Naomi Home Brisbane Glider and Ottoman User manual

Assembly Instructions
Product Dimensions:
24.75” D x 25.75” W x 39.5” H
Please take a moment to read through the entire instruction booklet before assembly to
familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
If you need help or have damaged or missing parts, contact customer service at
www.NaomiHome.com.
Page 1 of 8
NAOMI
Brisbane Glider and Ottoman
HOME
©
2020 Naomi Home, Inc. - All Rights Reserved.
FRONT

Tools Required
Phillips Screwdriver
(Medium)
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD
•This product includes small parts, sharp points and sharp edges in its unassembled
state. Keep unassembled parts away from children under 3 years of age, & animals.
•If used improperly, your doll bunk bed may be pulled over or fall, creating risk of injury or
damage. Children should not be permitted to climb or pull on the glider or ottoman.
USE AND MAINTENANCE
•Use on level surfaces only
•Because this product needs assembly, it is prone to working itself loose from time to
time depending on the use. Please take the time to check that all connections are still
tight and working properly for safety.
•Only clean using a damp cloth and mild detergent, do not use bleach or abrasive
cleaners.
PARENTAL SUPERVISION IS REQUIRED
•This Naomi Home product is intended for adult use.
•Parents or Guardians should supervise use under the intended age specifically
regarding children that may have access to it and might climb on the unit.
ASSEMBLY RECOMMENDATIONS
•Check you have all the components and tools listed on page 2 and 3.
•Do not stand or put weight on this product during assembly, this could cause damage.
•Remove all hardware from the plastic bags and separate them into their groups.
•Assemble the item as close to its final position (in the same room) as possible.
•Assemble on a soft level surface to avoid damaging the unit or your floor.
•Make sure you have enough space to layout the parts before starting.
•Parts of the assembly may be easier with 2 people.
•Dispose of all packaging carefully and responsibly.
•Do not use this item if any components are missing or damaged.
•We do not recommend the use of power drill/drivers for inserting screws, as this could
damage the unit. Only use hand screwdrivers.
WARNING CAUTION
Allen Wrench
(included)
Page 2 of 8

This drawing is to give you an overall idea only of how this assembly will go together and does
not replace the assembly instructions.
Please take a moment to read through the whole instruction booklet before assembly to familiarize
yourself with this product. Once you feel ready to start, follow the instructions step by step and this should
make this process as easy as we could make it for you.
Due to the number of parts involved
assembly can take a few minutes
so set aside between 20 and
30 minutes to assemble this
without rushing.
ASSEMBLY AT A GLANCE
Page 3 of 8
LEFT FRAME
Left
LEFT ARM
2
1
Right
2
4
6
6
3
7
FRONT
5

Page 4 of 8
Left/Right Arm Cushions (x2)
OTTOMAN
7
Ottoman (x1)
GLIDER COMPONENT PARTS
ASSEMBLY HARDWARE
1
Back Rest (x1)
5
Back Cushion (x1)
4 6
Seat Cushion (x1)
35mm Allen Head Bolts (x6)
A
D
Allen Key (x1)
50mm Allen Head Bolts (x2)
B
C
Barrel Nuts (x2)
3
Glider Base assembly (x1)
2
Left/Right Arms (x2)
Left
Right
LEFT ARM

GLIDER ASSEMBLY INSTRUCTIONS
2
1
Select 1 Backrest, 3
Glider Base Assembly,
A bolt (x2), D wrench.
On the back of the
seat support, align the
backrest to the seat
support and make
sure the curve ends of
backrest match the
seat support. Insert 2
A bolts and tighten
with D wrench.
Page 5 of 8
Select 2 - Left Arm, 2 - Right
Arm, A bolt (x4), B long bolt
(x2), C barrel nut (x2). Place
2-Left Arm (seated left) on seat
support and align armrest hole
with backrest hole. Insert C
barrel nut in armrest underside
hole and align with screw-
driver. Insert B long bolt
through hole in backrest, into
armrest and into barrel nut.
Finger tighten. Insert 2 A bolts
in arm cross bar holes and
tighten with D wrench. Tighten
B bolt with D wrench. Repeat
for 2 - Right Arm.
3
1
FRONT
BACK
Sticker
LEFT ARM
FRONT
Sticker
LEFT ARM
Sticker
RIGHT ARM
B
1
3
2
2
2
1
B
B
1
3
A
A
A
C
C
C
A
A

GLIDER ASSEMBLY INSTRUCTIONS
4
3
Select 6 arm cush-
ion (x2). Note
pockets on 7 cush-
ions. Start with
end of 7 without
pocket. Snap top
of cushion to
armrest snaps.
Wrap cushion
around armrest
and snap bottom
pocket by base of
armrest snaps.
Repeat for other 7
cushion.
Select 5 seat
cushion. Place 5
seat cushion into
Glider assembly
with fabric straps
side down. Tie
seat cushion
fabric straps on
backrest spindle.
Repeat for other
fabric strap.
Page 6 of 8
BACK
RIGHT ARM
FRONT
6
2
2
6
1
1
6
6
5
5

GLIDER ASSEMBLY INSTRUCTIONS
6
5
Select 4 Backrest
Cushion. Insert 4
Backrest Cushion
into assembly
with straps
toward 1 back-
rest. Tie straps to
spindles on 1.
Glider Complete. Place
completed glider into
position. Place 7 otto-
man in front of glider.
Page 7 of 8
BACK
4
1
1
4

ASSEMBLY COMPLETE
Page 8 of 8
www.NaomiHome.com
MADE IN VIETNAM
Product Packaging Information
Model #:
Color:
Shipment Ref. #:
Date:
________________________________
__________________________________
_________________________
__________________________________
CONGRATULATIONS, YOUR NAOMI HOME BRISBANE
GLIDER AND OTTOMAN SET IS COMPLETE!
NAOMI
HOME