE: 1
ROOM 103 at BLOCK 12
BLOCK NO: 12 ROOM NO: 103 DEVICE TYPE: 1
7.2. Smart Home Relay Application
First of all, the “Smart Home” tab is entered from the settings menu. It is saved by selecting Relay (16 relay or 4
relay) from this page. Click ”SMART HOME" in the main menu to open the application.
7.2.1 Add Device
Press setting icon on top right to the add device. Password screen appears to the setting menu.
Default Password: 0000
Figure 6: Add Device

10
The setting page that opens after the password is entered is as follows:
Click on the channels on the page to select which relay is selected.

11
7.2.2. Settings Menu
To access other relay settings, press the icon on the top right.
Figure 7:Settings Menu
7.2.2.1 Alarm Settings
The alarm settings option is selected to add alarms to the relays.
Figure 8:Alarm Settings
Select the desired relay to add alarm. The alarm can only be added to the dual relays. If the relay you select is a
single relay, the following warning screen appears.

12
When you select dual relay, alarm options are opened as below.
Alarms are selected and exit the menu.
7.2.2.2 Favorite Settings
Relay channels to be added to the scenario are added to favorites.
The default value for devices added to Favorites is 1. This value is changed to 0 by pressing the relay icon which
you want.
If the scenario value is 1, the relay pulls in the "In Home" scenario, leaves relay in "Out Home" scenario.
If the scenario value is 0, leaves relay in the "In Home" scenario, the relay pulls in the "Out Home” scenario.
Figure 9:Favorite Settings

13
7.2.2.3 Relay Name
To change the names of the relay channels or to give the name of the relay , enter the relay names tab. Write
the name and left the menu.
CHANGE ICON
CHANGE ICON
CHANGE ICON

14
7.2.2.4 Change Icon
Enter icon change menu to select appropriate icon to channels functions. You can exit the menu by selecting
the appropriate icons for the channels.
7.2.2.5 Setting Time
In the time adjustment category, enter the duration to remain open for the selected channel.
7.2.2.6 Smart Home Relay System
Back to the main menu after the settings have been done. When you enter the smart home page from the
main menu, the screen will be as follows:

15
7.3 Smart Home Rf Application
First of all, the “Smart Home” tab is entered from the settıngs menu. It is saved by selecting RF this page. Click
”SMART HOME" in the main menU (Figure 7.24) to open the application.
Figure 10:Apartment Monitor Main Menu
Figure 11:Rooms Screen
When you open applicaton, rooms screen appears. (Figure 11)
7.3.1 Add Room And Device
Press the settings icon on the top right to the add device. Enter the password (Password: 0000)

16
The room settings screen has the following keys. (Figure 12)
You can add, edit or delete room with this keys.
Press for adding room. “ADD ROOM” screen (Figure 12) appears. You can change room name by click the
box on top right.
9 devices are defined on the device section. These devices are; Blind-R, Blind-M, Dimmer, Lights-R, Lights-M,
HVAC, 4-Button Relay Control, IR and Heat-Cool. Select the device which you want, press on bottom right.
Added device to the Room Devices section.
ADD ROOM
EDIT ROOM
DELETE ROOM
Figure 12:Room Settings Screen

17
Below are the keys on bottom the "ROOM DEVICES" section:
To make the pairing of the devices added to the room devices section, first press the programming key of the
device and then press the button located under the room devices section. And save the changes.
7.3.2 Edit Room And Devices
Click on the desired room to edit the current room and press the button on Figure 11 Screen similar to
add room screen opens. The same processes as the add room screen are done. Examples of room editing
screens are given in the following figures.
PAIRING
ADD TO SCENARIO
(FAVORITE)
CHANGE ICON
SETTING TIME
DELETE DEVICE
Figure 13:Add Room Devices

18
Figure 14:Edit Room Screen
Enter icon change menü (Figure 7.28) to select appropriate icon to devices functions. First of all select the
device , and then press the button located under the room devices section. Icons appears, selecting the
appropriate icons for the devices. Figure 7.29 shows the icon change screen of 4-Button Relay Control devices.
Figure 15:Change Icon
Change Icon

19
To set the time, press the hourglass button under the Room Devices section. The duration of the devices is
entered and saved.
Figure 16: Setting Time
The devices to be added to the scenario are added to favorites from the star icon under the Room devices
section.
7.3.3 Edit Alarm
Press the “PROTECTION” button on the "Room Settings” screen. The opened screen will be as follows. The Zone
1, 2, 3, 4 section in this section shows the devices to which the alarm will be active. Example; Choose a lamp
from the device types. This lamp is connected to the alarm; the lamp will remain burned as long as the alarm
active. The lamp will turn off when the alarm occurs. The device can be activated by selecting the desired zone.
Setting Time
Favorite Settings

20
7.3.4 Smart Home Rf System
Back to the main menu after the settings have been done. When you enter the smart home page from
the main menu, the screen will be as follows:
7.4 Smart Home Knx System
Enter smart home application simply by tapping “SMART HOME” icon on the home screen.
If the smart home feature is not supported by your monitor, “NOT SUPPORTED” pop-up will appear. Smart home
devices have a special hardware, if you get this notice please check with your monitor provider, you might not
have a smart monitor.