Neilsen CT2207 User manual

60LB WALK-BEHIND SPREADER CT2207
ASSEMBLY AND OPERATING INSTRUCTIONMANUAL

EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic
safety and health requirements of the EC Directive based on its design
and type, as brought into circulation by us.
In case of alteration of the machine, not agreed upon by us, this
declaration will lose its validity.
Product description: WALK BEHIND SPREADER
Model: CT2207
Applicable EC Directives:
EC Machinery Directive 2006/42/EC
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2016-01-18

Page 2

IMPORTANTINSTRUCTIONS
2. Remove and identify loose parts from carton andbag.
SPECIFICATION
Capacity: 60LB
Dimension of Hopper: 600x295x230mm
Length of Handle: 870mm
Net Weight: 3.3kgs
Wheel Diameter: 12" (300mm)
Poly Wheel
1. HELPFUL HINTS:
READ THE DIRECTIONS BEFORE ASSEMBLY
WHEN ALL ELSE FAILS, READ THE DIRECTIONSAGAIN
Your spreader is designed to be pushed at three miles per hour, which is a brisk walking
speed. Slower or faster speeds will change the spread patterns. Wet fertilizer will also
change the spread pattern and flow rate. Clean your spreader thoroughly after each use.
Wash between the shut off plate and bottom of thehopper.

Page 3

3. ASSEMBLY INSTRUCTIONS
Assembly Step
1. As per Pic. 1, assemble a Flat Washer Ø12, a Bushing, a Poly Wheel on one end of the wheel
axle, which as a Ø3 hole. Then go on assembling a Flat Washer Ø12, at this moment, please
insert a Cotter Pin Ø3X30 into the Ø3 hole on the wheel axle and make the cotter bent for locking.
2. Assemble a Flat Washer Ø12, a Bushing, a Poly Wheel at the other end of the wheel axle.
Turn the wheel till the Ø5 hole on the wheel is in the same line with the Ø5 hole on the wheel
axle, insert the Cotter Pin Ø5X45 and make it bent for locking.

Page 4

Assembly Step
1. As per Pic. 3, insert two Hex Bolt M6X35 with Big Flat Washer Ø6 from the inner hopper and a
leg, then locked by two Wing Nut M6. Tighten the nuts.
2. Using the same way to assemble the other leg. See Pic.4.
Assembly Step
1. As per Pic.5, assemble a Connect Pole onto the top of leg and locked by a Carriage Bolt
M6X35 and a Wing Nut M6.
2. Use the same way to assemble the other Connect Pole. See Pic. 6.

Page 5

M6
ADJUSTING METHOD
Assembly Step
1. As per Pic.7, connect the Handle with Connect Pole, locked by a Hex Bolt M6X30 and a Wing
Nut M6 on the left.
2. On the right, insert the Adjustable Wire into the hole of Index plate, then assemble the Index
plate on the handle and Connect Pole by using Hex Bolt M6x30, Lock Nut M6 and Wing Nut M6.
3. Assemble Wire Crip Bottom Plate on the Connect Pole by using Hex bolt M6x30 and Lock Nut
4. Use the Wire Crip Plate press the Adjustable Wire and Wire Crip Bottom Plate by using Screw
M5x10 and Lock Nut M5. See pic. 8.

Page 6

PARTS DRAWING

PARTS LIST
Ref# Description Qty Ref# Description Qty
1 Screw M5x6 8 21 Screw M5X10 2
2 Scratch Board 2 22 Index Plate Assembly 1
3 Wheel Axle 1 23 Cotter Pin Ø5X45 1
4 Hex Bolt M6X35 5 24 Nylon Lock Nut M6 4
5 Big Flat Washer Ø6 6 25 Wire Lock -1 1
6 Hopper 1 26 Wire Lock -2 1
7 Axle Bushing 2 27 Screw ST.4.8x20 1
8 Flat Washer Ø12 3 28 Carriage Bolt M6X25 1
9 Poly Wheel 2 29 Outer Teeth Washer Ø8 1
10 Cotter Pin Ø3X30 1 30 Spacer 1
11 Bushing 2 31 Adjustable Handle A 1
12 Rotating Door Assembly 1 32 Adjustable Handle B 1
13 Handle 1 33 Screw ST.4.2x18 1
14 Hex Bolt M6X30 4 34 Adjustable Handle Rod 1
15 Connect Pole 2 35 Nylon Washer 1
16 Carriage Bolt M6X35 2 36 Nylon Lock Nut M5 2
17 End Cap 4 37 Lock Washer Ø6 1
18 Support Leg 2 38 Wire Crip plate 1
19 Wing Nut 9 39 Wire Crip Bottom Plate 1
20 Adjustable Wire 1  
Page 7

CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Made in China