My Clean Buddy Jr. User manual

Household disinfectant
generator
Disinfects
Cleans
Sanitizes
Deodorizes
My Clean Buddy Jr.
Product Manual

Whats Included
1 x My Clean Buddy Jr.
1 x usb charging cord
1 x scooper
Product Parameters
Product Overview
My Clean Buddy Jr can produce 500mg/l of disinfectant which can quickly and
effectively kill: E. Coli, Staphylococcus aureus, Candida albicans, and many more
germs and bacteria! It’s safe, environmentally friendly, And a great alternative
disinfectant.
Maintenance
How to use
Instructions for use
1. Do not place bottle close to any heat sources.
2. Do not place the My Clean Buddy into water.
3. After solution is created unplug the power cord from the device
4. Although bleaching is an uncommon occurrence, we still do not recommend
use on leather or silk goods.
Spray and let soak for 10 seconds and then wipe clean with rag or paper towel.
1) Fill the My Clean Buddy Jr with distilled water with 400ml of water
(approximately 3/4 full).
Sanitizing mode (recommended for use with the My Clean Buddy)

Salt
2) Add 1 table spoon of table salt (approximately 15-20g of salt).
3) Power on the My Clean Buddy Jr; But do not attach the spray attachment, and a
series of flashing lights will begin and will end on blue. (Signifying the start of the
solution making process.).
4) After 5 minutes a beep will signify the end of the process.
5) At this point you can pour the solution into your My Clean Buddy for a powerful
disinfecting mist or you can spray directly from the My Clean Buddy Jr with the
spray attachment.
6) Once finished with use; you can empty the solution maker and flush with water,
or store the solution created. (We recommend no longer than 1 week of storage
time.

Salt
1) Fill the My Clean Buddy Jr with distilled water with 400ml of water
(approximately 3/4 full).
2) Add 1 table spoon of table salt (approximately 15-20g of salt).
3) Power on the My Clean Buddy Jr; But do not attach
the spray attachment, and a series of flashing lights will
begin. Press the power button again and the light will
end on purple. (Signifying the start of the solution
making process).
4) After 10 minutes a beep will signify the end of the
process.
Degreaser mode (recommended for use directly with the My Clean
Buddy Jr.)

5) At this point you can attach the spray attachment and begin spraying surfaces.
(Remember to wipe after use).
6) Once finished with use; you can empty the solution maker and flush with water,
or store the solution created. (We recommend no longer than 1 week of storage
time.
Pressure is generated during the preparation of the solution making process. DO
NOT tighten the spray attachment to the bottle wile the solution process is active.
The force generated will be high and may damage the unit.
When using for the first time after a prolonged storage time, clean thoroughly
before use.
This product is for both home and commercial use. Failure to follow the
instructions may cause a failure in the device and my lead to a voided warranty.
To prevent electrical issues and avoid to dangerous instances, do not submerse
the My Clean Buddy Jr and its power cord into water.
DO NOT insert or remove plug with wet hands.
If the power cord is damaged it must be replaced.
Please read the manual thoroughly before use.
Blue Light (Sanitize) Production takes 5 minutes
Purple Light (Degreaser) Production takes 10 minutes
Red Light - Charging
Green Light - Full charge
Tips
Lighting Tips
Precautions

Username Purchase Date
Local dealer stamp
User Address
Product name or model
Product ID
Username Purchase Date
User Address
Product name or model Product ID
Repair Centre:
Address:
Phone:
Note: 1. Please keep this card properly. When maintenance is needed, contact this
company's special maintenance center with this card and bill.
2. If the address and telephone are changed, please notify the authorized repair
center.
Warranty Card
Please crop along this dotted line
Product warranty card registration card (return receipt)