NCR 7606-K132 Manual

7606‐K132/K133/138
MemoryModules
KitInstructions
IssueB

Revision Record
Issue Date Remarks
A May 2012 First Issue
B Aug 2012 Added 4GB version (7606-K138)
C Jul 2014 Added 8GB version (7606-K139)

1
Introduction
Thesekitsprovidethevariousincrementsofmemoryavailablefortheterminal.Each
kitcontainsasinglememorymodule.RefertotheMemoryConfigurationtable.
Kit Contents
Thecontentofthekitisasfollowed.
Kit Number Memory Part Number Description
7606-K132 497-0473093 1GB, DDR3, 1333 MHz
7606-K133 497-0473094 2GB, DDR3, 1333 MHz
7606-K138 497-0473095 4GB, DDR3, 1333 MHz
7606-K139 497-0503945 4GB, DDR3, 1333 MHz

2
Installation Procedures
Caution: StaticElectricityDischargemaypermanentlydamageyoursystem.
Dischargeanystaticelectricitybuildupinyourbodybytouchingyourcomputerʹs
caseforafewseconds.Avoidanycontactwithinternalpartsandhandlecardsonly
bytheirexternaledges.
1. DisconnectACpowertotheterminal.
2. Loosenthethumbscrews(2)thatsecuretheTopCover.
3. Slidethecovertowardtherearoftheterminaltoremoveit.
30634
Thumbscrews
31260

3
The7606containsfourDDR3DIMMsockets.Thesocketscanbepopulatedwith
anycombinationofthesupportedmemorymodulesizes(1GB,2GB).Thebase
memorymoduleislocatedinDIMM4.Ifusingmodulesofthesametypethey
shouldbepopulatedaspairsintheDIMMsocketsofthesamecolor.Usethe
followingguideline.
•1Module‐DIMM4(Black)
•2MatchingModules‐DIMM4andDIMM2 (Black)
•3Modules(2Matching)‐DIMM4andDIMM2(Black);DIMM3(Blue)
•4Modules(2Pair)‐DIMM4 andDIMM2(Black);DIMM3andDIMM1(Blue)
Caution: DonotinstallmemorymoduleswhileACpowercordisattached.
1. RemovetheTopCoverandlocatetheDIMMsocket.
2. Openthelatchesattheendsofoneofthesockets.
30650
DIMM1 (Chan A)
DIMM2 (Chan A
DIMM1 (Chan B)
DIMM2 (Chan B)
24189

4
3. AligntheDIMMinthesocketandpushitstraightdownbyapplyingpressureon
theendssmoothlywithbothhandsasindicatedbythearrowsbelow(Notethat
theDIMMconnectoriskeyed)
4. EnsurethattheedgesoftheDIMMengagethelatchesandthatthelatchesare
completelyclosed.
Memory Module Handling Guidelines
The7606usesDDR3typememorymodules.Thesemodulesaremoredelicatethan
othertypesandshouldbehandledwithcare.Followtheguidelinesillustratedbelow
whenhandlingthem.
24190
24192
24269
64C8
24Y02I
220220 220 220
220 220 220 220
220 220 220 220
220 220220220
220 220 220 220
220 2 2 0 220 2 2 0
Do Not Stack Modules
When Packing

5
24271
220220220220220
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
220220
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
220220220220220220220220220220220220
001
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
Do Not Hold Many
at One Time
24273
Do Not Bend
24272
E5108AGBG
-6E-E
06140921A
E5108AGBG
-6E-E
06140921A
Do Not Drop

6
Completethereassemblyoftheterminal.
Afterpoweringuptheterminal,re‐flashtheBIOStoensurethelatestversionis
installedandtoverifythattheterminalisfullyfunctional(seetheBIOSUpdating
ProcedureschapterintheNCRRealPOS82XRTPOSWorkstationUserGuide(B005
00001759).
Note: Youwillseeapromptforterminalmodelandserialnumberinformationifthe
programdetectsinvalidinformationinthecurrentBIOS,orifyouarereplacingthe
Motherboard.
Important:Model/SerialNumberismandatory.