NetComm 3G41WT User manual

3G41WT Quick Start Guide
NETCOMM LIBERTY™ SERIES
3G/4G USB Gateway

This gateway has been designed to be placed on a desktop. All of the cables exit from the
rear for better organization. The LED indicator display is visible on the front of the gateway to
provide you with information about network activity and the device status. See below for an
explanation of each of the indicator lights.
ICON LABEL ICON DESCRIPTION
Power Lights up when the gateway is powered on
WiFi Lights up when the gateway is distributing a WiFi signal
LAN/WAN Lights up when a device is plugged into the LAN/WAN port
LAN 2-4 Lights up when a device is plugged into one of the LAN ports
WWW Lights up when the gateway is connected to the Internet
Signal Lights up with an active mobile broadband connection
Signal Strength Lights up indicating the current mobile broadband signal strength

REAR PANEL DESCRIPTION
1 Reset button By using a paper clip, hold this button down for more than 10 seconds to
reset to factory defaults.
2 DC IN Power connector, connects to a DC 12V 1.5A Power Adapter
3 LAN/WAN port RJ-45 LAN/WAN port for wired Ethernet clients (LAN) or alternate Internet
connection to ADSL/Cable/Fibre (WAN)
4 LAN ports 3 x RJ-45 LAN ports for wired Ethernet clients (computers, laptops, etc)
5 USB ports Two USB 2.0 ports for connection to mobile broadband USB modem (LTE
dongle) and/or USB external hard drive for le sharing
1
5
4
3
2

1
Hardware Installation
1. If you are using a mobile broadband connection, attach your USB modem to the USB
port on the side of the 3G/4G USB Gateway.
2. Connect the power adapter to the power socket on the back of the 3G/4G USB Gateway.
3. Plug the power adapter into your power point and switch on the power.
4. Wait approximately 60 seconds for the 3G/4G USB Gateway to power up.
Power adapter
Power point

2
Connecting to the Gateway
via a Cable
NOTE: This step is optional. If you do not wish to connect via an Ethernet cable to the Gateway, please skip this step and
proceed to step number 3.
1. Connect the yellow Ethernet cable provided to one of the Ethernet ports on the back of
the 3G/4G USB Gateway.
2. Connect the other end of the Ethernet cable to your computer or to another
Ethernet-enabled device like a gaming console, a TV or a home cinema system.
3. Wait approximately 30 seconds for the connection to establish.
Computer

Smart Phone
Online Gaming
Laptop
Tablet
3
Connecting to the Gateway
via WiFi
NOTE: This step is optional. If you do not wish to connect via WiFi to the Gateway, please skip this step.
You can connect multiple WiFi devices, including laptops, desktops, tablets and PDA’s to your
Gateway by following these two basic steps.
1. Using your WiFi device, scan the WiFi networks in your area and select the wireless
network name listed on the included Wireless Security Card and then click connect.
2. Enter the wireless security key listed on the included Wireless Security Card.

Attention BigPond Users
BigPond Mobile Broadband services require a user name and password, issued to you by
BigPond at the time of purchase, which must be entered into your 3G/4G USB Gateway
before use. Please follow the steps below to setup your BigPond connection:
1. Login to the web based management console by opening your web browser (Internet
Explorer/Firefox/Safari) and navigate to the address http://192.168.20.1.
2. On the basic view, click the “Login” tab and enter “admin” (without quotes) into the
Username and Password elds and click submit.
3. Click the “Internet” tab and unselect the checkbox labelled “Automatically congure my
mobile broadband”.
4

4. Check and ensure “Australia” is shown underneath the Custom APN eld.
5. From the “Choose an APN here” pull down menu, mouse over to “Telstra” and select
“telstra.bigpond” as the APN.
6. Click on the sentence “Click here if your service requires a Username and Password” and
enter the Username and Password as supplied by BigPond and click “Save”.
7. Click the “Save” button at the bottom of the page to store the new conguration settings
and connect to the BigPond Mobile Broadband service.

Attention Telstra
IPWAN Customers
Telstra IPWAN Mobile Broadband services require a user name and password, issued to you
by Telstra at the time of purchase, which must be entered into your 3G/4G USB Gateway
before use. Please follow the steps below to setup your Telstra connection:
1. Login to the web based management console by opening your web browser (Internet
Explorer/Firefox/Safari) and navigate to the address http://192.168.20.1.
2. On the basic view, click the “Login” tab and enter “admin” (without quotes) into the
Username and Password elds and click submit.
3. Click on the “Switch to advanced view” link at the bottom of the page.
4. Click on the “Internet Settings” menu at the top of the page, select the rst menu option
labelled “Mobile Broadband” or “WWAN” and then select “Connection.”
5

5. Unselect the checkbox labelled “Automatically congure my mobile broadband”.
6. Type in the APN required for your service (e.g telstra.corp), or select from the “Choose an
APN here” pull down menu.
7. Enter the Username and Password as supplied by Telstra.
8. Select “Disable” for the NAT Masquerading option*.
9. Click the “Save” button located under the NAT Masquerading option to store the new
conguration settings and connect to the Telstra IPWAN Mobile Broadband service.
* Enabling/disabling NAT Masquerading is dependent on your individual network setup