NETGEAR XM128S User manual

M1-XM128S-1
March 1998
NETGEAR, Inc.
A Bay Networks Company
4401 Great America Parkway
Santa Clara, CA 95054 USA
Phone 888-NETGEAR
Getting Started Using
FirstGear for the Model
XM128S ISDN Digital
Modem
XM128S_bk.fm.book Page i Friday, March 6, 1998 11:33 AM

ii
© 1998 by NETGEAR, Inc. All rights reserved.
Trademarks
Bay Networks is a registered trademark of Bay Networks, Inc.
NETGEAR and FirstGear are trademarks of Bay Networks, Inc.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation.
Other brand and product names are trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Customer Support
For assistance with installing and configuring your NETGEAR system or with post-installation questions or problems,
contact your point of purchase representative.
To contact customer support or to purchase additional copies of this document and publications for other NETGEAR
products, you can contact NETGEAR at the following numbers:
• Phone:
U.S./Canada:1-800-211-2069
United Kingdom: (44) 171-571-5120
France: 0800-90-2078
Germany: 0130-817305
Australia: 800-14-20-46
New Zealand: 800-444-626
Korea: 00308-11-0319
•Fax:
U.S./Canada: 510-498-2609
World Wide Web
NETGEAR maintains a World Wide Web Home Page that you can access at the universal resource locator (URL)
http://NETGEAR.baynetworks.com. A direct connection to the Internet and a Web browser such as Internet Explorer
or Netscape are required.
Bulletin Board Service
NETGEAR maintains a bulletin board that you can access to obtain the latest version of the software. In the United
States, phone [phone].
XM128S_bk.fm.book Page ii Friday, March 6, 1998 11:33 AM

Contents iii
Contents
Preface
Purpose ............................................................................................................................vii
Conventions .....................................................................................................................viii
Special Message Formats .........................................................................................viii
Use of Enter, Type, and Press ...................................................................................viii
Other Conventions ..................................................................................................... ix
Related Publication........................................................................................................... ix
Chapter 1
Introduction
Features ..........................................................................................................................1-1
Chapter 2
Physical Description
Front Panel .....................................................................................................................2-1
LEDs ........................................................................................................................2-2
Rear Panel ......................................................................................................................2-3
Chapter 3
Installation
Package Contents ..........................................................................................................3-1
Installing the Modem ......................................................................................................3-2
Verifying Hardware Installation .......................................................................................3-3
Installing Software for Windows ......................................................................................3-3
Installing the Windows 95 Driver ..............................................................................3-4
Installing and Launching FirstGear .................................................................................3-6
Using the Advanced Feature for Setting Telephone Numbers .................................3-9
Configuring Windows 95 Dial-Up Networking ........................................................3-11
Configuring Dial-Up Networking for One B Channel ........................................3-11
Configuring Dial-Up Networking for Two B Channels ......................................3-16
Index
XM128S_bk.fm.book Page iii Friday, March 6, 1998 11:33 AM

iv Contents
XM128S_bk.fm.book Page iv Friday, March 6, 1998 11:33 AM

Figures v
Figures
Figure 2-1. Front panel of the Model XM128S modem (with S/T interface) ...............2-1
Figure 2-2. Rear panel of the Model XM128S modem ...............................................2-3
Figure 3-1. Model XM128S modem connections .......................................................3-2
Figure 3-2. New Hardware Found screen ..................................................................3-4
Figure 3-3. Install From Disk screen ...........................................................................3-5
Figure 3-4. Select Device screen ...............................................................................3-5
Figure 3-5. Welcome screen ......................................................................................3-7
Figure 3-6. FirstGear screen ......................................................................................3-8
Figure 3-7. Multiple Subscriber Numbers screen....................................................... 3-9
Figure 3-8. Outgoing Telephone Numbers screen ....................................................3-10
Figure 3-9. Make New Connection screen ...............................................................3-11
Figure 3-10. Make New Connection screen for entering ISP information ..................3-12
Figure 3-11. My Connection screen ...........................................................................3-13
Figure 3-12. Server Types tab screen ........................................................................3-14
Figure 3-13. TCP/IP Settings screen ..........................................................................3-15
XM128S_bk.fm.book Page v Friday, March 6, 1998 11:33 AM

vi Tables
Tables
Table 2-1. LED descriptions ......................................................................................2-2
Table 2-2. Rear panel components ...........................................................................2-3
XM128S_bk.fm.book Page vi Friday, March 6, 1998 11:33 AM

Preface vii
Preface
Congratulations on your purchase of the NETGEAR™Model XM128S ISDN Digital Modem. The
Model XM128S modem sets a new price and performance standard for rapidly growing Internet
and telecommuting applications.
The NETGEAR Model XM128S modem provides connection for one or more PCs to the Internet
or to the office over ISDN (Integrated Services Digital Network) lines. The modem operates at a
speed of up to 460 kilobits per second (Kbps) data rate, or 128 Kbps data rate without
compression, and can download video clips, music, or high-resolution color graphics from the
World Wide Web or other online services many times faster than an analog modem. The
Model XM128S modem supports concurrent data and voice communications, reducing cost and
administration of multiple phone lines.
Purpose
This guide provides instructions for the installation and use of the Model XM128S modem. This
guide also provides instructions in the installation and use of the FirstGear™configuration software
application for installing, configuring, and monitoring the Model XM128S modem.
XM128S_bk.fm.book Page vii Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
viii Preface
Conventions
This section describes the conventions used in this guide.
Special Message Formats
This guide uses the following formats to highlight special messages.
Use of Enter, Type, and Press
This guide uses “enter,” “type,” and “press” to describe the following actions:
• When you read “enter,” type the text and press the Enter key.
• When you read “type,” type the text, but do not press the Enter key.
• When you read “press,” press only the alphanumeric or named key.
• When you read “click,” click the left mouse button.
Note: This format is used to highlight information of importance or special interest.
Caution: This format is used to highlight information that will help you prevent
equipment failure or loss of data.
Warning: This format is used to highlight material involving possibility of injury or
equipment damage.
XM128S_bk.fm.book Page viii Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
Preface ix
Other Conventions
This guide uses the following additional conventions:
italics Book titles and UNIX file, command, and directory names.
Initial Caps Menu titles and window and button names.
Related Publication
For more information about the Model XM128S modem, refer to the Reference Guide for the
Model XM128 ISDN Digital Modem.
XM128S_bk.fm.book Page ix Friday, March 6, 1998 11:33 AM

XM128S_bk.fm.book Page x Friday, March 6, 1998 11:33 AM

Introduction 1-1
Chapter 1
Introduction
This guide describes how to install and use the Model XM128S ISDN Digital Modem. It includes
a physical description and installation instructions for the hardware, as well as instructions for
installing and using FirstGear to configure the modem. Use this guide as a reference for getting
started. For more detailed information about installing your Model XM128S modem, refer to
Reference Guide for the Model XM128 ISDN Digital Modem.
When used with off-the-shelf Internet or remote access client software, the Model XM128S
modem enables mobile or home users to connect over Integrated Services Digital Network (ISDN)
lines to the Internet or to branch offices. The Model XM128S modem also allows a user to connect
to the analog world through a modem, fax machine, or telephone.
To take advantage of constant new developments while sustaining your hardware investment, the
Model XM128S modem uses flash EPROMs that enable convenient uploading of newly available
firmware.
Features
The Model XM128S ISDN Digital Modem supports a variety of compression schemes including
V.42bis and Hi/fn LZS Compression (Stac). This modem can effectively communicate at speeds up
to 460 kilobits per second (Kbps) over ISDN lines.
The Model XM128S modem has two analog ports to connect analog devices such as fax machines,
modems, and telephones. The Model XM128S modem can communicate over the two B channels
to different locations simultaneously, enabling you to send a fax and “surf” the web at the same
time. The analog ports recognize standard dual-tone multifrequency (DTMF) tones as well as
pulse dialing.
XM128S_bk.fm.book Page 1 Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
1-2 Introduction
The Model XM128S modem has the following speed and compatibility features:
• Plug-and-Play support for a Windows®95 environment
• Full compatibility with both ISDN and remote public-switched telephone network (PSTN)
by way of ISDN
• Multiple signaling protocol compatibility with DSS1, 1TR6, NI-1, AT&T 5ESS, and Northern
Telecom DMS 100 network switches
• X.75, V.110, V.120, and Point-to-Point Protocol (PPP)
• B channel speeds of 56 Kbps (in-band signaling) and 64 Kbps (out-of-band signaling)
• 112 Kbps/128 Kbps channel bundling: MLP and Multipoint PPP (RFC1717)
• Hi/fn LZS compression (Stac)
• V.42bis data compression using the X.75, V.120, and bundle protocols
• Configurable using either FirstGear (a Windows 95 utility) or AT commands
• Automatic ISDN and analog call detection
• Two analog telephone jacks (analog adapters)
• Push-button switch for quick dial and teardown
• Easy-to-use FirstGear configuration software
• Flash EPROM for easy firmware upgrades
XM128S_bk.fm.book Page 2 Friday, March 6, 1998 11:33 AM

Physical Description 2-1
Chapter 2
Physical Description
This chapter provides information about the hardware features of the Model XM128S ISDN
Digital Modem. Use the key at the bottom of each illustration to identify the panel components.
Front Panel
For easier management and control of the Model XM128S modem, familiarize yourself with the
components on the front panel, as illustrated in Figure 2-1.
Key:
1 = PWR (power) LED
2 = ISDN LEDs
3 = RS-232 COM LEDs
4 = PHONE 1 and PHONE 2 LEDs
Figure 2-1. Front panel of the Model XM128S modem (with S/T interface)
7848MEA
DTR DSR RTS CTS TDDPWR B1 B2 AA CP
ISDN RD 12
ISDN Digital Modem
INTERFACE
128Kpbs MODELXM128
S
COM
2 3 4
1
XM128S_bk.fm.book Page 1 Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
2-2 Physical Description
LEDs
LEDs on the front panel of the Model XM128S modem allow you to monitor and diagnose the
device. Table 2-1 describes each LED.
Table 2-1. LED descriptions
Label Color Activity Description
PWR
(power) Green On Power is supplied to the modem.
ISDN LEDs:
D Green On The ISDN link on the D channel is active.
Blinking The Model XM128S modem is attempting to make a connection
to the switch.
B1 Green On A connection is established to the B1 channel.
B2 Green On A connection is established to the B2 channel.
AA Green On The Model XM128S modem is in the automatic answering mode.
Blinking An incoming call is ringing.
CP Green On Compression is active on either of the B channels.
RS-232
COM LEDs:
DTR Green On The data terminal or computer connected to the DTE port on
the Model XM128S modem is ready to communicate.
DSR Green On The Model XM128S modem is ready to communicate with the
connected data terminal or computer.
RTS Green On The data terminal or computer connected to the DTE port on
the Model XM128S modem is ready to transmit data.
CTS Green On The Model XM128S modem is ready to accept data from the
connected data terminal or computer.
TD Green On The data terminal or computer connected to the Model XM128S
modem is transmitting data to the modem.
RD Green On The data terminal or computer connected to the Model XM128S
modem is receiving data from the DTE port of the modem.
PHONE 1 Green On The telephone connected to the port is in use.
PHONE 2 Green On The telephone connected to the port is in use.
XM128S_bk.fm.book Page 2 Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
Physical Description 2-3
Rear Panel
The rear panel (Figure 2-2) contains a power switch; a power receptacle; and ports to connect a
computer, an ISDN line, and two analog devices (telephone, fax, or modem).
Key:
1 = ON/OFF switch
2 = Receptacle for power adapter
3 = RS-232 communication (COM) port for connecting to a computer
4 = ISDN-S port for connecting to an ISDN line
5 = PHONE 1 and PHONE 2 ports for connecting analog devices (telephone, fax, or modem)
Figure 2-2. Rear panel of the Model XM128S modem
Table 2-2 describes the components on the rear panel of the Model XM128S modem.
Table 2-2. Rear panel components
Label Description
ON/OFF This switch turns power on or off.
POWER This receptacle is for the power adapter.
RS-232 This RS-232 COM port is for connecting the Model XM128S modem to the serial port of a
computer or data terminal.
ISDN-S This port is for connecting the Model XM128S modem to the NT1 device.
PHONE 1 This port is for connecting the Model XM128S modem to an analog device (telephone,
fax, or modem).
PHONE 2 This port is for connecting the Model XM128S modem to an analog device (telephone,
fax, or modem).
7861MEA
RS-232
POWER
ON/OFF
1 2 3
ISDN-S PHONE 1PHONE 2
5
4
XM128S_bk.fm.book Page 3 Friday, March 6, 1998 11:33 AM

XM128S_bk.fm.book Page 4 Friday, March 6, 1998 11:33 AM

Installation 3-1
Chapter 3
Installation
This chapter provides information about installing and using the Model XM128S ISDN Digital
Modem.
Package Contents
Your package should contain the following items:
• Model XM128S ISDN Digital Modem
• Power adapter
• RJ-45 ISDN telephone cable
• Shielded RS-232 25-pin straight cable
• 25-pin to 9-pin adapter
• This manual
• Reference Guide for the Model XM128 ISDN Digital Modem
• CD ROM with bundled software
• 3.5-inch driver and utility diskettes
• Warranty and Owner Registration Card
Call your reseller or customer support in your area if there are any wrong, missing, or damaged
parts. Refer to page ii for the location of customer support in your area.
Keep the carton, including the original packing materials. Use them to repack the modem if you
need to return it for repair.
To qualify for product updates and product warranty registrations, fill in the Warranty and Owner
Registration Card within 30 days of purchase and return it to NETGEAR, Inc.
XM128S_bk.fm.book Page 1 Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
3-2 Installation
Installing the Modem
Before connecting any of the devices to your modem, make sure the power is turned off on your
computer and your Model XM128S modem. To connect the ISDN line to your modem, you must
use an NT1 device (usually supplied by the telephone company), which converts the S/T interface
of the Model XM128S modem to a U interface. Refer to Figure 3-1 and then to the steps following
the illustration for detailed instructions for making those connections.
Key:
1 = Model XM128S modem
2 = AC power adapter
3 = Computer (PC, Macintosh, or UNIX workstation)
4 = Shielded RS-232 25-pin straight cable
5 = ISDN connection to NT1 device (connected with ISDN cable provided in package)
6 = Analog device (telephone, fax, or modem)
Figure 3-1. Model XM128S modem connections
To install your Model XM128S modem:
1. Connect the male end of the 25-pin straight cable to the RS-232 COM port of the
Model XM128S modem.
7860MEA
1
6
2
3
4 5
6
XM128S_bk.fm.book Page 2 Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
Installation 3-3
2. Connect the other end (female end) of the 25-pin straight cable to the serial (COM) port
on your computer.
3. Using the ISDN cable that is included, connect the RJ-45 connector on one end of the
cable to the ISDN-S port on the back of the Model XM128S modem.
4. Connect the other end of the ISDN cable to the S/T interface on your NT1 device.
5. Using the proper cable, connect the NT1 device to the wall outlet installed by your phone
company.
6. Insert the round end of the power adapter in the POWER connector on the rear panel.
7. Plug the power adapter into an AC wall outlet.
8. Turn the power on to your Model XM128S modem.
9. Turn the power on to your computer.
Verifying Hardware Installation
When the installation is complete and power applied to the modem, a self-test sequence begins.
The B1, B2, and AA LED lights blink on and then off again. After this cycle is complete, the PWR
(power) LED remains on.
If the test routine fails, the D LED blinks. Refer to Reference Guide for the Model XM128 ISDN
Digital Modem for more information about the self-test and the error codes.
Installing Software for Windows
This section contains information about installing the Windows 95 and Windows NT®drivers and
about configuring Dial-Up Networking.
Note: If your computer has a 9-pin serial connector, use a 25-pin to 9-pin converter
(25-pin male to 9-pin female). If you have a Macintosh, a special cable is needed for the
connection.
XM128S_bk.fm.book Page 3 Friday, March 6, 1998 11:33 AM

Getting Started Using FirstGear for the Model XM128S ISDN Digital Modem
3-4 Installation
Installing the Windows 95 Driver
The Model XM128S modem is Plug-and-Play compatible with Windows 95. If you are running
Windows 95 or Windows NT, refer to this section to install the Windows 95 driver. If you are
running Windows 3.X, refer to Chapter 4, “Configuration,” in the Reference Guide for the Model
XM128 ISDN Digital Modem for information about using a terminal program and AT commands
for configuring your modem.
To install the Windows 95 driver:
1. Turn on power to your Model XM128S modem.
2. Turn on power to your PC, and start Windows 95.
The New Hardware Found screen opens, as illustrated in Figure 3-2. Windows 95 detects your
Model XM128S modem automatically and prompts you to indicate which driver you want to
install for your new hardware.
Figure 3-2. New Hardware Found screen
3. Click on the Driver from disk provided by hardware manufacturer field.
XM128S_bk.fm.book Page 4 Friday, March 6, 1998 11:33 AM