NETGEAR Wireless-N 150 User manual

202-10523-01
January 2010
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134
Wireless-N 150 ADSL2+
Modem Router DGN1000
User Manual

ii
v1.1, January 2010
©2010 by NETGEAR, Inc. All rights reserved..
Technical Support
Please refer to the support information card that shipped with your product. By registering your product at
http://www.netgear.com/register, we can provide you with faster expert technical support and timely notices of product
and software upgrades.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card.
E-mail: [email protected]
North American NETGEAR website: http://www.netgear.com
Trademarks
NETGEAR, the NETGEAR logo, ProSafe, Smart Wizard, and Auto Uplink are trademarks or registered trademarks of
NETGEAR, Inc. Microsoft, Windows, Windows NT and Vista are registered trademarks of Microsoft Corporation.Other
brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Wireless-N 150 ADSL2+ Modem Router has been suppressed in accordance with the
conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example,
test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions.
The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and
has been granted the right to test the series for compliance with the regulations.
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß dasWireless-N 150 ADSL2+ Modem Router gemäß der im BMPT-AmtsblVfg 243/1991
und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B.
Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der
Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the Class B category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used
near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.

v1.1, January 2010
iii
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result
in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country.
Therefore, all options described in this user's guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the
European Union (1999/5/EC). This equipment meets the following conformance standards:
EN300 328, EN301 489-17, EN60950
Europe – Declaration of Conformity in Languages of the European Community
Cesky [Czech] NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními
požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES..
Dansk
[Danish]
Undertegnede NETGEAR Inc. erklærer herved, at følgende udstyr Radiolan overholder
de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt NETGEAR Inc., dass sich das Gerät Radiolan in Übereinstimmung mit
den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der
Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab NETGEAR Inc. seadme Radiolan vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, NETGEAR Inc., declares that this Radiolan is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR Inc. ΔΗΛΩΝΕΙ ΟΤΙ Radiolan ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente NETGEAR Inc. déclare que l'appareil Radiolan est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian] Con la presente NETGEAR Inc. dichiara che questo Radiolan è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo NETGEAR Inc. deklarē, ka Radiolan atbilst Direktīvas 1999/5/EK būtiskajām
prasībām un citiem ar to saistītajiem noteikumiem.

v1.1, January 2010
iv
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only. Any
product changes or modifications will invalidate all applicable regulatory certifications and approvals
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Lietuvių
[Lithuanian]
Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese] Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonforma mal-htigijiet
essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish] Niniejszym NETGEAR Inc. oświadcza, że Radiolan jest zgodny z zasadniczymi
wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese] NETGEAR Inc. declara que este Radiolan está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak] NETGEAR Inc. týmto vyhlasuje, že Radiolan spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish] NETGEAR Inc. vakuuttaa täten että Radiolan tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Íslenska
[Icelandic]
Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og aðrar
kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Norsk
[Norwegian] NETGEAR Inc. erklærer herved at utstyret Radiolan er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

v1.1, January 2010
v
FCC Declaration Of Conformity
We NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the model
DGN1000 Wireless-N 150 ADSL2+ Modem Router complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following methods:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
PY306100037
Wireless-N 150 ADSL2+ Modem Router
Modifications made to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to operate
the equipment.
Product and Publication Details
Model Number: DGN1000
Publication Date: January 2010
Product Family: Wireless Modem Router
Product Name: Wireless-N 150 ADSL2+ Modem Router
Home or Business Product: Home
Language: English
Publication Part Number: 202-10523-01
Publication Version Number: 1.1

vi
v1.1, January 2010
Contents
Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
About This Manual
Conventions, Formats, and Scope ................................................................................... xi
Revision History ............................................................................................................... xii
Chapter 1
Connecting Your Wireless Modem Router to the Internet
Using the Setup Manual .................................................................................................1-1
What You Need before You Begin .................................................................................1-2
Logging In to the Wireless Modem Router .....................................................................1-2
Using the Setup Wizard ..................................................................................................1-4
Auto-Detecting Your Internet Connection .......................................................................1-5
Viewing or Manually Configuring Your ISP Settings .......................................................1-6
Understanding the Basic Settings Screen ......................................................................1-8
Configuring ADSL Settings ...........................................................................................1-10
How the Internet Connection Works .............................................................................1-11
Chapter 2
Configuring Your Wireless Network
and Security Settings
Planning Your Wireless Network ....................................................................................2-1
Wireless Placement and Range Guidelines .............................................................2-2
Wireless Security Options ........................................................................................2-3
Manually Configuring Your Wireless Network ................................................................2-4
Manually Configuring Your Wireless Security ................................................................2-7
Restricting Wireless Access to Your Network ..........................................................2-8
Configuring Mixed WPA-PSK+WPA2-PSK Security ..............................................2-10
Choosing Alternative Authentication and Encryption Methods ..............................2-11
Using Push 'N' Connect (WPS) to Configure Your Wireless Network and Security .....2-13
Connecting Additional Wireless Client Devices After WPS Setup .........................2-16

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
vii
v1.1, January 2010
Chapter 3
Protecting Your Network
Changing the Built-In Password .....................................................................................3-1
Changing the Administrator Login Time-out .............................................................3-2
Blocking Keywords, Sites, and Services ........................................................................3-2
Firewall Rules .................................................................................................................3-4
Configuring Firewall Rules .......................................................................................3-5
Inbound Rules (Port Forwarding) .............................................................................3-5
Outbound Rules (Service Blocking) .........................................................................3-8
Order of Precedence for Rules ................................................................................3-9
Services ........................................................................................................................3-10
Setting Times and Scheduling Firewall Services ..........................................................3-12
Setting Your Time Zone .........................................................................................3-12
Scheduling Firewall Services .................................................................................3-13
Enabling Security Event E-mail Notification .................................................................3-14
Chapter 4
Managing Your Network
Updating the Firmware ...................................................................................................4-1
Manually Checking for Firmware Updates ...............................................................4-2
Backing Up, Restoring, and Erasing Your Settings ........................................................4-3
Backing Up the Configuration to a File .....................................................................4-4
Restoring the Configuration from a File ...................................................................4-4
Erasing the Configuration .........................................................................................4-4
Viewing the Wireless Modem Router Status ..................................................................4-5
Showing Statistics ....................................................................................................4-7
Showing the Connection Status ...............................................................................4-8
Viewing Attached Devices ..............................................................................................4-9
Running Diagnostic Utilities and Rebooting the Wireless Modem Router ....................4-10
Configuring Remote Management ................................................................................4-11
Chapter 5
Advanced Configuration
Configuring WAN Settings ..............................................................................................5-1
Setting Up a Default DMZ Server .............................................................................5-3
Configuring Dynamic DNS ..............................................................................................5-4
Configuring LAN Setup ...................................................................................................5-6

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
viii
v1.1, January 2010
Configuring DHCP ....................................................................................................5-8
Configuring Reserved IP Addresses ........................................................................5-9
Configuring Dynamic DNS .......................................................................................5-9
Configuring Advanced Wireless Settings .....................................................................5-11
Using Static Routes ......................................................................................................5-13
Static Route Example .............................................................................................5-13
Configuring Static Routes ......................................................................................5-14
Configuring Universal Plug and Play ............................................................................5-15
Chapter 6
Troubleshooting
Basic Functioning ...........................................................................................................6-1
“Welcome” Page Displays instead of Router Main Menu .........................................6-2
Power LED Is Off .....................................................................................................6-2
Power LED Is Red ....................................................................................................6-2
LAN or ADSL Port LED Is Off ..................................................................................6-3
Window Appears Asking You to Reload Firmware ..................................................6-3
Cannot Log in to the Wireless Modem Router ................................................................6-3
Troubleshooting the ISP Connection ..............................................................................6-4
ADSL Link ................................................................................................................6-4
Internet LED is Red ..................................................................................................6-5
Obtaining an Internet IP Address .............................................................................6-5
Troubleshooting PPPoE or PPPoA ..........................................................................6-6
Troubleshooting Internet Browsing ..........................................................................6-7
Resolving a ‘Reload Firmware’ Message .................................................................6-7
Automatic Firmware Recovery .......................................................................................6-8
Troubleshooting a TCP/IP Network Using the Ping Utility ..............................................6-9
Testing the LAN Path to Your Wireless Modem Router ...........................................6-9
Testing the Path from Your Computer to a Remote Device ...................................6-10
Problems with Date and Time ......................................................................................6-10
Appendix A
Factory Settings, Technical Specifications, and Wall Mounting
Factory Settings ............................................................................................................. A-1
Technical Specifications ................................................................................................ A-2
Wall-Mounting Your Modem Router .............................................................................. A-3

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
ix
v1.1, January 2010
Appendix B
Related Documents
Index

x
v1.1, January 2010
About This Manual
The NETGEAR®Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual describes how
to install, configure and troubleshoot the Wireless-N 150 ADSL2+ Modem Router. The
information in this manual is intended for readers with intermediate computer and Internet skills.
Conventions, Formats, and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•Typographical Conventions.This manual uses the following typographical conventions:
Italic Emphasis, books, CDs
Bold User input, IP addresses, GUI screen text
Fixed Command prompt, CLI text, code
italic URL links
•Formats.This manual uses the following formats to highlight special messages:
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note may result in a malfunction or damage to the
equipment.
Note: This format is used to highlight information of importance or special interest.

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
xi
v1.1, January 2010
•Scope.This manual is written for the Modem Router according to these specifications:
Product Version Wireless-N 150 ADSL2+ Modem Router
Manual Publication Date January 2010
For more information about network, Internet, firewall, and VPN technologies, see the links to the
NETGEAR website in Appendix B, “Related Documents.”
Note: Product updates are available on the NETGEAR, Inc. website at
http://kbserver.netgear.com/products/DGN1000.asp.
Revision History
Part Number Version
Number Date Description
202-10523-01 1.0 October
2009
Original publication.
202-10523-01 1.1 January
2010
Wireless mode setting was changed from 130 to 150. Wall-
mounting instructions were added to Appendix A.

1-1
v1.1, January 2010
Chapter 1
Connecting Your Wireless Modem Router to the
Internet
This chapter describes how to configure your Wireless-N 150 ADSL2+ Modem Router Internet
connection. When you perform the initial configuration of your wireless modem router using the
Resource CD as described in the Wireless Modem Router DGN1000 Setup Manual, these settings
are configured automatically for you. This chapter provides further details about these settings, as
well as instructions on how to log in to the wireless modem router for further configuration.
Note: NETGEAR recommends using the Smart Wizard on the Resource CD for initial
configuration, as described in the
Wireless Modem Router DGN1000 Setup Manual.
This chapter includes:
•“Using the Setup Manual”
•“What You Need before You Begin” on page 1-2”
•“Logging In to the Wireless Modem Router” on page 1-2”
•“Auto-Detecting Your Internet Connection” on page 1-5”
•“Viewing or Manually Configuring Your ISP Settings” on page 1-6”
•“Configuring ADSL Settings” on page 1-10”
•“How the Internet Connection Works” on page 1-11”
Using the Setup Manual
For first-time installation of your modem router, refer to the Wireless Modem Router DGN1000
Setup Manual. The Setup Manual explains how to launch the NETGEAR Smart Wizard on the
Resource CD to step you through the procedure to connect your router, modem, and computers.
The Smart Wizard will assist you in configuring your wireless settings and enabling wireless
security for your network. After initial configuration using the Setup Manual, you can use the
information in this Reference Manual to configure additional features of your wireless router.

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
1-2 Connecting Your Wireless Modem Router to the Internet
v1.1, January 2010
For installation instructions in a language other than English, see the language options on the
Resource CD.
What You Need before You Begin
You need to prepare the following before you can set up your wireless modem router:
• Active Internet service provided by an ADSL account
• The Internet Service Provider (ISP) configuration information for your ADSL account
– ISP login name and password
– ISP Domain Name Server (DNS) addresses
– Fixed or static IP address
– Host and domain names
• Depending on how your ISP set up your Internet account, you need to know one or more of
these settings:
– Virtual path identifier (VPI) and Virtual channel identifier (VCI) parameters
– Multiplexing method
– Host and domain names
• ASDL microfilters as explained in the Wireless Modem Router DGN1000 Setup Manual
In addition, your computer must be set up to use DHCP to get its TCP/IP configuration from the
modem router. This is usually the case. For help with DHCP, see the documentation that came with
your computer, or see the link to the online document that you can access from Appendix B,
“Related Documents.
Your ISP should have provided you with all the information needed to connect to the Internet. If
you cannot locate this information, you can ask your ISP to provide it.
Logging In to the Wireless Modem Router
You can log in to the wireless modem router to view or change its settings.
Note:Your computer must be configured for DHCP. For help with configuring DHCP, see
the documentation that came with your computer or see the link to the online docu-
ment that you can access from “Preparing a Computer for Network Access” in
Appendix B.

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
Connecting Your Wireless Modem Router to the Internet 1-3
v1.1, January 2010
To log in to the wireless modem router:
1. Type http://192.168.0.1 in the address field of your browser, and then click Enter. A login
window will display.
.
Figure 1-1
2. Enter admin:for the user name and password for the password, both in lower case letters.
If the wireless modem router has never been configured, the Smart Wizard screen displays.
After the wireless modem router has been configured, the Firmware Upgrade assistant will
appear.
•Checking for Firmware Updates screen. After initial configuration, this screen displays
unless you previously cleared the Check for Updated Firmware Upon Log-in check box.
Figure 1-2
If the wireless modem router discovers a newer version of the firmware, you are asked if you
want to upgrade to the new firmware (see “Updating the Firmware” on page 4-1for details). If
no new firmware is available, the following message displays.

Figure 1-3
Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
1-4 Connecting Your Wireless Modem Router to the Internet
v1.1, January 2010
•Router Status screen. The Router Status screen displays if the wireless modem router has not
been configured yet or has been reset to its factory default settings. See “Viewing the Wireless
Modem Router Status” on page 4-5.
You can use the Setup Wizard to automatically detect your Internet connection as described in
“Using the Setup Wizard, or you can bypass the Setup Wizard and manually configure your
Internet connection as described in “Viewing or Manually Configuring Your ISP Settings” on
page 1-6.
Using the Setup Wizard
You can manually configure your Internet connection using the Basic Settings screen, or you can
allow the Setup Wizard to detect your Internet connection. The Setup Wizard searches your
Internet connection for servers and protocols to determine your ISP configuration. This feature is
not the same as the Smart Wizard on the Resource CD that is used for installation.
To use the Setup Wizard:
1. To go to the Setup Wizard screen, from the top of the main menu, select Setup Wizard:
Figure 1-4

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
Connecting Your Wireless Modem Router to the Internet 1-5
v1.1, January 2010
2. Select your country and language:
•Country. It is important to specify the location where the wireless modem router will
operate so that the Internet connection will work correctly.
•Language. You can select a language from the drop-down list.
3. If you want to change the settings for the Internet connection, select Yes or No.
–Yes. Let the wireless modem router Setup Wizard auto-detect the type of Internet
connection that you have and configure it. See the next section, “Auto-Detecting Your
Internet Connection.”
–No, I want to Configure the Router Myself. Enter your Internet settings manually in
the Basic Settings screen. See “Understanding the Basic Settings Screen” on page 1-8.
In either case, use the configuration settings that your ISP provided to assure that the
configuration for your Internet connection is correct.
4. Click Next.
Auto-Detecting Your Internet Connection
The Smart Setup Wizard searches your Internet connection for servers and protocols to determine
your ISP configuration.
Note: The wizard cannot detect a PPTP connection with your ISP. If your ISP uses this
protocol, then you must configure your connection manually (see “Understanding
the Basic Settings Screen” on page 1-8).
To use the Smart Setup Wizard to assist with configuration or to view the Internet connection
settings:
1. From the Setup Wizard screen, select Yes for the Auto-Detect Connection Type, and then click
Next to proceed.
The Setup Wizard detects your ISP configuration. Depending on the type of connection, you
are prompted to enter your ISP settings, as shown in the following table.
Table 1-1. Auto-Detected Internet Connection Types
Connection Type ISP Information
PPP over Ethernet (PPPoE)
PPP over ATM (PPPoA)
Enter the login user name and password. These fields are case-
sensitive.

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
1-6 Connecting Your Wireless Modem Router to the Internet
v1.1, January 2010
2. To save your settings, click Apply.
Viewing or Manually Configuring Your ISP Settings
NETGEAR recommends that you specify your country and language before you configure the
settings on the Basic Settings screen. See “Logging In to the Wireless Modem Router” on
page 1-2. You must install the ADSL filters and connect the wireless modem router to the ADSL
line as described in the Wireless Modem Router DGN1000 Setup Manual before you configure the
settings in the Basic Settings screen.
Dynamic IP Account Setup No entries needed.
IP over ATM Classical IP
assignment (RFC1577)
• Enter the assigned IP address, subnet mask, and the IP address
of your ISP’s primary DNS server. If a secondary DNS server
address is available, enter it also.
• DNS servers are required to perform the function of translating
an Internet name such as www.netgear.com to a numeric IP
address. For a fixed IP address configuration, you must obtain
DNS server addresses from your ISP and enter them manually
here.
Fixed IP (Static) Account Setup 1. If required, enter the account name and domain name from
your ISP.
2. Select Use Static IP Address or Use IP Over ATM (IPoA —
RFC1483 Routed) according to the information from your ISP.
If you select IPoA, the router will detect the gateway IP
address, but you still need to provide the router IP address.
3. Enter your assigned IP address, subnet mask, and the IP
address of your ISP’s gateway wireless modem router. This
information should have been provided to you by your ISP.
4. Enter the IP address of your ISP’s primary DNS server. If a
secondary DNS server address is available, enter it also.
DNS servers are required to perform the function of translating
an Internet name such as www.netgear.com to a numeric IP
address. For a fixed IP address configuration, you must obtain
DNS server addresses from your ISP and enter them manually
here.
Table 1-1. Auto-Detected Internet Connection Types (continued)
Connection Type ISP Information

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
Connecting Your Wireless Modem Router to the Internet 1-7
v1.1, January 2010
To view or configure the basic settings:
1. Log in to the wireless modem router as described in “Logging In to the Wireless Modem
Router” on page 1-2.
2. Select Basic Settings to display the Basic Settings screen.
The Basic Settings screen is explained in “Understanding the Basic Settings Screen” on
page 1-8.
3. Select Yes or No depending on whether your ISP requires a login. This selection changes the
fields available on the Basic Settings screen.
•Yes. If your ISP requires a login, select the encapsulation method. Enter the login name. If
you want to change the login time-out, enter a new value in minutes.
•No. If your ISP does not require a login, enter the account name, if required, and the
domain name, if required.
4. Enter the settings for the IP address and DNS server.
The default ADSL settings usually work fine. If you have problems with your connection,
check the ADSL settings. See “Configuring ADSL Settings” on page 1-10 for more details.
5. If no login is required, you can specify the MAC Address setting.
6. Click Apply to save your settings.
7. Click Test to test your Internet connection. If the NETGEAR website does not appear within
one minute, refer to Chapter 6, “Troubleshooting.”
Note: When your Internet connection is working you will no longer need to launch the
ISP’s login program on your computer to access the Internet. When you start an
Internet application, your wireless modem router automatically logs you in.

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
1-8 Connecting Your Wireless Modem Router to the Internet
v1.1, January 2010
Understanding the Basic Settings Screen
The fields on the Basic Settings screen depend on whether or not your Internet connection requires
a login.
ISP does not require login ISP does require login
Figure 1-5
The following table explains the fields in the Basic Settings screen. Note that the group of
fields included in this screen depends on whether or not a login is required.

Wireless-N 150 ADSL2+ Modem Router DGN1000 User Manual
Connecting Your Wireless Modem Router to the Internet 1-9
v1.1, January 2010
Table 1-2. Basic Settings screen fields
Settings Description
Does Your ISP Require a Login? •Yes
•No
These fields
appear only if no
login is required.
Account Name
(If required)
Enter the account name provided by your ISP. This might also
be called the host name.
Domain Name
(If required)
Enter the domain name provided by your ISP.
These fields
appear only if
your ISP
requires a login.
Encapsulation • PPPoE (PPP over Ethernet)
• PPPoA (PPP over ATM)
Login The login name provided by your ISP. This is often an e-mail
address.
Password The password that you use to log in to your ISP.
Idle Timeout (In minutes) If you want to change the login time-out, enter a new value in
minutes. This determines how long the wireless modem router
keeps the Internet connection active after there is no Internet
activity from the LAN. Entering a value of 0 (zero) means
never log out.
Internet IP
Address
•Get Dynamically from ISP. Your ISP uses DHCP to assign
your IP address. Your ISP automatically assigns these
addresses.
•Use Static IP Address. Enter the IP address that your ISP
assigned. Also enter the IP subnet mask and the gateway IP
address. The gateway is the ISP’s wireless modem router to
which your wireless modem router will connect.
This field appears only if
no login is required.
•Use IP Over ATM (IPoA). Your ISP uses Classical IP
addresses (RFC 1577). Enter the IP address, IP subnet
mask, and gateway IP addresses that your ISP assigned.
Domain Name Server (DNS) Address The DNS server is used to look up site addresses based on
their names.
•Get Automatically from ISP. Your ISP uses DHCP to
assign your DNS servers. Your ISP automatically assigns
this address.
•Use These DNS Servers. If you know that your ISP does
not automatically transmit DNS addresses to the wireless
modem router during login, select this option, and enter the
IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.