National Instruments NI EVS-1463 User manual

Getting Started with the NI EVS-1463
The NI EVS-1463 is a fanless embedded vision system designed for rugged industrial applications.
The NI EVS-1463 features a Windows operating system and a variety of industrial communication
connectors. The NI EVS-1463 supports Base configuration Camera Link-compatible cameras, GigE
Vision cameras, and DirectShow-compatible USB cameras. The NI EVS-1463 features a 15-pin D-SUB
connector that has four external TTL I/O lines, two optically isolated inputs, and two RS-422 inputs.
This document describes how to install the NI EVS-1463 hardware and acquire an initial image.
Refer to the NI EVS-1463 Series User Manual for device and I/O specifications, mounting requirements,
and answers to common questions about network, firewall, hardware, software, and power issues. To
access the NI EVS-1463 Series User Manual, select Start»All Programs»National Instruments»
Vision»Documentation»NI-IMAQ.
What You Need to Get Started
The following components are included in the NI EVS-1463 kit:
❑NI EVS-1463
❑DVI splitter cable
❑Three-position power connector
❑NI Vision Acquisition Software DVD
Required Hardware
In addition to the items included in the NI EVS-1463 kit, the following components are necessary to
set up and configure the NI EVS-1463.
❑One of the following power supply options:
Caution Use the NI EVS-1463 only with a 24 VDC, UL listed, limited power source (LPS) supply.
The power supply will bear the UL listed mark, LPS. The power supply must also meet any safety
and compliance requirements for the country of use.
– PS-5 Power Supply, 24 VDC, 5 A, Universal Power Input (part number 778805-90)
– Any 24 VDC ±10%, 70 W or greater power supply
❑One of the following types of cameras:
– Base configuration Camera Link-compatible camera
– GigE Vision camera
– DirectShow-compatible USB camera

Getting Started with the NI EVS-1463 2 ni.com
❑One of the following cables corresponding to your camera type:
– MDR 26-pin Camera Link cable for connecting to Base configuration Camera
Link-compatible camera
– CAT 5e or CAT 6 1000Base-T Ethernet cable for connecting to GigE Vision cameras
– USB cable for connecting to DirectShow-compatible USB cameras
Safety Information
The following section contains important safety information that you must follow when installing and
using the hardware.
Do not operate the hardware in a manner not specified in this document and in the user documentation.
Misuse of the hardware can result in a hazard. You can compromise the safety protection if the hardware
is damaged in any way. If the hardware is damaged, return it to National Instruments for repair.
Clean the hardware with a soft, nonmetallic brush. Make sure that the hardware is completely dry and
free from contaminants before returning it to service.
Do not substitute parts or modify the hardware except as described in this document. Use the hardware
only with the chassis, modules, accessories, and cables specified in the installation instructions or
specifications. You must have all covers and filler panels installed during operation of the hardware.
Do not operate the hardware in an explosive atmosphere or where there may be flammable gases or
fumes unless the hardware is UL (U.S.) or Ex (EU) Certified and marked for hazardous locations.
The hardware must be in a suitably rated IP 54 minimum enclosure for hazardous locations. Refer to
the hardware’s user documentation for more information.
You must insulate signal connections for the maximum voltage for which the hardware is rated. Do not
exceed the maximum ratings for the hardware. Do not install wiring while the hardware is live with
electrical signals. Do not remove or add connector blocks when power is connected to the system. Avoid
contact between your body and the connector block signal when hot swapping hardware. Remove power
from signal lines before connecting them to or disconnecting them from the hardware.
Operate the hardware only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid,
or gaseous state that can reduce dielectric strength or surface resistivity. The following is a description
of pollution degrees:
• Pollution Degree 1 means no pollution or only dry, nonconductive pollution occurs. The pollution
has no influence. Typical level for sealed components or coated PCBs.
• Pollution Degree 2 means that only nonconductive pollution occurs in most cases. Occasionally,
however, a temporary conductivity caused by condensation must be expected. Typical level for
most products.
• Pollution Degree 3 means that conductive pollution occurs, or dry, nonconductive pollution occurs
that becomes conductive due to condensation.
Operate the hardware at or below the measurement category1marked on the hardware label.
Measurement circuits are subjected to working voltages2and transient stresses (overvoltage) from the
circuit to which they are connected during measurement or test. Measurement categories establish
1 Measurement categories, also referred to as overvoltage or installation categories, are defined in electrical safety standard
IEC 61010-1 and IEC 60664-1.
2 Working voltage is the highest rms value of an AC or DC voltage that can occur across any particular insulation.

©National Instruments Corporation 3 Getting Started with the NI EVS-1463
standard impulse withstand voltage levels that commonly occur in electrical distribution systems. The
following is a description of measurement categories:
• Measurement Category I is for measurements performed on circuits not directly connected to the
electrical distribution system referred to as MAINS1voltage. This category is for measurements of
voltages from specially protected secondary circuits. Such voltage measurements include signal
levels, special hardware, limited-energy parts of hardware, circuits powered by regulated
low-voltage sources, and electronics.
• Measurement Category II is for measurements performed on circuits directly connected to the
electrical distribution system (MAINS3). This category refers to local-level electrical distribution,
such as that provided by a standard wall outlet (for example, 115 AC voltage for U.S. or 230 AC
voltage for Europe). Examples of Measurement Category II are measurements performed on
household appliances, portable tools, and similar hardware.
• Measurement Category III is for measurements performed in the building installation at the
distribution level. This category refers to measurements on hard-wired hardware such as hardware
in fixed installations, distribution boards, and circuit breakers. Other examples are wiring,
including cables, bus bars, junction boxes, switches, socket outlets in the fixed installation, and
stationary motors with permanent connections to fixed installations.
• Measurement Category IV is for measurements performed at the primary electrical supply
installation typically outside buildings. Examples include electricity meters and measurements on
primary overcurrent protection devices and on ripple control units.
To obtain the safety certification(s) for this product, visit ni.com/certification, search by model
number or product line, and click the appropriate link in the Certification column.
Electromagnetic Compatibility Information
This hardware has been tested and found to comply with the applicable regulatory requirements
and limits for electromagnetic compatibility (EMC) as indicated in the hardware’s Declaration of
Conformity (DoC)2. These requirements and limits are designed to provide reasonable protection
against harmful interference when the hardware is operated in the intended electromagnetic
environment. In special cases, for example when either highly sensitive or noisy hardware is being used
in close proximity, additional mitigation measures may have to be employed to minimize the potential
for electromagnetic interference.
While this hardware is compliant with the applicable regulatory EMC requirements, there is no
guarantee that interference will not occur in a particular installation. To minimize the potential for
the hardware to cause interference to radio and television reception or to experience unacceptable
performance degradation, install and use this hardware in strict accordance with the instructions in
the hardware documentation and the DoC1.
1 MAINS is defined as a hazardous live electrical supply system that powers hardware. Suitably rated measuring circuits may
be connected to the MAINS for measuring purposes.
2 The Declaration of Conformity (DoC) contains important EMC compliance information and instructions for the user or
installer. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line,
and click the appropriate link in the Certification column.

Getting Started with the NI EVS-1463 4 ni.com
If this hardware does cause interference with licensed radio communications services or other nearby
electronics, which can be determined by turning the hardware off and on, you are encouraged to try to
correct the interference by one or more of the following measures:
• Reorient the antenna of the receiver (the device suffering interference).
• Relocate the transmitter (the device generating interference) with respect to the receiver.
• Plug the transmitter into a different outlet so that the transmitter and the receiver are on different
branch circuits.
Some hardware may require the use of a metal, shielded enclosure (windowless version) to meet the
EMC requirements for special EMC environments such as, for marine use or in heavy industrial areas.
Refer to the hardware’s user documentation and the DoC1for product installation requirements.
When the hardware is connected to a test object or to test leads, the system may become more sensitive
to disturbances or may cause interference in the local electromagnetic environment.
Operation of this hardware in a residential area is likely to cause harmful interference. Users are required
to correct the interference at their own expense or cease operation of the hardware.
Changes or modifications not expressly approved by National Instruments could void the user’s right to
operate the hardware under the local regulatory rules.
Thermal Considerations and Mounting
To maximize the cooling efficiency of the NI EVS-1463, observe the following recommendations:
• Mount the NI EVS-1463 on a thermally conductive surface.
• Avoid static air environments.
• Mount the NI EVS-1463 with the heatsink facing upward. If you mount the NI EVS-1463 on a wall
or other vertical surface, mount the device so that the heat sink fins are vertical.
Note The NI EVS-1463 Camera Link hardware is equipped with a temperature monitor. The
Camera Link hardware will stop acquiring images if it reaches its maximum allowable temperature.
An error will occur, reporting that the maximum temperature has been reached.
Refer to the NI EVS-1463 Series User Manual for dimensional drawings, additional mounting
information, and detailed device specifications.
Unpacking and Verifying Components
Remove the NI EVS-1463 from the package and inspect the device for any sign of damage. Notify
National Instruments if the device appears damaged in any way. Do not use a damaged device.
Installing Hardware
Ensure that the AC input to the external power supply is disconnected before plugging in or unplugging
any connector. Ground the unit to minimize the possibility of static electricity damage.

©National Instruments Corporation 5 Getting Started with the NI EVS-1463
Refer to Figure 1 while completing the following steps to install the NI EVS-1463.
Figure 1. NI EVS-1463 Connectors
1. Connect a USB keyboard and USB mouse to any available USB connector.
2. Connect a DVI monitor to the DVI connector, or use the DVI splitter cable (supplied) to connect a
VGA monitor or dual monitors. For independent displays in dual monitor mode, one monitor must
support a DVI-D interface and the other must support a VGA analog interface.
Note Connect all monitors before you supply power to the NI EVS-1463.
3. If you want to connect the NI EVS-1463 to a network, use an Ethernet cable to connect the Ethernet
hub to the primary network connector on the NI EVS-1463.
Caution To prevent data loss and to maintain the integrity of your Ethernet installation, do not use
a cable longer than 100 m. If you are using a 1,000 Mbps Ethernet, use a CAT 5e or CAT 6 shielded
twisted-pair Ethernet cable. Use a shielded twisted pair Ethernet cable for maximum signal integrity.
4. Connect devices to other connectors as required by your system configuration.
1 Primary Network Connector
2 Secondary Network Connector
3 Reset Switch
4 Audio In Connector
5 Audio Out Connector
6 Safe Mode/IP Reset/No App/
User 1/CF Master/Slave Switches
7 User 2/User 1/HDD/Power LEDs
8 CompactFlash Slot
9 Power Supply Connector
10 Grounding Lug
11 DVI-I Connector
12 MDR 26-Pin Connector
13 RS-232 Serial Connector (COM1)
14 MXI Express x1 Connector
15 15-Pin D-SUB I/O Connector
16 USB Connectors
RESET
MXIex1
COMPACT FLASH
INPUT
10-20V
90W MAX
USER 2
USER 1
HDD
POWER
CF MS/SL
SAFE MODE
IP RESET
NO APP
USER 1
12378
911
14 1316
65
15 12 10
TRIGGERS
CAMERA LINK
!
4

Getting Started with the NI EVS-1463 6 ni.com
Connecting a Camera
To connect a camera to the NI EVS-1463, complete the following steps:
1. Connect the appropriate cable to your camera. Refer to your camera manufacturer documentation
for specific instructions about how to connect the cable to your camera.
2. Complete the following step for your camera type to connect the camera to the NI EVS-1463:
•Base Configuration Camera Link Compatible Cameras—Connect the camera MDR
26-pin Camera Link cable to the MDR 26-pin connector on the NI EVS-1463 front panel.
•GigE Vision Cameras—Connect the camera Ethernet cable to the secondary network
connector on the NI EVS-1463 front panel.
•DirectShow-Compatible USB Cameras—Connect the camera USB cable to a USB
connector on the NI EVS-1463 front panel.
The camera is now attached to the NI EVS-1463.
Connecting the Power Supply
To connect a power supply to the NI EVS-1463, complete the following steps.
1. Connect the power supply to the 3-position power connector.
2. Connect the 3-position power connector to the power supply connector on the NI EVS-1463.
3. Plug the power supply cord into an outlet.
The power LED will illuminate and the NI EVS-1463 will boot when the power supply is properly
connected.
Interfacing with Camera Link Cameras
To interface with a Camera Link camera connected to the NI EVS-1463, you must associate the camera
with the appropriate camera file. Complete the following steps to use Measurement and Automation
Explorer (MAX) to associate a camera file with your Camera Link camera:
1. Select Start»All Programs»National Instruments»Measurement & Automation to launch
MAX.
2. Expand the Devices and Interfaces branch of the configuration tree.
3. Expand the NI-IMAQ Devices branch.
4. Expand the NI PCIe-1427 branch.
5. Right-click Channel 0 and select Camera.
6. Select your camera from the menu. If your camera is not in the menu, verify that the appropriate
camera file is installed in the <NI-IMAQ>\Data directory.
For more information about camera files, refer to the Camera Files section of Chapter 1, NI EVS-1463
Series Overview, in the NI EVS-1463 Series User Manual.

©National Instruments Corporation 7 Getting Started with the NI EVS-1463
Acquiring an Image with MAX
Complete the following steps to acquire an image using MAX:
1. Select Start»All Programs»National Instruments»Measurement & Automation to launch
MAX.
2. Expand the Devices and Interfaces branch of the configuration tree.
3. Complete the following step for your camera type to select the camera:
•Base Configuration Camera Link Compatible Cameras—Expand the NI-IMAQ Devices
branch, then expand the NI PCIe-1427 branch and select Channel 0.
•GigE Vision or DirectShow-Compatible USB Cameras—Expand the NI-IMAQdx
Devices branch and select a camera.
4. Click Snap to acquire a single image, or click Grab to acquire continuous images. Click Grab
again to stop a continuous acquisition.
The NI EVS-1463 is now configured and acquiring images. Use LabVIEW to create your application.
Refer to the Where to Go from Here section for a list of documentation and other resources to help you
set up and use the NI EVS-1463 in an application.
Acquiring an Image with Vision Builder AI
The NI EVS-1463 includes Vision Builder AI for evaluation purposes. Visit ni.com/vision to
purchase a license for Vision Builder AI.
Complete the following steps to acquire an image using Vision Builder AI:
1. On the Vision Builder AI Welcome screen, click Configure Inspection.
2. In the Inspection Steps palette, select the Acquire Images tab.
3. Click the image acquisition step for your camera type:
•Base Configuration Camera Link compatible cameras—Use the Acquire Image step.
•GigE Vision or DirectShow-Compatible USB Cameras—Use the Acquire Image
(1394, GigE, or USB) step.
The property page for the step opens.
4. Click Acquire Single Image to acquire an image from the NI EVS-1463.
5. Click OK to add the step to the inspection.
The device is now configured and acquiring images. Use Vision Builder AI to add and configure
additional inspection steps to create your application. Refer to the Where to Go from Here section for a
list of resources to help you set up and use the NI EVS-1463RT in an application.
Specifications
Refer to the NI EVS-1463 Series User Manual for detailed device and I/O specifications.
Environment
NI EVS-1463 systems are intended for indoor use only.
Maximum altitude..................................................2,000 m
Pollution Degree (IEC 60664) ...............................2

Getting Started with the NI EVS-1463 8 ni.com
Operating Environment
Ambient temperature range ...................................0 °C to 45 °C
(IEC 60068-2-1 and IEC 60068-2-2)
Relative humidity range (IEC 60068-2-56) ...........10% to 90% noncondensing
Caution Clean the NI EVS-1463 with a soft nonmetallic brush. Make sure that the system is
completely dry and free from contaminants before powering-on the controller again.
Storage Environment
Ambient temperature range ...................................–40 °C to 70 °C
(IEC 60068-2-1 and IEC 60068-2-2)
Relative humidity range (IEC 60068-2-56) ...........5% to 95% noncondensing
Shock and Vibration
Operational shock ..................................................30 g peak, half-sine, 11 ms pulse
(Tested in accordance with IEC-60068-2-27.
Test profile developed in accordance with
MIL-PRF-28800F.)
Random vibration
Operating .......................................................5 to 500 Hz, 0.3 grms (with solid-state hard drive)
Nonoperating .................................................5 to 500 Hz, 2.4 grms
(Tested in accordance with IEC-60068-2-64.
Nonoperating test profile exceeds the requirements
of MIL-PRF-28800F, Class 3.)
Safety
This product is designed to meet the requirements of the following standards of safety for electrical
equipment for measurement, control, and laboratory use:
• IEC 61010-1, EN-61010-1
• UL 61010-1, CSA 61010-1
Note For UL and other safety certifications, refer to product label or the Online Product
Certification section.
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for electrical equipment for
measurement, control, and laboratory use:
• EN 61326 (IEC 61326): Class A emissions; Basic immunity
• EN 55011 (CISPR 11): Group 1, Class A emissions
• AS/NZS CISPR 11: Group 1, Class A emissions
• FCC 47 CFR Part 15B: Class A emissions
• ICES-001: Class A emissions
Note Note For the standards applied to assess the EMC of this product, refer to product label or the
Online Product Certification section.
Note Note For EMC compliance, operate this product according to the documentation.

©National Instruments Corporation 9 Getting Started with the NI EVS-1463
CE Compliance
This product meets the essential requirements of applicable European Directives as follows:
• 2006/95/EC; Low-Voltage Directive (safety)
• 2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Online Product Certification
Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance
information. To obtain product certifications and the DoC for this product, visit ni.com/
certification, search by model number or product line, and click the appropriate link in the
Certification column.
Environmental Management
National Instruments is committed to designing and manufacturing products in an environmentally
responsible manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial not only to the environment but also to NI customers.
For additional environmental information, refer to the NI and the Environment Web page at ni.com/
environment. This page contains the environmental regulations and directives with which NI
complies, as well as other environmental information not included in this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products must be sent to a WEEE recycling
center. For more information about WEEE recycling centers, National Instruments WEEE initiatives,
and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, visit
ni.com/environment/weee.
Battery Replacement and Disposal
Battery Directive This device contains a long-life coin cell battery. If you need to replace it, use the
Return Material Authorization (RMA) process or contact an authorized National Instruments service
representative. For more information about compliance with the EU Battery Directive 2006/66/EC
about Batteries and Accumulators and Waste Batteries and Accumulators, visit ni.com/
environment/batterydirective.
Cd/Hg/Pb
⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS˅
Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ (RoHS)DŽ
݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/environment/rohs_chinaDŽ
(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

Getting Started with the NI EVS-1463 10 ni.com
Where to Go from Here
The following documents and resources contain information you may find helpful as you set up and use
the NI EVS-1463 in an application.
Refer to the NI EVS-1463 Series User Manual for detailed information about:
• Device and I/O specifications
• Mounting requirements
• Answers to common questions about network, firewall, hardware, software, and power issues
Additional Resources for Vision Builder for Automated Inspection Users
Refer to the NI Vision Builder for Automated Inspection Tutorial to learn how to perform basic machine
vision techniques using Vision Builder AI. You can access the NI Vision Builder for Automated
Inspection Tutorial and other documentation by selecting Start»All Programs»National
Instruments»Vision Builder AI»Documentation. You can also access context help within
Vision Builder AI by clicking the Show Context Help button on the Vision Builder AI toolbar.
Examples of common Vision Builder AI inspections are installed to the <Vision Builder AI>\
Examples directory.
Visit the NI Developer Zone at ni.com/zone for the latest example programs, tutorials, technical
presentations, and a community area where you can share ideas, questions, and source code with
developers around the world.
Additional Resources for LabVIEW Users
Documentation for LabVIEW is available from the Help menu on the LabVIEW toolbar. You can access
documentation for the NI Vision Development Module by selecting Start»All Programs»National
Instruments»Vision»Documentation»NI Vision.
Documentation for the NI-IMAQ driver software is available by selecting Start»All Programs»
National Instruments»Vision»Documentation»NI-IMAQ.
Documentation for the NI-IMAQdx driver software is available by selecting Start»All Programs»
National Instruments»Vision»Documentation»NI-IMAQdx.
Documentation for the MAX configuration software is available from the Help menu on the MAX
toolbar. Specific information about using MAX with NI Vision hardware is available by selecting
Help»Help Topics»NI Vision.
Examples of image acquisitions and common machine vision inspections are installed to the
<LabVIEW>\Examples\IMAQ and <LabVIEW>\Examples\Vision directories, where
<LabVIEW> is the location where LabVIEW is installed.
Visit the NI Developer Zone at ni.com/zone for the latest example programs, tutorials, technical
presentations, and a community area where you can share ideas, questions, and source code with
developers around the world.

©National Instruments Corporation 11 Getting Started with the NI EVS-1463
Where to Go for Support
The National Instruments Web site is your complete resource for technical support. At ni.com/
support you have access to everything from troubleshooting and application development self-help
resources to email and phone assistance from NI Application Engineers.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European
Communities using the manufacturer’s declaration of conformity. This system affords the user
protection for electronic compatibility (EMC) and product safety. You can obtain the DoC for your
product by visiting ni.com/certification. If your product supports calibration, you can obtain the
calibration certificate for your product at ni.com/calibration.
National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin,
Texas, 78759-3504. National Instruments also has offices located around the world to help address your
support needs. For telephone support in the United States, create your service request at ni.com/
support and follow the calling instructions or dial 512 795 8248. For telephone support outside the
United States, contact your local branch office:
Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020,
Brazil 55 11 3262 3599, Canada 800 433 3488, China 86 21 5050 9800,
Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, Finland 358 (0) 9 725 72511,
France 01 57 66 24 24, Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737,
Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28,
Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,
New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 328 90 10,
Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886,
Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085,
Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222,
Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.
Refer to the Terms of Use section on ni.com/legal for more information about National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade
names of their respective companies. For patents covering National Instruments products/technology,
refer to the appropriate location: Help»Patents in your software, the patents.txt file on your
media, or the National Instruments Patent Notice at ni.com/patents.
© 2009 National Instruments Corporation. All rights reserved. 375152A-01 Dec09