Neptronic EVCBM14NIT2S User manual

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
EVCBM14NIT2S-TRL24-TDU-V410-180829-ESL Page | 1
Controller Models
EVCBM14NIT2S (Master controller / 2 TRIACs)
EVCS14N (Slave controller)
TRL Series Thermostat
TRL24 (Room Sensor: Temp)
TRLH24 (Room Sensor: Temp and %RH)
TRLG24 (Room Sensor: Temp and CO2)
TRLGH24 (Room Sensor: Temp, %RH and CO2)
TDU Series Thermostat
TDU10 (Grey LCD, white enclosure)
TDU40 (Black LCD, black enclosure)
TDU70 (Black LCD, white enclosure)
Description
The EVCB Series is a combination controller and thermostat with
support for networked communications via the BACnet MS/TP or
Modbus protocol. The EVCB Series controller is compatible with both
TRL24 and TDU series thermostats. The Networkable Dual Duct VAV
Controller is designed for simple and accurate control of any variable
air volume box in a number of zone control configurations. Its field
configurable algorithms enable versatile implementation of required
control sequences.
EVCB Series
TRL24 Series
TDU10 / TDU40 / TDU70 Series
Typical Application
Applications
Dual duct
oCold and hot duct monitoring
oCold and discharge duct monitoring
oHot and discharge duct monitoring
oPressure independant only
Features
Field configured VAV algorithms, inputs and outputs
Built-in actuator, 70 lb-in
Control external actuators using analog (0-10Vdc, adjustable)
On-board differential pressure sensor
Select direction on analog outputs
Simple air balancing and commissioning via thermostat
Configurable PI (Proportional-Integral) function
Independent, configurable proportional control band and dead
band per ramp
Selectable internal or external temperature sensor (10KΩ)
Activate output with CO2sensor from TRLG24/TRLGH24/TDU or
external sensor input
Internal and external temperature sensor calibration
Freeze protection
Removable, raising clamp, non-strip terminals
Operational Features
Backlit LCD with simple icon and text driven menus
Select thermostat’s default display
Network service port via on-board mini USB connector
Manual night setback or no occupancy override
Multi level lockable access menu and setpoint
Selectable Fahrenheit or Celsius scale
3-wire connection to controller and 4 push keys
Network Communication
BACnet MS/TP or Modbus communication port
Select MAC address via DIP switch or via network
Automatic baud rate detection
BACnet MS/TP®
Automatic device instance configuration
Copy & broadcast configuration via thermostat menu or
via BACnet to other controllers
BACnet scheduler
Firmware upgradeable via BACnet
Support COV (change of value)
Modbus
Modbus @ 9600, 19200, 38400 or 57600 bps
RTU Slave, 8 bits (configurable parity and stop bits)
Connects to any Modbus master

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 2
Controller Specifications
Description
EVCBM14NIT2S
Master
EVCS14N
Slave
Torque
70 in.lb. [8 Nm] at rated voltage
Power consumption
10 VA max
Running time through 90º
90 seconds
Power supply
22 to 26 Vac 50/60 Hz
Inputs
1 input for slave connection (0-10Vdc)
1 input for master connection (0-10Vdc)
1 Universal inputs (Thermistor 10KΩ Type 3,
digital 24Vac/dry contact, or 0-10Vdc)
-
2 digital inputs
-
Outputs
1 output for slave connection (0-10Vdc)
1 output for master connection (0-10Vdc)
1 analog outputs
(0-10 Vdc or 2-10Vdc; selectable)
-
2 TRIAC outputs 24 Vac, 500mA max thermal
fuse in series with each TRIAC output (on/off,
pulse, or 1 floating output)
-
Real Time Clock
Real-time clock (RTC) with super capacitor
backup (approximately 3 days)
-
BACnet
BACnet®MS/TP @ 9600, 19200, 38400 or 76800
bps (B-ASC)
-
Modbus
Modbus RTU slave @ 9600, 19200, 38400 or
57600. Selectable configuration:
No parity, 2 stop bit
Even parity, 1 stop bit
Odd parity, 1 stop bit
-
Communication connection
24 AWG twisted-shield cable (Belden 9841 or
equivalent). Maximum 50ft (15m) between
controller and thermostat
-
Electrical connection
0.8 mm2 [18 AWG] minimum
Operating temperature
0ºC to 50ºC [32ºF to 122ºF]
Storage temperature
-30ºC to 50ºC [-22ºF to 122ºF]
Relative Humidity
5 to 95% non condensing
Weight
1.8 kg. [4 lb]
The actuator performs an auto-stroke on power up. When changing the actuator adjustment screws, cycle power to
initiate the auto-stroke.
EVC with a built-in 70 in. lb. Actuator
Dimensions
A = 2.85” | 73mm
B = 4.85” | 123mm
C = 1.00” | 24mm
D = 2.36” | 60mm
E = 3.27” | 83mm
C
A
B
D

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 3
Thermostat Specifications
Description
TRL24 and TDU Series
Temperature Sensor (TRL24 and TDU)
Setpoint range
10ºC to 40ºC [50ºF to 104ºF]
Control accuracy
Temperature: ±0.4ºC [0.8ºF]
Display resolution
±0.1ºC [0.2ºF]
Humidity Sensor (TRLH24, TRLGH24 and TDU models with Humidity Sensors)
Sensor range
5 to 95%RH
Display resolution
0.1%
CO2Sensor (TRLG24, TRLGH24 and TDU models with CO2Sensors)
Operating principle
Self-calibrating, Non-Dispersive Infrared (NDIR)
Sensor Range
0 to 2000 ppm
Setpoint range
100 to 2000 ppm
Accuracy
±30 ppm ±3% of reading
Response time
2 minutes by 90%
Display resolution
1 ppm
Other
Electrical connection
3 wires to VAV controller and 2 wires to BACnet/Modbus network | 0.8 mm2 [18 AWG] minimum
Network service port
Mini USB connector
Power supply
24Vac
Power consumption
1VA
Operating temperature
0ºC to 50ºC [32ºF to 122ºF]
Storage temperature
-30ºC to 50ºC [-22ºF to 122ºF]
Relative humidity
5 to 95 % non condensing
Enclosure protection
IP 30 (EN 60529)
Weight
120 g. [0.25 lb]
Dimensions
TRL24
TDU
A = 2.85” | 73mm
B = 4.85” | 123mm
C = 1.00” | 24mm
D = 2.36” | 60mm
E = 3.27” | 83mm
A = 4.94” | 125mm
B = 2.87” | 72.8mm
C = 3.44” | 87mm
D = 1.22” | 31mm
E = 0.75” | 19 mm
F = 2.00” | 51mm
G = 2.18” | 55mm
A
B
C
D
E
F
G
R.095 TYP
R6.542 TYP
A
B
C
D
E

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 4
Interface
TRL24
Cooling ON
A: Automatic
Communication Status
Alarm status
Heating ON
A: Automatic
Menu Locked
Energy saving mode
(NSB or Occupancy)
Fan ON
A: Automatic
Programming mode
(Technician setting)
Percentage of
humidity
or
ºC: Celsius scale
ºF: Fahrenheit scale
TDU
Network
Communication
User Lock
Programming Mode
(Technician Setting)
Alarm Status
Energy Saving
Mode (NSB/OCC)
Schedule
Time
ppm
Parts Per Million
°C
°F
%RH
ºC: Celsius Scale
ºF: Fahrenheit Scale
%RH :Humidity
A
Automatic Mode
Cooling
Heating
Fan
BACnet or Modbus Address DIP Switch (DS1)
MAC address for communication, are selectable by DIP switch using binary logic. If you do not change device instance in program mode, it will be
automatically modified according to the MAC address.
Note: Avoid using addresses above 246 when selecting Modbus MAC address.
MAC Address
DS.1 = 1
DS.2 = 2
DS.3 = 4
DS.4 = 8
DS.5 = 16
DS.6 = 32
DS.7 = 64
DS.8 = 128
Default Device Instance
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
153000
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
153001
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
153002
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
153003
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
153004
…
…
…
…
…
…
…
…
…
…
126
OFF
ON
ON
ON
ON
ON
ON
OFF
153126
127
ON
ON
ON
ON
ON
ON
ON
OFF
153127
* Slave addresses available by setting DS.8 to ON
C
F
%RH
MO TU WE TH FR SA SU
AM PM
.
.
.
.
%RH
C
F
AM
PM
%RH
F
C
123456 7

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 5
Mounting Instructions
TRL24
CAUTION: Remove power to avoid a risk of malfunction.
A. Remove the captive screw that’s holding the base and the front cover of the unit together.
B. Lift the front cover of the unit to separate it from the base.
C. Pull all wires through the holes in the base.
D. Secure the base to the wall using wall anchors and screws (supplied). Make the appropriate connections.
E. Mount the control module on the base and secure using the screw.
TDU
CAUTION: Remove power to avoid a risk of malfunction.
A. Remove the wall mounting plate (highlighted) from the back of the thermostat.
B. Install the mounting plate on the gang box.
C. Pull the wires through the base hole and make the appropriate connections.
D. Mount the thermostat onto the wall plate. To mount the thermostat correctly, place the top of the thermostat on the mounting plate
first and push it into the grooves to snap it into place.
E. Secure the thermostat using the screw (supplied).
A
E
D
C
B
ABCE
D

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 6
Wiring
We strongly recommend that all Neptronic products be wired to a separate grounded transformer and that transformer shall service only
Neptronic products. This precaution will prevent interference with, and/or possible damage to incompatible equipment.
DS1 DIP Switch
The 8 DIP switches
represent a binary logic to
calculate the MAC address.
Default = all OFF
TB1 TB3TB2 TB4 TB5 TB6
Power Status
ON
1 2 3 4 5 6 7 8
DS1
TB7
INT EXT
JP1
Optional: connect
to enable service port
3 2
AI2
COM
1 analog input –(AI2 config.)
Externaltemp,normally cool/heat, setpoint
air flow, CO2, air supply temp
3 2
AO2
COM
1 analog output (AO2 config.)
Coolramp 1 or2, heat ramp 1 or2, CO2
3 2 1
DI2
DI1
COM 2 digital inputs (config.)
DI2: Override, normally cool/heat
DI1: OCC open/close, NSB open/close
3 2 1
COM
24Vac input
(TO2/TO1)
TO1
4
TO22 TRIAC outputs (config.)
Cool 1 or 2, heat1 or 2, CO2
On/Off (config close/open percent)
Floating (config float time)
Pulse (heat only)
Direct or reverse
3 2 1
Data
COM
Pwr
3 2 1
COM
A+ (in)
B- (in)
5 4
A+ (out)
B- (out)To other
BACnet
devices
High Total Pressure
Low Static Pressure
TXD RXD JP3 EOL
JP1(TO1 / TO2 input voltage)
INT = 24Vac supplied internally by TB1
EXT = Apply 24Vac to pin 1 of TB2
TB1 TB4 TB5
Power
2
COM
2
COM
3 1
24Vac
COM
Power Input
24Vac
Power On = 24Vac applied to
TB1
EVCBM14NIT2S
(Master)
EVCS14N
(Slave)
3
AO2
1
AI1
1
AO1
1
AI1
XFO
Line
Voltage
L
N
24Vac
3
24Vac
1
COM
4
24Vac
2
COM
4
24Vac
2
COM
MASTER
SLAVE
TB1
Data
COM
Pwr
Important:
Use the same transformer for
both the Master and Slave.
JP3(End of line)
None = No end of line
120 Ohms = Last node on network
TXD Flash
transmitting data via network
RXD Flash
receiving data via network
Power On
24Vac applied to TB1
Status Flash
communicating via thermostat
TRL24 and TDU
1
2
3
4
5
6
7

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 7
PCB Drawings
TRL24 Thermostat
3 wire cable (TB1 #1, 2 & 3)
Connect TB1 #6 (A+) & #7 (B-) to EVCB to enable the BACnet service port.
Mode Selection (JP1)
RUN:
Thermostat is in Operation Mode.
Thermostat must be set in this mode for
normal system operation. If not locked,
setpoint and control mode can be changed
by the end user.
PGM:
Thermostat is set in Programming Mode.
Refer to the following sections for more
details.
TDU Thermostat
3 wire cable (TB1 #1, 2 & 3)
Connect TB1 #6 (A+) & #7 (B-) to EVCB to enable the BACnet service port.
Mode Selection (JP1)
RUN:
Thermostat is in Operation Mode.
Thermostat must be set in this mode for
normal system operation. If not locked,
setpoint and control mode can be changed
by the end user.
PGM:
Thermostat is set in Programming Mode.
Refer to the following sections for more
details.
Access to Menus
The menu overviews and options are the same for both TRL24 and TDU thermostats. However, the action key or the key used to
access the menus and save changes is different in the thermostats. Use the following menu overviews with the appropriate action key
as per your thermostat.
Action Keys on Thermostat
Action Key
Task
TRL24
TDU
Press to access the programming menus and save any changes.
Press to return to the previous step without saving.
Mode Selector Jumper
RUN = Operation Mode
PGM = Programming Mode
BACnet
service port
Avoid touching the CO2
sensor as this may cause
incorrect readings
TB1
1
2
3
4
5
6
7
PGM RUN
A
B
C
JP1
Optional: connect
to BACnet network to
enable service port
CO2sensor
(TRLG24 and TRLGH24 only)
A+
DATA
PWR
COM
B-
Connect to VAV
controller
Temperature sensor (all models)
Humidity sensor (TRLH24 and TRLGH24 only)
PGM
RUN
JP1
PGM
RUN
JP1
Mode Selector Jumper
RUN = Operation Mode
PGM = Programming Mode
BACnet
service port
JP1
PGMRUN TB1
Optional: connect
to BACnet network to
enable service port
A+
DATA
PWR
COM
B-
Connect to EVCB
1 2 3 4 5 6 7
CO2sensor
(models with CO2sensors)
Avoid touching the CO2
sensor as this may cause
incorrect readings Temperature sensor (all models)
Humidity sensors (models with humidity
sensors)
PGM
RUN
JP1
PGM
RUN
JP1

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 8
Pressure & Inputs –Menu (1 of 4) | Pressure and Inputs (AI1, AI2, DI1, DI2)

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 9
Outputs –Menu (2 of 4) | TO1, TO2, AO1, AO2

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 10
Settings –Menu (3 of 4) | Temp, Motor, Settings and Ramps

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 11
Settings –Menu (4 of 4) | Network, Time and Options

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 12
Reset to Factory Default Settings
This will erase all actual configurations and replace them with the factory default settings.
1. The Mode Selector jumper (JP1) of the thermostat must be set to the “RUN” position (Operation Mode). Refer to Wiring on page 6.
2. During the power up sequence of the controller and thermostat (when the firmware versions are displayed), press and hold both the
and keys.
3. The “Enter Password” screen appears. Enter 372 within 1 minute by using the arrow keys to increase or decrease the value and the
[ / ] and keys to toggle between the digits.
4. Use the arrow keys to select YES and then press [ / ].
Menu 372 –Temperature Offset
1. This menu is accessible through normal operation mode. The Mode Selector jumper (JP1) of the thermostat must be set to the
“RUN” position (Operation Mode). Refer to Wiring on page 6.
2. Press the [ / ] and keys simultaneously for 5 seconds. The “Enter Password” screen appears.
3. Enter the password within 1 minute by using the arrow keys to increase or decrease the value and the [ / ] and keys
to toggle between the digits.
a. Password 372 = Temperature Offset Menu
4. If you enter the wrong password, the thermostat displays “Eror” and returns to Operation Mode. The thermostat will return to
normal mode if you navigate through the entire menu and do not make any selection, or if you do not press any key for 5 minutes.
The changed values will be saved automatically.
1. “Intern Temp Sensor Offset”
Range:
Offset:
Increment:
10 to 40ºC [50 to 104ºF]
Max ± 5ºC
0.1ºC [0.2ºF]
Compare the displayed temperature reading with a known value from a thermometer. To offset or calibrate the sensor, use the
arrows key to set the desired temperature reading. This is useful for thermostats installed in areas where the temperature read is
slightly different than the room’s actual temperature. For example, a thermostat placed right under the air diffuser.
If the thermostat is set to use an external temperature sensor (EtS), the thermostat displays “OFF”.
2. “Extern Temper Sensor Offset”
Range:
Offset:
Increment:
0 to 50ºC [41 to 122ºF]
Max ± 5ºC
0.1ºC [0.2ºF]
This option appears if you’ve set one of the analog inputs to EtS (External temperature sensor). When the thermostat is connected
to the appropriate analog input, the display shows the temperature read by the external temperature sensor. Adjust the offset by
comparing it with a known value (e.g. thermometer). If the sensor is not connected or short circuited, then the unit displays the
sensor's limit.
3. “Input3 Reading”
Range:
250mV (0") to 4000mV (1")
Displays the voltage output value in mV of the pressure sensor.
4. “Input3 Minimum Reading
Range:
Default:
10mV to 180mV
60mV
This setting represents the deadband of the pressure sensor in mV. For advanced users or special applications only. We
recommend that you use the default setting of 60mV.

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 13
Menu 637 –Network Settings
This menu is accessible through normal operation mode. The Mode Selector jumper (JP1) of the thermostat must be set to the “RUN” position (Operation Mode). Refer to Wiring on
page 6.
Note: Since the action keys are different on TRL and TDU thermostat series, both keys have been included in the instructions. Refer to the Action Keys on Thermostat section to
know and use the key as available on your thermostat.
1. Press the [ / ] and keys simultaneously for 5 seconds. The “Enter Password” screen appears.
2. Enter the password within 1 minute by using the arrow keys to increase or decrease the value and [ / ] and keys to toggle between the digits.
a. Password 637 = Network Settings Menu
3. If you enter the wrong password, the thermostat displays “Eror” and returns to Operation Mode. The thermostat will return to normal mode if you navigate through the entire
menu and do not make any selection, or if you do not press any key for 5 minutes. The changed values will be saved automatically.

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 14
Menu 757 –Airflow Balance Mode
1. This menu is accessible through normal operation mode. Set the thermostat Mode Selector jumper (JP1) to the “RUN” position (Operation Mode). Refer to Wiring on page 6.
1. Press the [ / ] and keys simultaneously for 5 seconds. The “Enter Password” screen appears.
2. Enter the password (757) within 1 minute by using the arrow keys to increase or decrease the value and the [ / ] and keys to toggle between the digits.
3. If you enter the wrong password, the thermostat displays “Eror” and returns to Operation Mode. The thermostat will return to normal mode if you navigate through the entire
menu and do not make any selection, or if you do not press any key for 5 minutes. The changed values will be saved automatically.

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 15
Operation Mode
The Mode Selector Jumper (JP1) of the thermostat must be set to the “RUN” position (Operation Mode). Refer to Wiring on
page 6.
TRL24
TDU
Press to toggle
between °C and °F
Actual demand
C
Appears if setpoint
adjustment is locked
Change setpoint
value
C
Press once to
display control mode
Press for 5 sec.
to display air flow
(if using pressure sensors )
Exits after 5 sec. Exits after 3 sec.
Press twice to
display setpoint
Setpoint
value
Press to change mode :
- Auto
- Off
- Cool only
- Heat only
Appears if in Night Setback (NSB) or Occupancy
(OCC) mode. Flashes if overridden by user .
CO2reading in ppm
(CO2display option must be enabled in
programming mode )
%RH
Room
temperature Alternates between room temperature for 8 sec
and then room humidity for 2 sec.
(requires Humidity sensor thermostats )
Toggle between :
- Airflow 1 (master)
- Airflow 2 (slave)
- Airflow 1 setpoint (master)
- Airflow 2 setpoint (slave)
- Air supply temp
Exits after 5 sec.
C
Actual demand
Room
temperature
Appears if inNight Setback (NSB) or
Occupancy (OCC) mode. Flashes if overridden
by user.
%RH
Alternates between room temperature for 8 sec and then
room humidity for 2 sec.
(requires Humidity sensor thermostats)
Press for 5 sec.
to display air flow
(if using pressure sensors ) Press to toggle between
°C and °F
Press once to display
control mode
C
Scroll through the following values :
- Airflow 1 (master)
- Airflow 2 (slave)
- Airflow 1 setpoint (master)
- Airflow 2 setpoint (slave)
- Air supply temp
Exits after5 sec. Exits after5 sec.
Press to change mode:
- Auto
- Off
- Cool only
- Heat only
CO2reading in ppm
(CO2display option must be enabled in
programming mode )
Press twice to
display setpoint
Appears if setpoint
adjustment is locked
Change setpoint value
Setpoint value
Exits after 3 sec.

Networkable Dual Duct VAV Controller
Specification and Installation Instructions
www.neptronic.com EVCBM –Dual Duct Page | 16
Power Up
Upon power up, the LCD illuminates and all segments appear for 2 seconds. The thermostat then displays its current version of the
thermostat for 2 seconds followed by the current version of the controller for 2 seconds. Pressing any key on the thermostat illuminates
the LCD for 4 seconds.
CO2(Thermostats with CO2 Sensors)
If enabled via the configuration menu, the thermostat displays the CO2reading on the first line above the temperature reading. If CO2
display is enabled, the time will not be displayed.
Temperature Display and Setpoint
If enabled in the "Display Info" menu (see Settings –Menu (3 of 4) | Temp, Motor, Settings and Ramps on page 10), the thermostat
displays the temperature reading. If the sensor is disconnected or short circuited, then the unit displays the sensor's limit. To toggle the
temperature scale between ºC and ºF, press the key. To display the setpoint, press the or key twice. The setpoint appears
for 5 seconds. To adjust the setpoint, press the arrow keys while the temperature is displayed. If the setpoint adjustment has been
locked “Setpnt Locked”, the lock symbol appears.
Humidity
If enabled in the "Options" menu (see Settings –Menu (4 of 4) | Network, Time and Options on page 11), the thermostat displays the
temperature reading for 8 seconds and then displays the humidity reading for 2 seconds. If the sensor is disconnected or short circuited,
then the unit displays the sensor's limit.
Airflow and Air Supply Temperature
Press and hold the [ / ] key for 5 seconds and use the arrow keys to view the “airflow 1”(master), “airflow 2”(slave), “airflow
Setpnt 1" (master), “airflow Setpnt 2" (slave), and “air Supply Temp”. After 5 seconds without any action, the thermostat returns to
operation mode. The air supply temperature appears only if analog input AI1 or AI2 are configured with the AST option.
Control Mode
To access the Control Mode, press the [ / ] key. The Control Mode appears for 5 seconds. Press the [ / ] key to scroll
through the following control modes. These options can vary depending on the options selected in "Temp Control Mode" and "Enable
OnOff Control Mode".
Auto (Automatic Cooling or Heating)
OFF (if it is not disabled in Programming Mode)
Cooling only (on, with cooling symbol)
Heating only (on, with heating symbol)
Night Setback (NSB) or Occupancy Mode
This function is only available if you set DI1 to nSb (Night setback contact) or Occ (occupancy mode). If the DI1 contact is triggered, the
thermostat enters NSB or No Occupancy Mode (the symbol appears) and uses the NSB or OCC heating and cooling setpoints.
If not locked, you can override the night setback or no occupancy mode for a predetermined period by pressing any of the 4 keys.
During the override period the symbol will flash. If the symbol does not flash, the override period is finished or the night setback or
no occupancy override has been locked in programming mode.
Set Time and Date
1. Ensure that JP1 on the thermostat is set to Run.
2. Press and hold the key for 5 seconds
3. Use the arrow keys to set the desired value. Press the [ / ] key to save and got to the next step. Press the key to go
to the previous step without saving.

Notes

Recycling at end of life: please return this product to your Neptronic local distributor for recycling. If you need to find the nearest
Neptronic authorized distributor, please consult www.neptronic.com.
400 Lebeau blvd, Montreal, Qc, H4N 1R6, Canada
www.neptronic.com
Toll free in North America: 1-800-361-2308
Tel.: [phone]
Fax: [phone]
Customer service fax: [phone]
Monday to Friday: 8:00am to 5:00pm (Eastern time)