Netech UniMano 1000 800 Series User manual

UniMano 1000
Pressure Vacuum Series
800-Series
July 2009
UniMano 1000 Series

INSTRUCTION MANUAL
FOR
800-2000
800-4000
800-5000
110 Toledo Street
Farmingdale N.Y. 11735
Phone: [phone] Fax: [phone]
www.netech.org
Copyright
Copyright © 2003 by Netech Corporation. All rights reserved. No part of this
publication may be reproduced or transmitted in any form other than for the
purchaser’s personal use without written permission from Netech
Corporation.
Quality Assurance
Netech Corporation is ISO 9001-2000 Registered. This instrument was
thoroughly tested and inspected according to Netech’s ISO 9001-2000
quality standards (ISO/IEC 17025) and test procedures, and was found to
meet those specifications when it was shipped from the factory.
UniMano 1000 Series 2

Warranty
Netech warranties the UniMano 1000 Series Pressure Meters against defects
in materials and workmanship for one year from the date of original
purchase.
During the warranty period, we will repair or, at our option, replace at no
charge a product that proves to be defective, provided you return the product
shipping prepaid to Netech Corporation. This warranty does not apply if the
product has been damaged by accident or misuse, or as the result of service
or modification by other than Netech Corporation, or if its serial number is
defaced or removed.
Netech reserves the right to discontinue the UniMano 1000 Series Pressure Meters
at any time, or change its specifications, price, or design without notice and
without incurring any obligation. Netech will make a concerted effort to supply
service parts for 5 years after discontinuation.
The warranty is void if you elect to have the unit serviced and / or calibrated
by someone other than Netech.
The purchaser assumes all liability for any damages or bodily injury that
may result from the use or misuse of the unit by the purchaser, his
employees, agents or customers.
In no event shall Netech Corporation be liable for consequential
damages.
UniMano 1000 Series 3

Table of Contents
General Overview
Introduction----------------------------------------------------- 05
Specifications--------------------------------------------------- 05
Accessories------------------------------------------------------ 07
Optional Accessories------------------------------------------- 07
General Operation
Controls and Indicators --------------------------------------- 08
Precautions ---------------------------------------------------- 09
Normal Operation --------------------------------------------- 10
Peak Operation ------------------------------------------------ 11
Set Operation -------------------------------------------------- 12
Leak Detection ----------------------------------------- 12
Alarm Mode -------------------------------------------- 12
Simple Troubleshooting Guide ------------------------------ 13
Typical Application Set Up ---------------------------------- 13
Test And Calibration
Factory Calibration ------------------------------------------- 14
UniMano 1000 Series 4

GENERAL OVERVIEW SECTION 1
1.1 INTRODUCTION
GENERAL DESCRIPTION
The UniMano 1000 is an advanced microcontroller based, compact, high performance
pressure and vacuum meter designed for very precise measurement and calibration of
pressure and vacuum in medical, laboratory and industrial applications. The UniMano 1000
combines such features as fluid compatibility, temperature compensation, linearity correction,
leak detection, peak hold, over pressure alarm and user selectable units of measurement. It is
menu driven and simple to operate. All the functions are set from a 2 line, 16 character LCD
display and a key pad with 8 tactile keys. Using state of art technology, the UniMano 1000
provides superior accuracy and performance. Many software upgrades will be made available
to accommodate additional features and advanced functions.
1.2 SPECIFICATIONS
Display:
2 Line 16 character LCD.
Polarity Display:
The negative sign (-) is displayed when there is a vacuum reading.
Accuracy:
0.1% full range, +/- 1 count (Pressure Only).
Operating Temperature:
0 degree C to 50 degree C
Media Compatibility:
Non-corrosive fluids and gases
Maximum Pressure:
Double the rated Pressure.
Power:
One 9 volt alkaline battery or optional AC adapter (PN:302).
Low Battery Indicator:
Audio and visual display if battery voltage is ≤6.8 volts. Unit will go into sleep
mode.
Physical Dimensions:
Size: 5.5 x 3.5 x 1.5 in (13.75 x 8.75 x 3.75 cm)
Weight: 10 oz (.28 kg)
UniMano 1000 Series 5

Range and Resolution for UniMano 1000 Standard Models:
800-2000
Unit Pressure Vacuum Resolution
MmHG 1500 517 0.5
inH2O 800 276.9 0.3
MBar 2000 689.7 0.7
cmH2O 2100 703 0.7
KPa 200 68.97 0.07
InHg 60 20.36 0.02
Psi 30 10 0.01
kg/cm22 0.703 0.0007
800-4000
Unit Pressure Vacuum Resolution
MmHG 3000 517 1
inH2O 1600 277 1
MBar 4100 690 1
cmH2O 4200 703 1
KPa 400 69 0.2
InHg 120 20.4 0.1
Psi 60 10 0.02
kg/cm24 0.704 0.002
800-5000
Unit Pressure Vacuum Resolution
MmHG 5000 517 1
inH2O 2700 277 1
MBar 6800 690 1
cmH2O 7000 703 1
KPa 690 68.9 0.1
InHg 200 20.4 0.1
Psi 100 10 0.1
kg/cm27 0.703 0.001
UniMano 1000 Series 6

1.3 ACCESSORIES
Description Part Number
User Manual 800-Manual
1.4 OPTIONAL ACCESSORIES
Description Part Number
110 VAC Adapter 302
220 VAC Adapter 302-220
Syringe Pressure Applicator 204
Tubing And Connector Set 203
Soft Carrying Case 501
UniMano 1000 Series 7

OPERATION SECTION 2
2.1 CONTROLS AND INDICATORS
1. Display Screen
2. ON/OFF Key Pad
3. Function Selection Keys
4. Scroll Functions Keys
5. Luer Lock Fitting (Female)
6. Function Menu Key
7. AC Adapter Input
8. Zero Adjust (R11)
9. Fine Gain Adjustment
5
1
3
4
4
2
6
UniMano Pressure Meter
Figure 1
UniMano 1000 Series 8

7
8
Side Views
9
Figure 2
2.2 PRECAUTIONS
Because the UniMano 1000 is both a Pressure and a Vacuum Meter it will read below
zero identifiable by the negative sign in front of reading.
Do not exceed the rated maximum pressure of the instrument, although a transient
pressure of two times the rating will generally be tolerated.
Do not connect the instrument to corrosive gases or highly ionic fluids.
Do not continue to use if the instrument is wet.
If the battery voltage is lower than 6.8 Volts “Battery Low” warning will be
displayed. The UniMano 1000 will beep twice, to warn the user to turn the unit off.
The microcontroller will go into a sleep mode thereby disabling any pressure
measurements.
Do not use any other AC adpters as this will damge the unit.
UniMano 1000 Series 9

2.3 NORMAL OPERATION
Press the ON/OFF to activate the UniMano 1000. On startup the microcontroller will
initiate a self check, beep and briefly display the Model and Version of software.
UniMano UM5000
100PSI
Ver 2.0
The display will then revert to:
00.00 PSI
unt
zro
peak
set
Allow two minutes for the transducer to warm up and stabilize.
The top line is your measurement line and the second line is your select function line.
Press an [F] key to select which function you wish.
unt: Different Units of Measurements
zro: Zeroing the display
peak: Peak value capture
set: Alarm and Leak Detection
The 800-2000 will turn on in the mmHG unit of measurement, while both the 800-
4000 and 800-5000 default to the PSI unit of measurement.
To select another engineering unit to be displayed simply press [F1] and the display
will show the various units of measurements available.
< 00.00 PSI >
Kpa
iHg
psi
Kgc
Kpa: KiloPascal
iHg: Inches of Mercury
psi: Pounds per Square Inch
Kgc: kilogram-force/square centimeter
mmHg: millimeters of Mercury
iHo: inches of Water
mBr: milliBars
cHo: centimeters of Water
UniMano 1000 Series 10

Use the [<] or [>] keys to bring your choice to the display and then press the
appropriate [F] Key to select your choice. For example pressing [F1] for kilopascal.
Once your unit of measurement is selected you can press [MENU]
000.1 KP
A
unt
zro
peak
set
Your display should revert back to your basic functions
With no pressure applied, the display should read zero, if not, press [F2] to
automatically adjust the zero.
000.0 KP
A
unt
zr
o
peak
set
Once the UniMano is zeroed you may apply pressure and the display will accurately
show the actual pressure applied in your selected unit of measurement.
2.4 PEAK OPERATION
If your input pressure is variable and you wish to see the highest value obtained over
a period of time simply press [F3] or peak. On the display the function “peak” will
continually flash while in peak mode.
While in “peak mode” the display will only display the highest value seen, lower
value will not be displayed.
Simply press [F3] again and the flashing will stop and the display will return to real
time measurements.
Warning
Reverting to real time from peak will result in loss of peak pressure reading. Record
the peak value prior to returning to normal real time reading.
UniMano 1000 Series 11

2.5 SET OPERATION
Press set from main menu
000.0 KP
A
unt
zro
peak
set
The following display will appear:
Setup Menu
Leak Alrm
2.5.1 LEAK DETECTION
The UniMano 1000 is capable of calculating the change in pressure over a
selected period of time.
Press [F1] Leak to select Leak Detection and the following menu appears:
Leak in Seconds
15 30
45 60
Use the [F] keys to determine the time span for the period of time you wish to
measurement to occur. Time intervals are in 15 second durations up to a
minute.
Once selected the display will revert back to the main display.
At the end of the selected measuring period the UniMano will beep and flash
the change in pressure value (5) five times and then the value freezes on the
display.
1.00 PSI
15 Seconds leak
In the above example the UniMano detected a 1 PSI leak over 15 second
period, on negative sign in front would indicate a increase in pressure of 1 PSI
over the same 15 Second interval, see below.
-1.00 PSI
15 Seconds leak
UniMano 1000 Series 12

2.5.2 Alarm Mode
The UniMano has an audio beeper that always activate during a overpressure
situation, for low battery situation and after Leak Detection. If you press [F2]
in the Setup Menu and select ‘ON’ [F1] the UniMano will also beep when
zeroing the unit and if Peak Function is selected. Pressing ‘OFF’ [F2] will
deactivate these two alarms. The UniMano will default on initiation to the
‘OFF’ position.
Beeper OFF
ON OFF
2.6 SIMPLE TROUBLESHOOTING GUIDE
When inaccurate pressure vacuum readings are suspected, check the following items:
Install a fresh 9 Volt battery.
Insure the display reads zero with no pressure applied to the instrument.
Auto zero if necessary.
Apply a known pressure, and verify the reading within the specifications of the
UniMano 1000 model, 0.1% Full Scale
2.7 TYPICAL APPLICATION SET UP
UniMano 1000 Series 13

TEST AND CALIBRATION SECTION 4
3.1 FACTORY CALIBRATION
The UniMano 1000 Series Pressure Vacuum Meter is shipped from the factory fully
calibrated with a Certificate of Calibration traceable to the NIST. Annual calibration is
recommended. Contact the Customer Service Department for instructions for returning the
instrument to Netech for either calibration or repair.
Extended Warranty Option:
If the instrument is returned to Netech Technical Service for its recommended annual
calibration, the standard one year warranty is extended for a second year.
Before attempting calibration please be aware that the warranty on the UniMano 1000
Series Pressure Vacuum Meter will become void if the Quality Seal is broken without
proper factory authorization.
UniMano 1000 Series 14

Appendix A
UniMano 1000 Series 15