Netum C200 User manual

Package Included:
1PC X Reader;
1PC X USB Cable;
1PC X Quick Setup Guide
Note: This is a general manual. If you need a full manual please download
it from our of�icial website: www.netum.net
NFC & RFID Reader/Writer

(1)
Trigger button
Battery Light/Read
Indicator Light
(Green/Blue/Red)
Bluetooth Light
Beeper
Type C
Lanyard Eyelet
Power Button
(On/Off)
Scanning Window
1.Product Information

(2)
2. Charge the battery
Red Light On: Charging
Red Light Off: Fully charged
DC Plug: V:5V; A>500mA
1). Turn it On
2). Connect reader with your
computer via USB cable (provided by
Netum)or take a DC plug and charge
it on an electrical wall outlet.
Power Button
“On”

(3)
3.Factory Reset
By following below steps will reset the reader.
Disconnect the USB cable→ switch power button to Off → press and hold the
button meanwhile switch it to ON →Hold on it for at least 15 seconds, release
it after you heard 1 beep
4.Reading Tags
1)Connet the reader with your device via USB cable or bluetooth (refer to
Connection Way section).
2) Hold the reader on the card, tag or smart device to be read.
3) For best results, card, tag, or smart device should be parallel to the reader.
4) Press the trigger button momentarily; blue led light will be on with a
short beep to indicate a successful scan.
For more con�igurations please download the software from below address:
https://www.netum.net/pages/netum-r�id-para-setting-software
Please program the reader in windows device. Currently it’s only compatible
with windows.
▶ If you want to change it to continuous scan mode, please download the
software and refer to scan mode in the Para Setting page.
Important Notes:
1)Key Delay Mode was set by default, press the button, green led light will
be on and off in 3s if it hasn’t read any cards .

(4)
2) If the reader fails to connect to your device via USB cable or bluetooth,
scanned characters will be stored in the reader. Once it’s connected with
your device, ,pressing the button for 5 seconds, scanned characters will be
uploaded and then been cleared.
5.Connection Way
The reader can be connected to your device via bluetooth, or USB cable.
Choose either way to get started.
1)USB Cable Connection
Get Started: Connect reader with your device via USB cable. If you use US
keyboard, it's plug and play. If you use other type of keyboard , please
con�igure the keyboard language in below software before using it.
▶ Open the software →C RFID Para Setting→ Keyboard layout

Red indicator light
Bluetooth Light
2)BLUETOOTH CONNECTION
• Bluetooth HID Mode:
▶ Open the software →Para Setting page→ BT Pro�ile Mode →HID
• Serial Port Pro�ile (SPP) / Apple Speci�ic Serial Pro�ile (BLE) Mode:
If you have an application that supports SPP or BLE this is the mode
recommended.
▶ Open the software →Para Setting page→ BT Pro�ile Mode
6.LED Activity/Prompt Tone /Indication under different
Connections :
(5)

Indication Bluetooth LED
Light Status
Indicator LED light Status Beep
Pattern
Red Green Blue
Working
Mode
ON
ON/OFF
Red led
�lashing
slowly
Red led
�lashing
quickly
Red Led
�lash twice
Red Led
�lashing
three times
Red Led
�lashing
�ive times
Blue LED on
and then off
(in 0.3s)
Blue LED on
and then off
(in 0.1s)
1 long beep
in 3 tones
1 short beep
2 beeps
3 beeps
5 beeps
Bluetooth Unpaired
Bluetooth Unpaired
Blue Led �lashing
slow
Bluetooth Pairing
Blue Led �lashing
quickly
Bluetooth paired
Blue Led �lashing
quickly and off in
30s if a connection
haven’t been made
Bluetooth HID
Mode
Blue Led on and
in solid blue
Bluetooth SPP/
BLE Mode
RFID searching for cards
Charging power/
Full charged
Low power warning,
power volume less
than 20%
Low power warning,
power volume
less than 10%
Power On/Bluetooth
Paired/ data uploaded
Successful Scan
Bluetooth unpaired/
successful scan in
low power
Data transmit failed
Fail to turn the
reader on
(6)

Note:
Please do not hesitate to contact us if you have any inquires.
Contact Information
Tel.: [phone]
Whatsapp: [phone]
Email: [email protected]
Addr.:Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51 Xiangshan
Avenue,
Ningxi Street, Zengcheng District, Guangzhou City, Guangdong Province, China
Name: APEX CE SPECIALISTS LIMITED
Add: UNIT 3D NORTH POINT HOUSE,NORTH POINT BUSINESS PARK, NEW
MALLOW
ROAD,CORK，T23 AT2P，IRELAND
Contact: Wells
Tel: [phone]
E-Mail: [e-mail]
Made in China
(7)