Whalen Victory VIC7PD User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg., Inc. Page 1 Factory No. 96-15197
Victory 7-pc Dining Set (Chair)
Model # VIC7PD
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
Or visit our website www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

Model # VIC7PD
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 2 Factory No. 96-15197
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed
to meet your highest expectations. We guarantee that you will immediately see the value of our fine
furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from
province to province (state to state).
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST, Monday to Friday
www.whalenfurniture.com
1. Maximum load weight on chair is 136 kg (300 pounds).
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
GENERAL INFORMATION, TIPS & TRICKS
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

Model # VIC7PD
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 3 Factory No. 96-15197
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Chair Backrest (2)
B - Seat Frame with Cushion (2) C- Front Leg (4)
(1) Ø5/16" x 1-1/2” Bolt (4+1 extra) (2) Ø5/16" x 3” Bolt (8+1 extra)
(3) Hex Nut (4) Lock Washer (5) Flat Washer
(8+1 extra) (20+1 extra) (20+1 extra)
M5 Allen Key (1) Open Wrench (1)
Tools required: Allen Key and Open Wrench (provided).

Model # VIC7PD
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 4 Factory No. 96-15197
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Lay one Chair Backrest (A) on a smooth and protective surface with the threaded inserts facing up.
3. Place one Seat Frame (B) onto the middle rail of the Chair Backrest (A) with the end dowels fully
inserted. Make sure that the Cushion faces up when the unit is turned upright. Insert the 3” Bolts (2) with
Lock Washers (4) and Flat Washers (5) through the pre-drilled holes on the Seat Frame at rear corner
blocks and loosely screw into the threaded inserts on the Backrest.
4. Secure the Seat Frame (B) onto the Chair Backrest (A) by inserting two 1-1/2” Bolts (1) with Lock
Washers (4) and Flat Washers (5) through the pre-drilled holes on the rear rail of the Seat Frame.
NOTE: DO NOT fully tighten the bolts.
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.
3” Bolt
(4 used in this step)
②
Lock Washer
(6 used in this step)
④
Flat Washer
(6 used in this step)
⑤
1-1/2” Bolt
(2 used in this step)
①

Model # VIC7PD
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 5 Factory No. 96-15197
Assembly Instructions
5. Position the last assembly upside down on the carton or other support surface, as shown.
NOTE: Place a protective cover (like the bubble wrap packing material) over the carton or other support
surface to prevent from scratching.
6. Remove the plastic caps from the hanger bolts of the Front Legs (C). Attach 2 Front Legs (C) to the front
corner blocks of the Seat Frame (B) by inserting the hanger bolts on the Front Leg through the drilled
holes on the corner blocks and fit the Flat Washer (5), Lock Washer (4) and Hex Nut (3) onto each
hanger bolt. Securely tighten the Nuts with the Open Wrench provided.
NOTE: DO NOT fully tighten all the Nuts until the chair been adjust and level all the legs so that they
do not wobble. Once adjusted then go back and tighten while making sure that the unit remains level.
7. Stand the assembled chair upright on a flat surface. Press down the Seat Cushion (B) to even all legs.
Now, tightly fasten all bolts and nuts with the provided Allen Key and Open Wrench.
8. Repeat the same process to assemble the other chair.
Hex Nut
(4 used in this step)
③
Lock Washer
(4 used in this step)
④
Flat Washer
(4 used in this step)
⑤

Model # VIC7PD
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 6 Factory No. 96-15197
Care and Maintenance
zUse a soft, clean cloth that will not scratch the surface when dusting.
zUse of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
zUsing solvents of any kind on your furniture may damage the finish.
zNever use water to clean your furniture as it may cause damage to the finish.
zAlways use coasters under beverage glasses and flowerpots.
zLiquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
zAlways use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
zStains or marks from crayons or ink markers will be difficult to remove.
zIn the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
zCheck bolts/nuts periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for choosing Whalen Furniture!