Munters Rotem Communicator Instruction manual

Manual for use and maintenance
Communicator
Communication System
Ag/MIS/UmGB-2567-04/18 Rev 1.0
P/N: 116048
Communicator

© Munters AB, 2018 2
Communicator
Manual for use and maintenance
Revision: N.1.0 of 03.2019
Ag/MIS/UmGB-2567-04/18 Rev 4.5 (MIS)
Product Software: Version 3.07
This manual for use and maintenance is an integral part of the apparatus together with the attached
technical documentation.
This document is destined for the user of the apparatus: it may not be reproduced in whole or in part,
committed to computer memory as a file or delivered to third parties without the prior authorization of the
assembler of the system.
Munters reserves the right to effect modifications to the apparatus in accordance with technical and legal
developments.

© Munters AB, 2018 3
Index
Chapter page
1INTRODUCTION---------------------------------------------------------------------------------------- 6
1.1 Disclaimer ------------------------------------------------------------------------------------------ 6
1.2 Introduction ---------------------------------------------------------------------------------------- 6
1.3 Notes ----------------------------------------------------------------------------------------------- 6
2BEFORE USING ----------------------------------------------------------------------------------------- 7
3INTRODUCTION TO THE COMMUNICATOR ---------------------------------------------------- 8
3.1 Main features -------------------------------------------------------------------------------------- 8
3.2 Choosing communication cards------------------------------------------------------------------ 8
3.3 User interface -------------------------------------------------------------------------------------- 8
3.3.1 Front panel ....................................................................................................... 9
3.3.2 Menu tree......................................................................................................... 9
4INSTALLATION ---------------------------------------------------------------------------------------- 11
4.1 Hardware Installation --------------------------------------------------------------------------- 11
4.1.1 Preliminary Steps............................................................................................. 11
4.1.2 Connecting the unit to external components..................................................... 13
4.1.3 USB Driver Installation..................................................................................... 14
4.2 Connecting the Communicator to a Controller ----------------------------------------------- 14
4.2.1 Routing Methods............................................................................................. 14
4.2.2 RS-232 Connections ....................................................................................... 15
4.2.3 RS-485 Connection......................................................................................... 16
4.2.4Approximate Distances and Baud Rate............................................................ 17
4.3 Completing the Installation --------------------------------------------------------------------- 18
4.3.1 Configuring the communication to outside devices ........................................... 18
4.3.2 Communicator / Comm-Box Connectivity ........................................................ 18
5INITIAL CONFIGURATION------------------------------------------------------------------------- 20
5.1 Communication recommendations------------------------------------------------------------- 20
5.2 Setting the test schedule ------------------------------------------------------------------------ 21
5.3 Setting the language ---------------------------------------------------------------------------- 21
5.4 Setting the farm site name ---------------------------------------------------------------------- 21
5.5 Identifying the controllers ----------------------------------------------------------------------- 22
5.6 Setting the time & date-------------------------------------------------------------------------- 22
5.7 Adding names to the Address Book ----------------------------------------------------------- 22
5.7.1 Phone number structure ................................................................................... 23
5.8 Setting the password---------------------------------------------------------------------------- 23

© Munters AB, 2018 4
6COMMUNICATOR TO USER FUNCTIONS------------------------------------------------------ 24
6.1 Voice functions----------------------------------------------------------------------------------- 24
6.1.1 Basic voice functions ....................................................................................... 24
6.1.2 Advanced voice functions................................................................................ 25
6.1.3 Responding to an audio alarm message .......................................................... 27
6.2 Pager functions ---------------------------------------------------------------------------------- 28
6.2.1 Basic pager functions ...................................................................................... 28
6.2.2 Advanced pager functions .............................................................................. 29
6.3 Text functions ------------------------------------------------------------------------------------ 29
6.3.1 Basic text functions.......................................................................................... 29
6.3.2 Advanced text functions .................................................................................. 31
6.3.3 Text message responses.................................................................................. 31
6.4 Common Functions ------------------------------------------------------------------------------ 32
6.4.1 Test................................................................................................................. 33
6.4.2 Message Options ........................................................................................... 33
6.4.3 Hyper terminal ................................................................................................ 33
6.4.4 Monitor .......................................................................................................... 33
7COMMUNICATOR TO CONTROLLER FUNCTIONS ------------------------------------------- 34
7.1 Network connection configuration------------------------------------------------------------- 34
7.1.1 Configuring the channel settings ...................................................................... 34
7.1.2 Displaying the controllers ................................................................................ 35
7.1.3 Listing the network devices .............................................................................. 35
7.2 Channel/Signal tests ---------------------------------------------------------------------------- 35
7.2.1 Testing the RS-232/485 channel..................................................................... 36
7.2.2 Testing the Radio RF signal .............................................................................. 36
8COMMUNICATOR TO PC CONFIGURATION ------------------------------------------------- 37
8.1 Defining the communication speed with the local PC ---------------------------------------- 37
8.2 Configuring the data connection--------------------------------------------------------------- 37
9CONFIGURING THE DRY CONTACT CARD----------------------------------------------------- 38
10 COMMUNICATOR FUNCTIONS------------------------------------------------------------------ 39
10.1 Saving and restoring system settings----------------------------------------------------------- 39
10.2 Test functions------------------------------------------------------------------------------------- 39
10.2.1 Testing the backup battery ............................................................................. 39
10.2.2 Viewing device status...................................................................................... 40
10.2.3 Viewing the software and hardware version .................................................... 40
10.3 Viewing relay settings --------------------------------------------------------------------------- 40
11 ALARMS ------------------------------------------------------------------------------------------------ 41
11.1 Introduction to alarms and responses---------------------------------------------------------- 41
11.2 Event codes -------------------------------------------------------------------------------------- 42
11.3 Advanced alarm settings------------------------------------------------------------------------ 42

© Munters AB, 2018 5
11.3.1 Resetting the alarms ........................................................................................ 42
11.3.2 Disabling alarms ............................................................................................. 43
11.3.3 Defining the message delay ............................................................................ 43
11.3.4 Defining the message repeat parameter .......................................................... 43
11.3.5 Defining the internal alarms............................................................................. 44
11.3.6 Defining the battery alarm............................................................................... 44
11.4 Alarm and events history------------------------------------------------------------------------ 44
11.4.1 Displaying the alarm history ............................................................................ 44
11.4.2 Displaying the user events ............................................................................... 45
11.4.3 Displaying the system events ........................................................................... 45
11.5 Testing the alarm backup batteries ------------------------------------------------------------ 45
11.5.1 Dial-Up test ..................................................................................................... 46
11.5.2 Voltage test..................................................................................................... 46
12 TROUBLESHOOTING -------------------------------------------------------------------------------- 47
12.1 Hardware ---------------------------------------------------------------------------------------- 47
12.2 Communication to controllers/PC-------------------------------------------------------------- 47
12.3 Cellular modem---------------------------------------------------------------------------------- 49
12.4 RF communication ------------------------------------------------------------------------------- 50
12.5 Voice card --------------------------------------------------------------------------------------- 51
12.6 Alarm --------------------------------------------------------------------------------------------- 52
12.7 Line modem -------------------------------------------------------------------------------------- 52
12.8 Battery-------------------------------------------------------------------------------------------- 52
13 TECHNICAL DATA ------------------------------------------------------------------------------------ 53
14 APPENDIX A: REPLACING COMMUNICATION CARDS AND MODEMS ----------------- 54
14.1 Replacing the RS-232 card--------------------------------------------------------------------- 54
14.2 Replacing the RF-card --------------------------------------------------------------------------- 55
14.3 Installing a GSM-S or GSM-W card----------------------------------------------------------- 56
14.4 Installing a 3G Cell Modem Card ------------------------------------------------------------- 56
15 APPENDIX B: COMMUNICATOR / CONTROLLER CONNECTIVITY ------------------------ 58
16 APPENDIX C: ETHERNET CARD/ROTEMNET SETUP ------------------------------------------- 59
16.1 Setting Up an Internet connection-------------------------------------------------------------- 59
16.2 Setting Up a Network using RotemNet-------------------------------------------------------- 60
16.2.1 Local network.................................................................................................. 60
16.2.2 Remote network .............................................................................................. 61
17 WARRANTY-------------------------------------------------------------------------------------------- 62

© Munters AB, 2018 6
1Introduction
1.1 Disclaimer
Munters reserves the right to make alterations to specifications, quantities, dimensions etc. for production
or other reasons, subsequent to publication. The information contained herein has been prepared by
qualified experts within Munters. While we believe the information is accurate and complete, we make no
warranty or representation for any particular purposes. The information is offered in good faith and with
the understanding that any use of the units or accessories in breach of the directions and warnings in this
document is at the sole discretion and risk of the user.
1.2 Introduction
Congratulations on your excellent choice of purchasing a Communicator!
In order to realize the full benefit from this product it is important that it is installed, commissioned and
operated correctly. Before installation or using the fan, this manual should be studied carefully. It is also
recommended that it is kept safely for future reference. The manual is intended as a reference for
installation, commissioning and day-to-day operation of the Munters Controllers.
1.3 Notes
Date of release: May 2005
Munters cannot guarantee to inform users about the changes or to distribute new manuals to them.
All rights reserved. No part of this manual may be reproduced in any manner whatsoever without the
expressed written permission of Munters. The contents of this manual are subject to change without notice.

© Munters AB, 2018 7
2Before using
The Communicator is the central communication center and provides critical alarm warnings.
THEREFORE IT IS CRITICAL THAT YOU CARRY OUT THE FOLLOWING MAINTENANCE CHECKS
ACCORDING TO THE RECOMMENDED SCHEDULE:
1. Daily (minimum weekly) alarm tests. Refer to Setting the test schedule, page 20.
2. Monthly battery (minimum between flock) test.
oDisconnect power to Communicator
oEnsure Communicator transmits SMS and voice alarms.
oWait one hour, and confirm that Communicator continues to transmit alarms.
oRestore power to Communicator.
3. Test the Alarm Backup Batteries monthly (refer to page 45).
WARNING! Communicator does not support pre-paid SIM cards. Use a regular card only!
CAUTION Use an exclusive phone line for the Communicator!
NOTE: Sometimes using a phone line via private switchboard might interfere with communication.
Munters recommends using a different line to the Communicator.
CAUTION As a backup to the Communicator, Munters recommends installing an Emergency Light and
Siren system. If the Communicator is unable to transmit alarms via SMS or the telephone (for
example there is a complete power failure), the Emergency Light and Siren system sounds
an alarm.

© Munters AB, 2018 8
3Introduction to the Communicator
Munters Communicator, Version 3.06 is a state-of-the-art alarm and communication center used by famers
to monitor and control their Munters Controllers and accessories. The Communicator has a user friendly
interface with an alpha-numeric keypad, 20 character by 4 line LCD and indicative LED.
•Choosing communication cards
•Main features
•User interface
3.1 Main features
•Supports connectivity of several contacts simultaneously on various communication devices
(such as dial-up, internet, GSM, USB)
•Voice Solution Plug-in: Supports incoming and outgoing phone calls for alarms and status
reports. Voice messages can be edited according to personal preference.
•Remote access via dial-up connection
•Send and receive functional text messages (GSM/3G networks)
•Pager support
•3 dry contact, output relays 5 Amp
•8 digital inputs
•Battery backup
3.2 Choosing communication cards
The Communicator supports the following cards:
•Line modem: Supplies remote communication and voice alarms via a phone line.
•GSM-S/GSM-W: Supplies text alarms and text messages only.
•3G Cell Modem: Supplies text alarms and text messages only.
NOTE: GSM cards do not support voice, but if equipped with a SIM card, they can support the Voice
Dial-In function (Configuring the telephone modem, page 26).
NOTE: Use the GSM functions to set up a 3G Cell modem.
The Communicator has positions for two cards. Before ordering a unit, the user along with a dealer must
define which cards meet his needs and are supported by local infrastructure.
3.3 User interface
The following sections detail how to access and use the Communicator user interface.
•Front panel, page 9
•Menu tree, page 9

© Munters AB, 2018 9
3.3.1 FRONT PANEL
LED
Function
PC Com 1 TD/RD PC is transmitting/receiving data to/from the Communicator
Modem Com 2 TD/RD Modem is transmitting and receiving data
Modem Com 2 DTR/DCD Data transmitter ready/Data carrier detect (technician only)
Cellular Com 3 TD/RD Cellular modem is transmitting and receiving data
Controller Transmit Data Receive
Data
Controller relays are transmitting and receiving data
Output 1 Output 2 Non-functional
3.3.2 MENU TREE
Table 1: Menus
My Farm
Alarm
History
System
Farm Name Reset Alarm Test
Address Book Test Schedule User Events Digital Input
Status Report Disabled Alarms System Events Relay
Controllers Options Save / Resetting
Password Language

© Munters AB, 2018 10
My Farm
Alarm
History
System
Time & Date Advanced Setup
Technician Tools
Table 2: Sub Menus
Test
Save/Resetting
Advanced Setup
Battery Signal Strength Restore Voice
GSM Send Text MSG Save RF/Wired Network
Radio RF Signal Dial Out Battery
Hardware Profile Internet
Wired RS232/485 COM/USB
Network List Line Modem
Voice GSM
Pager Pager
Dial Out
NOTE: Use the GSM functions to set up a 3G Cell modem.