NETGEAR WND930 User manual

350 East Plumeria Drive
San Jose, CA 95134
USA
October 2014
202-11483-01
Outdoor High Power Wireless N
Access Point
Model WND930
Reference Manual

2
Outdoor High Power Wireless N Access Point
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product at
https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR
recommends registering your product through the NETGEAR website. For product updates and web support, visit
http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc.
and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice.
© NETGEAR, Inc. All rights reserved.

3
Contents
Chapter 1 Hardware Setup
System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Unpack Your Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Product Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Cable the Access Point for Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Chapter 2 Initial Setup
Connect to the Access Point and Log In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Specify the Access Point Name and Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Set the Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Configure the Basic IP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Configure the Access Point as a DHCP Server for Wireless Clients . . . . . . . . . 14
Configure the Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Turn On the Wireless Signal and Test Connectivity . . . . . . . . . . . . . . . . . . . . . . . 18
Plan Your Network Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Set Up Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Deploy the Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connect Optional External Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Chapter 3 Network Settings
Spanning Tree Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Set Up a Schedule for the Wireless Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Configure MAC Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Configure RADIUS Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configure Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Quality of Service Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Enable or Disable Wireless Multimedia QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Configure Advanced QoS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Wireless Bridging and Repeating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Set Up a Wireless Point-to-Point Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Set Up a Wireless Point-to-Multi-Point Bridge . . . . . . . . . . . . . . . . . . . . . . . . 39
Disable Ethernet LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Chapter 4 Manage the Access Point
Change the admin Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Reboot the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

4
Outdoor High Power Wireless N Access Point
Set Up a Remote Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Set UP SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Manage the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Back Up the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Restore the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Restore the Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Enable a Syslog Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Chapter 5 Monitoring
View System Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
View Wireless Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
View the Activity Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
View Network Traffic Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Enable Wireless Packet Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Chapter 6 Troubleshooting and Debugging
Troubleshooting with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
All LEDs Are Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
LAN LED Is Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
WLAN LED Is Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Cannot Connect to the Access Point to Configure It. . . . . . . . . . . . . . . . . . . . . . 59
Wireless Access to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Time-Out Error for URL or IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix A Supplemental Information
Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

5
1
1. Hardware Setup
This chapter covers the following topics:
•System Requirements
•Unpack Your Access Point
•Front Panel
•Product Label
•Cable the Access Point for Initial Setup
For more information about the topics covered in this manual, visit the support website at
http://support.netgear.com.
Firmware updates with new features and bug fixes are made available from time to time at
http://downloadcenter.netgear.com. Some products can regularly check the site and download
new firmware, or you can check for and download new firmware manually. If the features or
behavior of your product does not match what is described in this guide, you might need to
update your firmware.

Hardware Setup
6
Outdoor High Power Wireless N Access Point
System Requirements
Before installing the access point, make sure that your system includes the following:
•A 10/100/1000 Mbps local area network device such as a hub or switch, supporting IEEE
802.3af\ Power over Ethernet (PoE).
•The Category 5 UTP straight-through Ethernet cable with RJ-45 connector included in the
package, or one like it
•A web browser for configuration
•At least one computer with the TCP/IP protocol installed
•802.11b/g/n-compliant or 802.11a/n-compliant devices
Unpack Your Access Point
Your package contains the following items.
Wall-mounting bracket
Bracket
Pole-mount clamps (2)
Weatherproof
Access point cable glands (3)
Grounding
screws (2) screws (4)
Figure 1. Package contents

Hardware Setup
7
Outdoor High Power Wireless N Access Point
Front Panel
Ports, LEDs, and the Reset button are located on the front panel.
LEDs
Reset button
Figure 2. Front panel
Pressing the Reset button restores the factory settings. See Factory Settings on page 62.
LEDs
The LEDs light to indicate wireless access point activity.
Table 1. LEDs
LED Description
Power • Off. Power is off.
• Solid green. Power is on.
• Amber, then blinking green. A self-test is running or software is being
loaded. During startup, the LED is first steady amber, then goes off, and
then blinks green before turning steady green after about 45 seconds. If
after one minute the LED remains amber or continues to blink green, it
indicates a system fault.
Activity • Off. No network traffic is detected on the access point.
• Blinking green. Network traffic is detected on the access point.
2.4G WLAN • Off. The wireless interface is off.
• Solid green. The wireless interface is on.
• Blinking green. Wireless activity is detected on the 2.4G band.
5G WLAN • Off. The wireless interface is off.
• Solid green. The wireless interface is on.
• Blinking green. Wireless activity is detected on the 5G band.
Heater • Off. The heater is off.
• Solid green. The heater is on.
LAN ports • Off. No link is detected.
• Solid green. A link is detected.
• Solid amber. A 10/100/1000 Mbps speed connection is detected.
• Blinking amber. A 10/100/1000 Mpbs speed connection is detected.

Hardware Setup
8
Outdoor High Power Wireless N Access Point
Product Label
The product label is located on the rear panel. It includes the default access information and
the serial number and MAC address.
Figure 3. Product label
Cable the Access Point for Initial Setup
Before mounting the access point in a high location, first set up and test the unit to verify
wireless network connectivity.
Note: DHCP client is enabled by default in the access point. If your network
includes a DHCP server, the access point obtains an IP address from
the DHCP server. If a DHCP server is not detected in your network
after 30 seconds, the access point sets its IP address to a static IP
address of 192.168.0.100.
To cable your access point:
1. Using an Ethernet cable, connect power-sourcing equipment (PSE) to a PoE port on the
access point.
Note: You must supply either IEEE802.3at power to at least one LAN port or
IEEE802.3af power to two LAN ports to power the access point. You
mustsupplyIEEE802.3atpowerto both LANportsto receivePoEpower
out.

Hardware Setup
9
Outdoor High Power Wireless N Access Point
2. If a DHCP server is not connected to your network, configure a computer with a static IP
address of 192.168.0.210 and a subnet mask of 255.255.255.0.
3. Connect an Ethernet cable from a LAN port on the access point to a LAN port on the
computer.
4. Check the LEDs to verify that the access point is set up correctly.

10
2
2. Initial Setup
This chapter covers the following topics:
•Connect to the Access Point and Log In
•Specify the Access Point Name and Location
•Set the Time
•Configure the Basic IP Settings
•Configure the Access Point as a DHCP Server for Wireless Clients
•Configure the Basic Wireless Settings
•Turn On the Wireless Signal and Test Connectivity
•Plan Your Network Security
•Set Up Security Profiles
•Deploy the Access Point
•Connect Optional External Antennas

Initial Setup
11
Outdoor High Power Wireless N Access Point
Connect to the Access Point and Log In
You can connect to the access point’s web management interface to view or change its
settings.
To connect to the access point:
1. If a DHCP server is not connected to your network, configure a computer with a static IP
address of 192.168.0.210 and a subnet mask of 255.255.255.0.
2. Connect an Ethernet cable from a LAN port on the access point to a LAN port on the
computer.
During initial setup, use a wired Ethernet connection.
3. Launch a web browser.
4. In the address field of the browser, enter http://192.168.0.100.
A login screen displays.
5. Enter admin for the user name and password for the password.
The user name and password are case-sensitive.
The web management interface of the access point displays the General screen.
Specify the Access Point Name and Location
You must use a computer that is configured with a static IP address of 192.168.0.210 and a
subnet mask of 255.255.255.0. During initial setup, use a wired Ethernet connection from the
computer to the access point.
To specify the access point name and location:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.
The user name is admin and the default password is password. The user name and
password are case-sensitive.
4. In the Access Point Name field, type the access point name.

Initial Setup
12
Outdoor High Power Wireless N Access Point
This unique name is the access point NetBIOS name. The default access point name is
on the product label. The naming convention is netgearxxxxxx, where xxxxxxx represents
the last 6 digits of the access point MAC address. You can enter a unique name up to 15
characters long.
5. From the Country/Region list, select the region where the access point is located.
In the United States this setting cannot be changed. If your country or region is not listed,
check with NETGEAR support for the correct selection.
6. Click the Applybutton at the bottom of the screen.
Your settings are saved.
Set the Time
You must use a computer that is configured with a static IP address of 192.168.0.210 and a
subnet mask of 255.255.255.0. During initial setup, use a wired Ethernet connection from the
computer to the access point.
To set the time:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.
The user name is admin and the default password is password. The user name and
password are case-sensitive.
The General screen displays.
4. Select Configuration > System > Basic > Time.
5. Adjust the following fields:
•Time Zone. Select the local time zone for your access point. The default is
USA-Pacific. The access point gets the current time from the connected computer.
•NTP Client. Enable the NTP client to synchronize the time of the access point with an
NTP server. The Enable radio button is selected by default.

Initial Setup
13
Outdoor High Power Wireless N Access Point
Note: You need an Internet connection to get the current time using an NTP
client.
•Use Custom NTP Server. Select this check box if you use a custom NTP server. The
check box is cleared by default.
•Hostname / IP Address. Enter the host name or the IP address of the custom NTP
server. The default is time-b.netgear.com.
6. Click the Apply button at the bottom of the screen.
Your settings are saved.
Configure the Basic IP Settings
The default settings work in most cases, but you can change them as needed if your access
point is part of a complex LAN network.
You must use a computer that is configured with a static IP address of 192.168.0.210 and a
subnet mask of 255.255.255.0. During initial setup, use a wired Ethernet connection from the
computer to the access point.
To configure the basic IP settings:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.
The user name is admin and the default password is password.
The General screen displays.
4. Select Configuration > IP.
5. If necessary, specify the following settings:
•DHCP Client. By default, the Dynamic Host Configuration Protocol (DHCP) client is
enabled. If your LAN includes a DHCP server and you enable DHCP, the access point
gets its IP address, subnet mask, and gateway settings from the DHCP server when
the access point is connected to your LAN.

Initial Setup
14
Outdoor High Power Wireless N Access Point
•IP Address. The IP address of your access point. The default IP address is
192.168.0.100 when it does not get a dynamic IP address. To change it, enter an
unused IP address from the address range used on your LAN, or enable DHCP in a
network with a DHCP server.
•IP Subnet Mask. The access point calculates the subnet mask based on the IP
address that you assign. Otherwise, you can use 255.255.255.0 (the default) as the
subnet mask.
•Default Gateway. The IP address of the gateway for your LAN. For more complex
networks, enter the address of the router for the network segment to which the access
point is connected.
•Primary DNS Server. The IP address for the primary Domain Name Server used by
stations on your LAN.
•Secondary DNS Server.The IP address for the secondary Domain Name Server
used by stations on your LAN.
•Network Integrity Check. Select this check box to enable the access point to
validate that the upstream link is active before allowing wireless associations. If you
set this option you must ensure that your default gateway is configured.
6. Click the Apply button at the bottom of the screen.
Your settings are saved.
If you changed the subnet of the LAN IP address, you are disconnected from the access
point user interface. To reconnect, reconfigure your computer with a static IP address within
the new LAN IP subnet.
Configure the Access Point as a DHCP Server for Wireless
Clients
Your access point comes with a built-in DHCP server for wireless clients only, which can be
especially useful in small networks. You can enable and configure the DHCP server. The
access point will provide TCP/IP configuration for all wireless stations connected to it.
To configure the access point as a DHCP server for wireless clients:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.
The user name is admin and the default password is password.
The General screen displays.

Initial Setup
15
Outdoor High Power Wireless N Access Point
4. Select DHCP Server Settings.
5. Select the Enable radio button.
6. To specify the IP address range that the access point can assign, complete the Starting
IPv4 Address and Ending IPv4 Address fields.
7. In the Subnet Mask field, enter the subnet mask to be assigned to the wireless clients.
8. In the Gateway IP Address field, enter the IP address of the default network gateway for all
traffic beyond the local network.
9. Complete the fields to specify DNS servers and WINS servers if your network includes
them.
10. Enter the appropriate values in the Lease fields.
This is the lease time for the assigned IP for the wireless client. The client must renew the
lease based on the lease period.
11. Click the Apply button at the bottom of the screen.
Your settings are saved.
Configure the Basic Wireless Settings
You must use a computer that is configured with a static IP address of 192.168.0.210 and a
subnet mask of 255.255.255.0. During initial setup, use a wired Ethernet connection from the
computer to the access point.
To configure the basic wireless settings:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.

Initial Setup
16
Outdoor High Power Wireless N Access Point
The user name is admin and the default password is password.
4. Verify that the correct country or region is selected.
5. If you changed the setting, click the Apply button at the bottom of the screen.
Your settings are saved.
6. Select Configuration > Wireless.
By default, the wireless feature is turned on, and the Wireless On-Off Status field
displays OFF. For information, see Turn On the Wireless Signal and Test Connectivity on
page 18
7. Select a 2.4 GHz band wireless mode:
•11b. All 802.11b wireless stations can be used. (The 802.11g wireless stations can
still be used if they can operate in 802.11b mode.)
•11bg. Both 802.11b and 802.11g wireless stations can be used.
•11ng. All 11b, 11g, and 11ng wireless stations can be used. This is the default. If you
select this option, then two additional lists, Channel Width and Guard Interval,
display.
8. To specify 5 GHz mode settings, click the 802.11a/na tab.
Note: If you select a wireless mode and other settings on this screen are
disabled,thenyoumustselect theTurn Radio On checkboxtoenable
options on this screen.
9. Leave the Turn Radio On check box selected.
10. In the Wireless Network Name (SSID) field, type a wireless network name.

Initial Setup
17
Outdoor High Power Wireless N Access Point
This is the name of your wireless network. It is set to the default name of
NETGEAR_11na for 802.11a/n wireless mode and NETGEAR_11ng for 802.11b/g/n
wireless mode.
Note: The SSID of any wireless client must match the SSID you configured
in the access point. If they do not match, you cannot get a wireless
connection.
11. Leave the Broadcast Wireless Network Name (SSID) Yes radio button selected.
If you disable broadcast of the SSID, only devices that use the correct SSID can connect.
This nullifies the wireless network discovery feature of some products such as Windows
7, but the data is still fully exposed to a determined snoop using specialized test
equipment like wireless sniffers. By default, the Yes radio button is selected.
12. In the Channel / Frequency list, leave Auto selected.
When Auto is selected, the access point seledcts a channel with the least interference.
Do not change the wireless channel unless you experience interference (shown by lost
connections or slow data transfers). If this happens, you might need to experiment with
different channels to see which is the best. When selecting or changing channels, bear
these points in mind:
•Access points use a fixed channel. You can select the channel used. This allows you
to select a channel that provides the least interference and best performance.
•If you use multiple access points, it is better if adjacent access points use different
channels to reduce interference. NETGEAR recommends channel spacing between
adjacent access points of 5 channels (for example, use Channels 1 and 6, or 6 and
11).
•Wireless stations usually scan all channels, looking for an access point. If more than
one access point can be used, the one with the strongest signal is used. This can
happen only when the access points use the same SSID.
Note: If you use wireless bridging and repeating, you must select a specific
channel for your network. For more information, see Wireless Bridging
and Repeating on page 37.
13. From the list, select the MCS Index/Data Rate.
This is the transmit data rate of the wireless network. Depending on the band selected,
the set of rates varies. When the auto channel is enabled in the 802.11ng mode, then the
default channel width mode is 20 MHz. For information about the supported data rates,
see Technical Specifications on page 65.
14. Specify the channel width.
A wider channel improves the performance, but some legacy devices can operate only on
either 20 MHz or 40 MHz. In the Channel Width list, the following options are available:
•20 MHz. This is the static, legacy mode. It gives the least throughput.

Initial Setup
18
Outdoor High Power Wireless N Access Point
•40 MHz. This is the static, high-throughput mode. Legacy clients cannot connect in
this mode.
•20/40 MHz. This is the dynamic compatibility mode. Legacy clients can connect to 20
MHz and 11n clients can connect to 40 MHz.
15. From the list, select the guard Interval.
The guard interval protects from interference from other transmissions. The default is
Auto.
16. In the Output Power list, select the transmit power of the access point.
The options are Full, Half, Quarter, Eighth, and Minimum. Decrease the transmit power
if two or more access points are close together and use the same channel frequency. The
default is Full. The transmit power might vary depending on the local regulatory
regulations.
17. Click the Applybutton at the bottom of the screen.
Your settings are saved.
Turn On the Wireless Signal and Test Connectivity
By default, the access point wireless signal is off. After you configure the basic wireless
settings, turn on the wireless signal and verify that wireless clients can connect.
To turn on the wireless signal:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.
The user name is admin and the default password is password.
The General screen displays.
4. Select Configuration > Wireless > Basic > Wireless On-Off.
5. Select the On radio button.
6. Click the Applybutton at the bottom of the screen.
The access point broadcasts wireless signals.

Initial Setup
19
Outdoor High Power Wireless N Access Point
7. Verify that your wireless clients can connect to the access point.
When wireless connectivity is working, configure wireless security.
Plan Your Network Security
To prevent unauthorized access to your network, NETGEAR recommends that you use the
security features of your wireless equipment. You can enhance the security of your wireless
network in several ways:
•Use the WPA2 or Mixed WPA/WPA2 security option. A security option is the type of
security protocol applied to your wireless network. The security protocol encrypts data
transmissions and ensures that only trusted devices receive authorization to connect to
your network. Several types of encryption are available: Wi-Fi Protected Access II
(WPA2), WPA, and Wired Equivalent Privacy (WEP).
-WPA2 is the latest and most secure. NETGEAR recommends that you use this option
if your equipment supports it.
-WEP and TKIP provide only legacy (slower) rates of operation. NETGEAR
recommends AES encryption so that you can use the 11n rates and speed.
For more information, see Set Up Security Profiles on page 20.
•Keep watch over your wireless network. Regularly monitor the wireless stations that
are allowed to connect to your access point and make sure that all of them are legitimate.
For more information, see View Wireless Stations on page 53.
•Change the login password regularly. When you use the default login password, an
intruder can more easily figure out how to log in to the management interface of the
access point and change the settings. For more information, see Change the admin
Password on page 44.
Note: For additional wireless security, you can change the default network
key regularly. But whenever you change the network key, you must
reconnect all of the wireless devices. For more information, see Set
Up Security Profiles on page 20.
•Turn off the wireless radio. During the hours when your offices are closed, turn off the
wireless radio. For more information, see Set Up a Schedule for the Wireless Radios on
page 27.
•Turn off the broadcast of the wireless network name (SSID). If you disable broadcast
of the SSID, only devices that use the correct SSID can connect. This nullifies the
wireless network discovery feature of some products such as Windows XP, but the data is
still fully exposed to a determined snoop using specialized test equipment like wireless
sniffers. For more information, see Set Up Security Profiles on page 20.
•Restrict access based on MAC address. You can restrict access to only trusted
computers so that unknown computers cannot connect wirelessly to the access point.

Initial Setup
20
Outdoor High Power Wireless N Access Point
MAC address filtering adds an obstacle against unwanted access to your network. For
more information, see Configure MAC Authentication on page 28.
Set Up Security Profiles
Details of each wireless network are contained in a security profile. Each security profile
contains the following information:
•Profile name. This is the unique profile name. This value can be up to 32 alphanumeric
characters.
•SSID.This is the SSID associated with this profile.
•Security. This is the security standard, such as WPA2-PSK, that is associated with the
profile.
To change security profiles, you must use a computer that is configured with a static IP
address of 192.168.0.210 and a subnet mask of 255.255.255.0. During initial setup, use a
wired Ethernet connection from the computer to the access point.
To edit the security profile settings:
1. Launch a web browser on the computer that is connected to the access point.
2. In the address field of the browser, enter http://192.168.0.100.
A login prompt displays.
3. Enter the user name and password.
The user name is admin and the default password is password.
The General screen displays.
4. Select Configuration > Security.
For initial configuration and testing, the Security field for Profile 1 (the default profile) is
set to Open System and the SSIDs are set to NETGEAR_11ng and NETGEAR_11na.
Note: The SSID of any wireless client must match the SSID you configured
in the access point. If they do not match, you cannot get a wireless
connection.