Nauticam 26306 User manual

Current as of 2022-4-7
26306
2630626306
26306 Mini Flash Trigger for Olympus
Mini Flash Trigger for Olympus Mini Flash Trigger for Olympus
Mini Flash Trigger for Olympus
Instruction Manual
F
FF
F
OREWORD
OREWORDOREWORD
OREWORD
Thank you for your purchase of a NAUTICAM product.
At NAUTICAM, we pride ourselves in the ability to recogni e the
requirements of professional as well as amateur underwater
photographers and fulfill them through the innovative designs of our
products. We strive to achieve a high level of user-friendliness by
allowing stress-free installation and easy operation of all important
functions of the camera.
Please read this manual carefully before using the product, this will
maximi e its performance as well as its lifetime.
W
WW
W
ARRANTY
ARRANTYARRANTY
ARRANTY
All NAUTICAM Products are warranted against any material and
manufacturing defects for two years from the date of purchase for
consumer use. This warranty only applies to products purchased from
authori ed NAUTICAM dealers and does not extend beyond the original
retail purchaser.
To return your product for service, please contact your regional
authori ed service center(s). Please note that this warranty only applies
when the product is purchased in the territory where the service center is
located.
NAUTICAM does not hold responsibility for damage, of any nature, to any
equipment used with and/or placed within our products.
NAUTICAM accepts no liability for any loss of captured images or the
inability to capture images even if it is due to the malfunctioning of our
products.
Unauthori ed modifications and/or repairs of our products will
automatically invalidate the warranty.
RECAUTIONS
RECAUTIONSRECAUTIONS
RECAUTIONS
•Use only batteries approved for use in this product, do not mix old and
new batteries.
•Check the battery terminals before installing into the product.
•Remove batteries for storage, do not store the product in an
environment of high humidity.
•Do not leave the product in direct sunlight for prolonged periods.
•Keep out of reach of children, failure to do so could result in injury.
•Defective products should be shipped to our distributors for service,
unauthori ed disassembling and/or modifications could result in mal-
function.
I
II
I
DENTIFICATION OF
DENTIFICATION OF DENTIFICATION OF
DENTIFICATION OF ARTS
ARTSARTS
ARTS
C
CC
C
OM ATIBLE HOUSINGS A
OM ATIBLE HOUSINGS AOM ATIBLE HOUSINGS A
OM ATIBLE HOUSINGS AND MODULES
ND MODULESND MODULES
ND MODULES
*The flash trigger is shipped without the EM1 and EM5II module from Jul
2021(serial number from A50 8 9 onwards) to reduce unnecessary
waste and impact to the environment. Please contact our dealer or
[e-mail] for the EM1 and EM5II LED Module.
LED
LEDLED
LED
M
MM
M
ODULE
ODULE ODULE
ODULE
I
II
I
NSTALL
NSTALLNSTALL
NSTALLAT
ATAT
ATION
IONION
ION
Choose the required LED module and attach it to the flash trigger base
with the LEDs facing outwards. Make sure the connector on the bottom
of the LED module correctly plug-in to the socket on the flash trigger base.
Secure the LED module by tightening the two supplied screws at the
bottom of the flash trigger.
B
BB
B
ATTERIES
ATTERIES ATTERIES
ATTERIES
I
II
I
NSTALL
NSTALLNSTALL
NSTALLAT
ATAT
ATION
IONION
ION
Make sure the On/Off switch is in the OFF position. Remove the battery
compartment cover by sliding it outwards.
Install the batteries (Panasonic CR2450 x2pcs) with +ve terminal facing
up as shown above. Close the battery compartment cover and then
switch the trigger unit on. The indicator will turn green.
Indicator
IndicatorIndicator
Indicator
Status of flash trigger
Status of flash triggerStatus of flash trigger
Status of flash trigger
Green light
Start up.
Flashing Green
light (1 flash/sec)
Ready to use, normal
operation.
Flashing Red light
(1 flash/sec)
Low
battery warning,
replace batteries.
Image PN Group
Compatible
housings Remark
NA398-01-LED H Group
A
NA-EM5II
NA-EM5III
NA-EM1II
NA-EM1III
NA-EM1X
NA-EM10IV
included in
the package
NA398-01-LED L
- NA-EM1 Not included
in the
package
NA338-01-700-A
NA398-01-038-0-B - NA-EM5II
On/off
switch
Indicator
Battery
compartment cover
Hotshoe connector
Release button
L
ED modules attachment socket
NA398
-
01
-
LED
module
for NA-EM5II/EM5III/EM1II/EM1III/EM1X/EM10IV
Press
Slide

Current as of 2022-4-7
H
HH
H
OUSING
OUSING OUSING
OUSING RE ARATION
RE ARATIONRE ARATION
RE ARATION
Replace the holder as indicated above with the supplied new holder.
Remove the two screws to detach it. Note that NA-EM1II is not required.
For Group A, remove the inner part of the flash on/off lever.
In the rear housing of Group A, locate the flash on/off inner mechanism
(on top of the viewfinder) and then remove the c-clip as indicated above.
Detach the flash on/off inner part and spring from the shaft.
Tip: To remove the c-clip, insert a
nail or a small flat head
screwdriver into the gap as shown
below, then pull it out.
Attention: Keep these parts for
restoring to use with internal flash.
To restore, align the inner part to the shaft with the extruded part on the
left hand side and install the spring and inner part back to the shaft. Then
push the c-clip to the groove on the shaft with a pliers or similar to secure.
Attention: Extra c-clips are provided in the package, DO NOT reuse the c-
clip.
C
CC
C
ONNECT TO THE
ONNECT TO THE ONNECT TO THE
ONNECT TO THE
C
CC
C
AMERA
AMERAAMERA
AMERA
Align the flash trigger hotshoe connector to the camera hotshoe and slide
in until it cannot go in any further. Test the flash trigger by pressing the
shutter release button of the camera, the LEDs in the front should turn on
instantaneously.
To detach the flash trigger from the camera, press and hold the release
button and slide it out.
S
SS
S
ECIFICATIONS
ECIFICATIONSECIFICATIONS
ECIFICATIONS
Construction:
Body: PC+ABS
Dimensions:
Group A
: Approx.
37 x 49 x
42
mm
Weight:
Group A
: Approx. 4
5
g (w/ batteries installed)
Battery:
Panasonic
CR2450 x2pcs
Operation:
This a manual flash trigger only
and has no
TTL function.
Flash Capacity
:
Approx.
10
000times
Compatible
housings:
NA
-
EM1 / EM1II / EM1III
NA-EM5II / EM5IIII
NA-EM1X
NA-EM10IV
Compatible strobes:
INON: Z240 type 4,
Z330
D2000 type 4,
S2000
Sea&Sea: YS-250, YS-D1/D2/D3, YS-01
Remark: Nauticam supports only e-manuals. Please download
corresponding product manuals on Nauticam.com website, or contact
us for e-manuals.
NA
-
EM1
NA
-
EM5II
Screws
Group A
C
-
clip
Spring
Inner part
Screws
Group A