NETGEAR XSM7224S - ProSafe 10 Gigabit Stackable Manual

350 East Plumeria Drive
San Jose, CA 95134
USA
November 2010
202-10751-01
v1.0
Managed Stackable Switch
XSM7224S
Hardware Installation Guide

2|
Managed Stackable Switch XSM7224S
© 2010 NETGEAR, Inc.© 2010 by NETGEAR, Inc. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form or by any means without the written permission of NETGEAR, Inc.
P/N: Part Number TBD v1.0
Technical Support
When you register your product at http://www.netgear.com/register, we can provide you with faster expert technical
support and timely notices of product and software upgrades.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
E-mail: [email protected]
Website: http://www.netgear.com
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card.
Trademarks
NETGEAR, the NETGEAR logo, ProSafe, Smart Wizard, and Auto Uplink are trademarks or registered
trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT, and Vista are registered trademarks of Microsoft
Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes
to the products described in this document without notice. NETGEAR does not assume any liability that may occur
due to the use or application of the product(s) or circuit layout(s) described herein.
Revision History
Publication Part Number Version Publish Date
202-10751-01 v1.0 November 2010

Table of Contents |3
Chapter 1 Introduction
XSM7224S Front Panel and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
XSM7224S Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2 Hardware Installation
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Protecting Against Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . 8
Unpacking the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Select a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Install the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Check the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connect to Power and Check the LEDs . . . . . . . . . . . . . . . . . . . . . . . . 11
Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing an Adapter and Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Creating a Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power Module Bay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing a Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Removing a Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting Equipment to the Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
RJ-45 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting a Console to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Chapter 3 Troubleshooting
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Additional Troubleshooting Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix A Technical Specifications
Specifications for XSM7224S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specifications for GSM7328S and GSM7352S . . . . . . . . . . . . . . . . . . . . . 23
Appendix B Default Configuration Settings
Appendix C Notification of Compliance
Table of Contents

4|Contents
Managed Stackable Switch XSM7224S

Chapter 1. Introduction |5
1
1. Introduction
The NETGEAR ProSafe 10Gigabit Managed L2+ Stackable Switch XSM7224S is a
state-of-the-art, high-performance, IEEE-compliant network solution. It includes powerful
management features that you can use to eliminate bottlenecks, boost performance, and
increase productivity.
This guide describes hardware installation and basic troubleshooting for the XSM7224S Switch
This switch can be free-standing, or rack-mounted in a wiring closet or an equipment room. For
information about features for each product, see the NETGEAR website at
http://www.netgear.com.
XSM7224S Front Panel and LEDs
The following figure shows the front panel of the XSM7224S. The front panel contains LEDs,
a Reset button, a USB port, copper/fiber combo ports, and 10G SFP+ ports. The module
bays support any combination of ProSafe 10GBase-SR SFP+ Module AXM761, ProSafe
10GBase-LR SFP+ Module AXM762, or ProSafe 10GBase-LRM SFP+ Module AXM763.
See SFP+ Modules in Chapter 2.
Figure 1. XSM7224S Front Panel
LEDs
Reset button SFP+ Ports Combo Ports
USB Port
Console Port

6|Chapter 1. Introduction
Managed Stackable Switch XSM7224S
l
Table 1. LED Descriptions for XSM7224S
LED Description
ID This is the stack member ID (1–99) that the software assigns to the switch.
Stack Master • Green: The switch acts as a master unit in a stack of XSM7224S series
switches.
• Off: The switch acts as a slave unit in a stack of XSM7224S series switches.
Power • Solid green: The power module is present, is supplying power to the switch, and
is working normally.
• Solid yellow: The system is in boot-up stage.
• Blinking yellow: Power module is present but has failed.
• Off: Power is disconnected.
Fan • Solid green: The fan is operating normally.
• Solid yellow: The fan has failed.
• Off: No fan is detected.
10GBT Ports
(2 LEDs per port) 10/100M Link/ACT LED:
• Off: No 10/100M link is established on the port.
• Solid yellow: A valid 10/100M link is established on the port.
• Blinking yellow: The port is transmitting or receiving packets at 10/100Mbps.
Left side LED
1G/10G Link/ACT LED:
• Off: No 1G/10G link is established on the port.
• Solid Green – A valid 10Gbps link is established on the port.
• Blinking Green – Packet transmission or reception is occurring on the port at
10Gbps.
• Solid Yellow – A valid 1000Mbps link is established on the port.
• Blinking Yellow – Packet transmission or reception is occurring on the port at
1000Mbps.
Note: If port 21–24 media is changed to SFP+, the RJ-45 LEDs change to OFF
status.
SFP+ Ports
(1 SPD/Link/ACT
LED per port)
• Off: No SFP/SFP+ module link is established on the port.
• Solid green: A valid 10Gbps SFP+ module link is established on the port.
• Blinking green: The port is transmitting or receiving packets at 10Gbps.
• Solid yellow: A valid 1Gbps SFP module link is established on the port.
• Blinking yellow: Packet transmission or reception is occurring on the port at
1Gbps.
Note: If port 21–24 media is changed to copper, the SFP+ LEDs change to Off
status.
Right side LED

Chapter 1. Introduction |7
Managed Stackable Switch XSM7224S
XSM7224S Rear Panel
The rear panel has two fan trays, a power supply connector, a replaceable power supply, and
a bay for for an optional redundant power supply (APS300W).
Figure 2. XSM7224S Rear Panel
Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to help protect
your system from potential damage.
To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,
observe the following precautions.
• Observe and follow service markings.
- Do not service any product except as explained in your system documentation.
- Opening or removing covers that are marked with the triangular symbol with a
lightning bolt may expose you to electrical shock. Only a trained service
technician should service components inside these compartments.
• If any of the following conditions occur, unplug the product from the electrical outlet and
replace the part or contact your trained service provider:
- The power cable, extension cable, or plug is damaged.
- An object has fallen into the product.
- The product has been exposed to water.
- The product has been dropped or damaged.
- The product does not operate correctly when you follow the operating instructions.
• Keep your system away from radiators and heat sources. Also, do not block cooling
vents.
• Do not spill food or liquids on your system components, and never operate the product in
a wet environment. If the system gets wet, see the appropriate section in your
troubleshooting guide or contact your trained service provider.
• Do not push any objects into the openings of your system. Doing so can cause fire or
electric shock by shorting out interior components.
Replaceable
AC Power
Connector
Power Supply
Replaceable
Fan TraysSupply Bay
Optional Power

8|Chapter 1. Introduction
Managed Stackable Switch XSM7224S
• Use the product only with approved equipment.
• Allow the product to cool before removing covers or touching internal components.
• Operate the product only from the type of external power source indicated on the
electrical ratings label. If you are not sure of the type of power source required, consult
your service provider or local power company.
• To help avoid damaging your system, be sure that the voltage selection switch (if
provided) on the power supply is set to match the power available at your location:
- 115 volts (V), 60 hertz (Hz) in most of North and South America and some Far
Eastern countries such as South Korea and Taiwan
- 100 V, 50 Hz in eastern Japan and 100 V, 60 Hz in western Japan
- 230 V, 50 Hz in most of Europe, the Middle East, and the Far East
• Also, be sure that attached devices are electrically rated to operate with the power
available in your location.
• Use only approved power cables. If you have not been provided with a power cable for
your system or for any AC powered option intended for your system, purchase a power
cable that is approved for use in your country. The power cable must be rated for the
product and for the voltage and current marked on the product's electrical ratings label.
The voltage and current rating of the cable should be greater than the ratings marked on
the product.
• To help prevent electric shock, plug the system and peripheral power cables into properly
grounded electrical outlets.
• The peripheral power cables are equipped with three-prong plugs to help ensure proper
grounding. Do not use adapter plugs or remove the grounding prong from a cable. If you
must use an extension cable, use a three-wire cable with properly grounded plugs.
• Observe extension cable and power strip ratings. Make sure that the total ampere rating
of all products plugged into the extension cable or power strip does not exceed 80
percent of the ampere ratings limit for the extension cable or power strip.
• To help protect your system from sudden, transient increases and decreases in electrical
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
• Position system cables and power cables carefully; route cables so that they cannot be
stepped on or tripped over. Be sure that nothing rests on any cables.
• Do not modify power cables or plugs. Consult a licensed electrician or your power
company for site modifications.
• Always follow your local and national wiring rules.

Chapter 2. Hardware Installation |9
2
2. Hardware Installation
This chapter explains how to install the hardware for the Managed Stackable Layer 2+ 10G
Switch XSM7224S.
Package Contents
Each switch is packed and shipped separately. The package contains the following items:
• Managed Stackable Layer 2+ 10Gigabit Ethernet Switch with preinstalled software
• Power cord
• USB to serial converter
• Rubber footpads for tabletop installation
• Rubber caps for the SFP+ sockets
• Rack-mounting kit
• Null-modem serial cable (RS-232) with 9-pin connectors
• Resource CD: The CD either includes these documents or links to access them:
- ProSafe 7200 Managed Switch CLI Manual, Version 9.0
- NETGEAR 7000 Series Managed Switch Administration Guide
- NETGEAR Installation Guide for the XSM7224S Stackable Managed Switch
- This Hardware Installation Guide
• ProSafe NMS100 Network Management System 30-day trial CD-ROM
Protecting Against Electrostatic Discharge
WARNING!
Static electricity can harm delicate components inside your
system. To prevent static damage, discharge static electricity
from your body before you touch any of the electronic
components, such as the microprocessor. You can do so by
periodically touching an unpainted metal surface on the switch.

10 |Chapter 2. Hardware Installation
Managed Stackable Switch XSM7224S
You can also take the following steps to prevent damage from electrostatic discharge (ESD):
1. When unpacking a static-sensitive component from its shipping carton, leave it in the
antistatic package until you are ready to install it. Just before unwrapping the antistatic
package, discharge static electricity from your body.
2. Before moving a sensitive component, place it in an antistatic container or package.
3. Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads,
workbench pads, and an antistatic grounding strap.
Unpacking the Hardware
Check the contents of the boxes to make sure that all items are present before installing the
switch.
1. Place the container on a clean flat surface and cut all straps securing the container.
2. Unpack the hardware from the boxes.
Carefully remove the hardware and place it on a secure and clean surface. See
<pdf>“Select a Location” on page 2-10.
3. Remove all packing material.
4. Make sure that all items are present. See “Package Contents” on page -9.
Note: If any item is found missing or damaged, contact your local
NETGEAR reseller for replacement.
5. Inspect the products and accessories for damage. Report any damage immediately.
Installation
Install the equipment in the sequence presented in this section:
1. Select a Location. See “Select a Location” on page -10.
2. Install the Switch. See “Install the Switch” on page -11.
3. Check the installation. See “Check the Installation” on page -12.
4. Apply power and check the LEDs. See “Connect to Power and Check the LEDs” on
page -12.
Select a Location
The switch can be mounted in a standard 19-inch (48.26-centimeter) rack, wall-mounted, or
left freestanding (placed on a tabletop).