manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Nav TV
  6. •
  7. Recording Equipment
  8. •
  9. Nav TV BMW-EVO KIT NTV-KIT804 User manual

Nav TV BMW-EVO KIT NTV-KIT804 User manual

BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760
www.nav-tv.com i[email protected]m
BMW-EVO KIT
NTV-KIT804
Overview
The BMW-EVO kit interfaces 2 video inputs (including a backup camera) to the factory media
screen in select 2017 BMWs with the NEW GUI (NON-TOUCH SCREEN). This interface generates
steering-based guidelines while in reverse for added convenience. NOTE: the touch-screen
models with this OEM system are not compatible.
Kit Contents
Optional extension cables
7 Series LVDS
extension cable
with coupler:
NTV-CAB122
5 Series LVDS
extension cable
with coupler:
NTV-CAB121
Power/CAN Harness
LVDS Video
cable
BMW-EVO Interface
Remote
(menu control)
IR Eye
Harness
Screen
Connector
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch settings*
Dip SW:
1
2
3
4
5
6
7
8
UP
NO NAV
N/A
N/A
RVC
OFF
N/A
N/A
KEEP
DOWN
KEEP
DOWN
DOWN
ADDING
NAV
N/A
N/A
RVC
ON
N/A
N/A
KEEP
DOWN
KEEP
DOWN
*Note: after adjusting Dip Switches, you must
disconnect and reconnect power to the interface
or the change will not be implemented.
Expansion board
control (optional)
LCD IN (LVDS from
OEM screen)
Dip Switches
(see below)
Power/CAN
OUOUT
RGB INPUT
OUOUT
Digital RGB input (HDMI Adapter)
LCD OUT (Provided
LVDS Cable)
Infrared
Receiver
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
BMW-EVO Interface Installation (5 Series example)
1. The BMW-EVO intercepts two OEM plugs in two locations: the iDRIVE knob and the
screen. You must gain access to both places for proper installation.
a. Access the rear of the screen by removing the dashboard panel (clips only) and
then removing (2x) Torx T20 screws securing the screen to the sub-dash.
2. To access the iDrive harness, remove the panel surrounding it (may have Torx screw
securing to sub dash)
3. Lift up the lower
dash panel and
disconnect 4-PIN plug
powering the iDrive
knob.
4. Connect provided 4-
PIN T-Harness in
between iDrive knob and
OEM harness as shown.
Remove dash
Screen flips up
Remove plastic cover
Remove Torx T20
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4 | P a g e
4. Replace the lower dash panel (with iDrive knob) back to sub-dash.
5. Disconnect the OEM screen LVDS video cable and connect it to the port on the BMW12-N
labeled ‘LCD-IN’.
6. Connect the provided LVDS Video Cable to the port on the BMW12-N labeled ‘LCD-
OUT’ and the other end back to the screen.
7. Install and run the reverse camera video source power and signal to the BMW-EVO interface
location and connect to the RCA labeled ‘CAMERA’. Power your camera with an ACC source or
use the violet wire for reverse 12v (+) only. NOTE: this wire outputs 500 mA MAX –do not use to
supply power to more than 1 camera. Use this wire to trigger a relay if you’re concerned with
current supply.
8. Optional: If installing a secondary camera or AUX video source, connect signal RCA to the
RCA on the BMW-EVO interface labeled ‘AVIN’.
7. After DIP switch settings have been set (see page 2), connect the 24-PIN power connector to
the BMW-EVO interface labeled ‘POWER CAN’. Proceed to Menu Options section if necessary
(front camera settings, etc) or to BMW-EVO Operation.
5 Series
Extension
NTV-CAB121
7 Series
Extension
NTV-CAB122
NOTE: If purchased (separately),
use the LVDS extension cable (with
coupler) from the OEM screen
cable removed from the screen to
the module for convenience.
OR
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5 | P a g e
If adding a front camera OR Aux Video source:
1. Disconnect POWER/CAN Harness from interface
2. Place DIP SWITCH 1 in the DOWN position, reconnect power
3. Press and hold the iDRIVE knob ‘MENU’ to activate the AUX screen
4. Press OK button on remote 4 times, then press POWER
If adding front camera and the user wants it timed (after leaving reverse),
use FRONT CAMERA to set desired time.
If adding front camera or AUX video (no timer), set AV1 to ON using the
arrow keys on the remote (use ‘UP’ to change OFF to ON)
If adding HDMI Adapter, see next page.
Once finished with settings, place DIP SWITCH 1 back into the UP position
and reset power to interface.
Menu Adjustments
Before you start:
•The IR-Eye must be connected
•Make sure the car’s ignition is on and radio is on
•You must be in Reverse Camera mode OR AUX Video mode (see
below):
•
Reverse Camera Mode adjusts Reverse Camera Settings
•
AUX Video Mode adjusts AUX Video Settings
•Press the OK BUTTON 4 times (numbers will display per press),
then press POWER.
•The OSD Menu will appear on screen (auto-time out in about 5
seconds if no action occurs).
Functional Parking Guidelines ON/OFF
Parking Distance Control
ON/OFF (while in reverse)
Adjust FPG Position
Adjust PDC Position
‘Safe to move?’ ON/OFF
PDC
Return
(AUX VID
menu
control)
RVC Menu
AUX
VIDEO
Menu
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6 | P a g e
Adding Optional HD-LINK Adapter (HDMI Input)
Follow the instructions below when adding the HDMI adapter (HD-LINK) to enable HDMI
input to the OEM screen:
1. Put dip switch #1 in the DOWN
position.
2. Activate the ‘NAV INPUT’ by
pressing the ‘MENU’ button
(iDRIVE knob)
3. Once ‘NAV INPUT’ shows on the
screen, on the remote press the
OK BUTTON 4 times, then press
POWER.
4. Navigate to the ‘HDMI’ section.
a. Select ‘OFF’
b. Choose ‘HD95E’
c. Press MODE on the
remote to return and exit
the OSD menu (or let it
time out).
5. Replace dip switch #1 to the UP
position.
6. Connect the black wire to ground
(-) and the red wire to ACC power
(+) from the main power connector
on the HD-LINK adapter. The RCA’s on this plug
provide audio from the HDMI source. See page 8
for a connection diagram.
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7 | P a g e
Green Trigger wire setup
This module includes a green input wire for analog triggering of either the Reverse camera input or the
‘AVIN’ input (yellow RCAs), selectable through the AV menu. This allows for adding multiple cameras
through the use of an SVS-6 switcher, etc. Follow the steps below adjust this feature. NOTE: by default,
the green wire will trigger the Reverse camera input RCA.
1. Put dip switch #1 in the DOWN position. When this section is complete, return switch #1 UP.
2. Activate the ‘NAV INPUT’ by holding the ‘MENU’ button on the iDRIVE knob.
3. Once ‘NAV INPUT’ shows on the screen, on the remote press the OK BUTTON 4 times, then
press POWER.
4. Navigate to the ‘SETTING’ section (6 blocks over).
oSelect ‘REVERSE WIRE’
oChoose ‘AV1’, ‘REAR’ or ‘REAR MODE’
(explanations below)
oPress POWER on the remote to return and
exit the OSD menu (or let it time out).
oTest by sending temporary power (12v +)
to the green wire labeled reverse.
AV1 shows the ‘AVIN’ RCA when the
green reverse wire is triggered.
REAR shows the ‘CAMERA’ RCA
(with no lines) when the green
reverse wire is triggered.
REAR MODE shows the ‘CAMERA’
RCA (with dynamic lines) when the
green reverse wire is triggered.
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
8 | P a g e
BMW-EVO Installation Diagram
BHM
11/20/17
NTV-DOC290
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
9 | P a g e
BMW-EVO Operation
•Once all connections are made and dip switches are set properly, placing the vehicle in
reverse will display the connected camera with dynamic guidelines for convenience.
•Additionally, see below for AUX/Front camera/HDMI activation using factory buttons.
Hold (3 sec): Activate
AUX/Front Camera
video input
Hold (3 sec): Change
AUX/Front Camera view
(60/40 split, etc)
Hold (3 sec) WHEN
IN REVERSE: 2013-
2015 3,5,7,X series:
Change Rear
Camera view
(60/40 split, etc)
Hold (3 sec) WHEN IN
REVERSE: 2013-2015 1
series/MINI: Change
Rear Camera view
(60/40 split, etc)

Other Nav TV Recording Equipment manuals

Nav TV ZEN-A2B User manual

Nav TV

Nav TV ZEN-A2B User manual

Nav TV BMW-EVO ID6 Manual

Nav TV

Nav TV BMW-EVO ID6 Manual

Nav TV AUDI DYNAMIC-A3 User manual

Nav TV

Nav TV AUDI DYNAMIC-A3 User manual

Nav TV NTV-KIT838 User manual

Nav TV

Nav TV NTV-KIT838 User manual

Nav TV W213-N RVC User manual

Nav TV

Nav TV W213-N RVC User manual

Nav TV M650-GM User manual

Nav TV

Nav TV M650-GM User manual

Nav TV M650-GM User manual

Nav TV

Nav TV M650-GM User manual

Nav TV RGB-BNTv2 NTV-KIT903 User manual

Nav TV

Nav TV RGB-BNTv2 NTV-KIT903 User manual

Nav TV W205-H Kit User manual

Nav TV

Nav TV W205-H Kit User manual

Nav TV BMW09N-DYNAMIC User manual

Nav TV

Nav TV BMW09N-DYNAMIC User manual

Nav TV BMW56 User manual

Nav TV

Nav TV BMW56 User manual

Nav TV GM-GVIF Manual

Nav TV

Nav TV GM-GVIF Manual

Nav TV Zen M User manual

Nav TV

Nav TV Zen M User manual

Nav TV NTV-ASY177 User manual

Nav TV

Nav TV NTV-ASY177 User manual

Nav TV VOLVO-CAM 15 NTV-KIT748 User manual

Nav TV

Nav TV VOLVO-CAM 15 NTV-KIT748 User manual

Nav TV GM IO3-PRG User manual

Nav TV

Nav TV GM IO3-PRG User manual

Nav TV ALLGIG-XG User manual

Nav TV

Nav TV ALLGIG-XG User manual

Nav TV MB Sprinter-CAM NTV-KIT477 User manual

Nav TV

Nav TV MB Sprinter-CAM NTV-KIT477 User manual

Nav TV JLR-17+ User manual

Nav TV

Nav TV JLR-17+ User manual

Nav TV ZEN-V User manual

Nav TV

Nav TV ZEN-V User manual

Nav TV RGB-LEX+ NTV-KIT062 User manual

Nav TV

Nav TV RGB-LEX+ NTV-KIT062 User manual

Popular Recording Equipment manuals by other brands

Fostex D-90 owner's manual

Fostex

Fostex D-90 owner's manual

Omega Engineering OM-51 user guide

Omega Engineering

Omega Engineering OM-51 user guide

DINUY EM KNT 002 manual

DINUY

DINUY EM KNT 002 manual

Monitor Technologies SiloPatrol Installation & operation

Monitor Technologies

Monitor Technologies SiloPatrol Installation & operation

ESI MaXiO 032 System manual

ESI

ESI MaXiO 032 System manual

Inovonics 552 Installation & user guide

Inovonics

Inovonics 552 Installation & user guide

SEW-Eurodrive DFP21B manual

SEW-Eurodrive

SEW-Eurodrive DFP21B manual

Rice Lake DeviceNet Series Installation and programming manual

Rice Lake

Rice Lake DeviceNet Series Installation and programming manual

MOTU MicroBook user guide

MOTU

MOTU MicroBook user guide

Axxess AXDSPX-BM1 installation instructions

Axxess

Axxess AXDSPX-BM1 installation instructions

Lexicon PCM 80 Quick reference guide

Lexicon

Lexicon PCM 80 Quick reference guide

Cochlear Baha 3 Fitting Quick Guide

Cochlear

Cochlear Baha 3 Fitting Quick Guide

Shure Microphone Level Tone Generator A15TG user guide

Shure

Shure Microphone Level Tone Generator A15TG user guide

Yamaha VL1-m owner's manual

Yamaha

Yamaha VL1-m owner's manual

TC Electronic Multi-effects Processor G-Natural user manual

TC Electronic

TC Electronic Multi-effects Processor G-Natural user manual

Emerson IEC 62591 instruction manual

Emerson

Emerson IEC 62591 instruction manual

Wavecom GR64 Application note

Wavecom

Wavecom GR64 Application note

Fostex G24S Service manual

Fostex

Fostex G24S Service manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.