nbf Signature Series User manual

Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and rubber mallet.
800-558-1010
www.NBF.com
Tower w/ Doors • INSTRUCTIONS
CARTONS: ST3330, STD3033
Parts :
ST-A: Back Panel
(30.25” x 28” x 1”)
Quantity: 1
ST-E: Left Side
(15” x 31” x 1”)
Quantity: 1
ST-G: Top
(29.5” x 15” x 1”)
Quantity: 1
ST-B: Shelves
(28” x 13” x 1”)
Quantity: 2
ST-C: Center Support
Quantity: 1
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten all screws/bolts until completely assembled.
Keep all hardware parts out of reach of children.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
Cam Lock Assembly:
To open Cam, point arrow
toward Cam Pin hole. To lock
Cam, turn clockwise.
Figure 1:
ST-H
ST-E
ST-D
DR-F
ST-G
ST-F
ST-H: Base
(28” x 14.25” x 1”)
Quantity: 1
ST-F: Right Side
(15” x 31” x 1”)
Quantity: 1
ST-D: Foot Bracket
(15”D)
Quantity: 2
ST-C
DR-E: Left Door
(14” x 30” x 1”)
Quantity: 1
DR-F: Right Door
(14” x 30” x 1”)
Quantity: 1
DR-E
Tower w/ Doors
Page 1

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
Hardware :
I: Allen Key
Quantity: 1
O: Wood Cam Pins
Quantity: 14
N: 3/4” Wood Screws
(19mm)
Quantity: 23
M: Shelf Pins
Quantity: 8
J: 2.35” Long Bolt
(60mm)
Quantity: 1
Q: Glides
Quantity: 5
P: Cam Caps
Quantity: 14
K: 1.5” Medium Bolts
(38mm)
Quantity: 4
L: 3/4” Short Bolts
(19mm)
Quantity: 4
R: Washers
Quantity: 6
S: Handles
Quantity: 2
T: Hinge
Quantity: 4
U: Hinge
Bracket
Quantity: 4
V: Set of Keys
Quantity: 1
W: Handle Screws
(25mm)
Quantity: 4
X: Latch Screw
(15mm)
Quantity: 2
Y: Lock Latch
Quantity: 1
Z: Door Stop
Quantity: 1
Tower w/ Doors • INSTRUCTIONS
CARTONS: ST3330, STD3033
STEP 1: Insert 1 Wood Cam Pin(O) in the Back Panel(ST-A).
Then, connect the Base(ST-H) to Back Panel(A) by inserting
and locking cams (Figure 1).
NOTE: Cam Locks on Base Panel face away from Back Panel.
ST-A
O
ST-A ST-H
STEP 2: Insert 8 Wood Cam Pins(O) into the Left Side(ST-E)
and Right Side(ST-F).
ST-E ST-F
OO
OO
OO OO
Tower w/ Doors
Page 2

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
Tower w/ Doors • INSTRUCTIONS
CARTONS: ST3330, STD3033
ST-E ST-F
ST-H
STEP 3 : Attach the Left Side(ST-E) and Right Side(ST-F) to the
back and Base(ST-H) by inserting and locking cams (Figure 1).
STEP 4 : Insert 5 Wood Cam Pins(O) into Top(ST-G).
ST-G
OO
O
OO
STEP 5 : Connect the Top(ST-G) to the Left Side(ST-E), Right
Side(ST-F) and the Back Panel(ST-A) by inserting and locking
cams (Figure 1). ST-G
STEP 6 : Insert 1 Glide(Q) into the Center Support(ST-C).
Then, attach the Center Support(ST-C) to the Base(ST-H)
using 4 Short Bolts(L).
ST-E ST-F
ST-A
ST-H
Q
ST-C
STEP 7 : Attach each Foot Bracket(ST-D) to Base Panel(ST-H) by placing 1 Washer(R) between the base and each wood screw hole on
Foot Bracket(Figure 2). Then insert 4 Medium Bolts(K) and 6 Wood Screws(N). Also, insert 4 Glides(Q) into Foot Bracket(ST-D).
Q
Q
Q
Q
K
K
K
K
N
N
N
N
N
N
KN
N
K
N
R
RR
Figure 2
ST-D
ST-H
ST-D
STEP 8 : Insert 8 Shelf Pins(M) and place 2 Shelves(ST-B). Place Cam Caps(P) over cam locks.
Tower w/ Doors
Page 3

STEP 9 : Use 2 Wood Screws(N) to attach each Hinge
Bracket(U) to the sides. The hinge adjustment screw on each
bracket should face toward the back of the unit.
Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
U
U
U
U
STEP 10: Attach the Lock Latch(Y) with 2 Latch Screws(X)
and Door Stop(Z) with 1 Wood Screws(P) to the Top(ST-G).
ZY
X
PX
STEP 11 : Attach 1 Handle(S) to the Left Door(DR-E)
and Right Door(DR-F) with 2 Handle Screws(W) per
handle.
NOTE: Lip on Handle should face down.
S
WW
STEP 12 : Attach 2 Hinges(T) to the Left Door(DR-E) and Right
Door(DR-F) with 8 Wood Screws(N).
N
N
N
N
N
N
N
N
N
N
T
STEP 13A : Connect 4 Hinges(T) to Hinge Brackets(U).
STEP 13B: The screw(EA) located on Hinge Bracket(U) interlocks with the opening on Hinges(T) just as screw(EB) located on
Hinges(T) interlocks with the Hinge Bracket(U) opening. Tighten screw(EA) to secure door.
Note: The screw EB is an adjustment for the door position. Turn right to adjust door to center and left to adjust toward the side.
EA EB
U
T
ST-G
S
WW
DR-F
DR-E
Tower w/ Doors • INSTRUCTIONS
CARTONS: ST3330, STD3033
Hinge
Adjustment
Screw
U
Tower w/ Doors
Page 4

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822
800-558-1010
www.NBF.com
OPTIONAL STEP FOR EXTRA STABILITY ON A 60”x20” LOW CREDENZA
OPTIONAL STEP A : Remove the Glide(Q) from the Center Support(ST-C).
OPTIONAL STEP B: Connect Tower to Low Credenza by inserting Long Bolt(J) through Credenza Top Hole and into the Center
Support(ST-C).
NOTE: THIS CONNECTION WILL PERMANENTLY DISFIGURE THE LOW CREDENZA TOP!
Credenza Top Hole
Low Credenza Top
ST-C
Tower w/ Doors • INSTRUCTIONS
CARTONS: ST3330, STD3033
If you are attaching Tower w/ Doors to Low Credenza, Continue with Optional Step.
Tower w/ Doors
Page 5