natus Bio-logic AuDX PRO User manual

Bio-logic®AuDX®PRO QUICK START GUIDE
Quick start

Bio-logic®AuDX®PRO QUICK START GUIDE
2
Note: this screen (test options) can vary depending on your set up
Turning On/Off and changing the device
Start menu
On/off button on
right side
Power supply
connector
Battery statusCurrent time
Customize settings
Turn off device
Select patient
View test result history for
selected patient
Additional information about
options for current screen

Bio-logic®AuDX®PRO QUICK START GUIDE
3
Testing: Distortion Product Otoacustic Emissions (DPOAE) Screening
Connect the probe to the red connector.
Select one of the Presets for DPOAE Screening
Select the appropriate ear tip size and place it on the probe tip.
Insert the probe in the ear making sure that the ear tip fits tightly into the ear canal.
Select the test ear by pressing either the Right or Left button.
Cartoon mode will start the test showing a cartoon instead of the progress bar.

Bio-logic®AuDX®PRO QUICK START GUIDE
4
A calibration will be performed prior to measurement.
A green light indicates successful calibration (below left).
After successful ear probe calibration, the test will start automatically.
Probe fit override for patients with
PE tubes or tympanic membrane
perforation
Progress for each test
frequency
Overall test
progress
Noise floor
level

Bio-logic®AuDX®PRO QUICK START GUIDE
5
Overall screening test
result
Green check marks indicate
valid response. Red circles
indicate no valid response
Red (right ear) or blue (left
ear) bars show response
amplitude. Grey bars show
noise amplitude
Retest frequencies that
did not pass
Print results to a label or
to a pdf file
Test other ear
Switch to results of the other ear after
both ears have been tested
Note: These circles indicate that other
screens are available to view. Swipe your
finger right or left to get other views.
DPOAE screening test results

Bio-logic®AuDX®PRO QUICK START GUIDE
6
Select the appropriate ear tip size and place it on the probe tip.
Insert the probe in the ear making sure that the ear tip fits tightly into the ear canal.
Select the test ear by pressing either the Right or Left button. Select Cartoon mode to start the test showing
a cartoon instead of the progress bar. This can be changed during the test by tapping on the plane
icon at the bottom of the device screen.
DPOAE diagnostic / high reolution
Connect the probe to the red connector.
Select one of the Presets for DPOAE Diagnostic.

Bio-logic®AuDX®PRO QUICK START GUIDE
7
A calibration will be performed prior to measurement. A green light indicates successful calibration. After successful ear probe
calibration, the test will start automatically. Please note that the presets for DPOAE diagnostics are HiRes, which allows testing
frequencies in 10 Hz increments or up to 30 points per octave.
Probe fit override for patients with PE
tubes or middle ear perforations
Noise
floor level
Overall test progress
Progress for each test
frequency
Skip a
frequency
Stop test
Resume test
Switch to
cartoon mode

Bio-logic®AuDX®PRO QUICK START GUIDE
8
Note: These circles indicate that
other screens are available to
view. Swipe your finger right or
left to get other views.
Green check marks
indicate valid response
Red or blue bars indicate
response, grey bars indicate
noise
Print results to a label
or to a pdf file
Outcome for each test
sorted by f2 and L2.
Multilevel test results shown.
Tap on screen to view details
for each level tested.
High resolution test results (4
PPO)
Test
other ear
Numeric values shown in table
format
DPOAE diagnostic test results

©2020 Natus Medical Incorporated. All Rights Reserved. All product names appearing on this document
are trademarks or registered trademarks owned, licensed to, promoted or distributed by Natus Medical
Incorporated, its subsidiaries or affiliates. 7-26-1385-EN Rev01
Healthcare solutions with one thing in mind. You.
natus.com
Natus Medical Incorporated
Bio-logic®AuDX®PRO QUICK START GUIDE
Quick Guide Information
Release date: 2017-01-11
Revision: 02
Valid from: Firmware Rev. 2.1, Bio-link PC Software Rev. 2.0
All mentioned items, products, brands and trademarks are registered or owned by the mentioned companies.
All information, illustrations, and specifications provided within this manual are based on the latest product information available
at the time of publication. PATH medical reserves the right to make changes at any time without notice.
Please contact your local Bio-logic distributor for further information.
Errors and omissions excepted.
Copyright Notice
No part of this manual may be reproduced, translated, stored, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written consent of PATH medical GmbH.
Copyright © 2016 PATH medical GmbH
Legal manufacturer of the Bio-logic devices:
PATH medical GmbH
Landsberger Straße 65
82110 Germering
Germany
Tel: [phone]
Fax: [phone]
Internet: www.pathme.de