Nav TV M650-GM User manual

GM IO5/IO6 M.O.S.T. 50 to RCA, SPDIF & TosLink sound processor
NTV-KIT838
BHM
08/11/17
NTV-DOC303
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

BHM
08/11/17
NTV-DOC303
2 | P a g e
M650-GM Interface
NTV-ASY264
NAV-TV’s M650-GM processor seamlessly converts GM’s MOST-50 audio bus to low level (6 channel) RCA,
S/PDIF or TosLink outputs. Adding an aftermarket amplifier to the OE IO5/IO6 system has never been so easy
or seamless. This plug & play kit integrates with various OEM data networks to retain OnStar, door chimes,
volume control, full fade and balance (analog only), treble, mid-range, bass control & Bluetooth voice calls
with no external speaker (true OEM integration).
M650-GM overview
Overview
Kit Content
Plug & Play T-Harness
NTV-HAR310
USB Cable (updates)
NTV-CAB009
Power/MOST50
connector
LED status
USB (updates)
TosLink output
Coaxial S/PDIF output
FRONT Analog OUT:
Red: Right
White: Left
SUB/CENTER Analog
OUT (mono):
Red: Subwoofer
White: Center
REAR Analog OUT:
Red: Right
White: Left
WARNING: Do not connect any RCA cables to the M650-GM interface or
additional processors prior to properly grounding aftermarket amplifier(s)!
DIP switches

BHM
08/11/17
NTV-DOC303
3 | P a g e
IO5/IO6 OEM GM radio tuner
M650-GM Installation
Proper connection for the M650-GM requires gaining access to the OEM radio tuner module. Known locations
are listed on the chart below:
Vehicle
Radio Tuner Location
ALL Trucks/SUVs
Behind Screen

BHM
08/11/17
NTV-DOC303
4 | P a g e
M650-GM Installation
1. Use the chart on page 3 to locate the OEM radio tuner. Remove all panels/dash pieces to access the
plugs on the OEM radio tuner.
2. Using the provided T-Harness, connect between the proper
connectors (gray 20-pin & gray 8-pin) at the OEM radio tuner
and OEM harness’ from the vehicle.
3. Before connecting power to the M650-GM,adjust dip-switch settings for the desired options:
4. If using analog RCAs to connect to the amplifier, connect FRONT, REAR, SUB/Center to RCA connectors
as shown on page 2. WARNING: Do not connect RCA cables to this interface until all amplifiers/external
processors are properly grounded. Failure to do this may cause damage to the interface and VOID the
warranty!
5. If using S/PDIF for signal to the amplifier, connect to either TosLink or Coaxial connector shown on
page 2. NOTE: both Analog and Digital output sound simultaneously, regardless of which type is used.
6. Use the provided blue wire (extend) for amplifier turn on. NOTE: this wire must be used for amp turn
on, instead of ACC as the amplifier(s) must wake before ignition (for door chimes, etc). This wire will
output 12v whenever a door is unlocked (via remote) or opened (data-sensing). Make certain this wire
will not short circuit anywhere as it will have power any time the vehicle network is active.
Multi-Color LED Status Indication
Position
DIP 1
DIP 2
DIP 3
DIP 4
UP
NO time
alignment
TosLink/SPDIF:
48kHz
OEM BASS adjustment
controls overall BASS
frequencies
Loudness
OFF
DOWN
Driver time
alignment
(trucks only)
TosLink/SPDIF:
96kHz
OEM BASS adjustment
controls SUB output
directly
Loudness
ON
LED Status
Indication
Solid Red
MOST Active
Solid Green
GM-LAN Active
Orange
MOST & GM-LAN Active (normal op)
Violet or White
MOST traffic commands
Blinking Red
Generic Failure
Blinking Blue
PC Link with app (future)
Blinking Green
USB update

BHM
08/11/17
NTV-DOC303
5 | P a g e
M650-GM System Layout Options
TYPE 1: Signal directly to amp, no
additional external processor
TYPE 2: Signal to additional external
processor, then to amplifier