Netum RS-8000 User manual

Package Included:
1 x Scanner; 1 x Dock;
1 x USB cable; 2 x Baeries;
1 x Quick Manual;
Model:RS-8000/RS-9000
Bluetooth Ring Scanner
V20.12.31

1. Product Informaon
(1)
① Scanning Window
② Scanner LED
③ Baery Door
④ Buzzer
⑤ Trigger Buon
⑥ Adjustable Ring Belt
① Baery Charging Dock
② DC Port
③ Type C Port
④ Bluetooth LED
⑤ Transmission LED
⑥ Baery charging LED
⑦Scanner Power charging LED
1
2
3
4
5
6
1
2
3
4
5
6
7

2. Charge The Baery
2.1. Press and push up the
baery door
2.2. Insert baery and secure
baery door
(2)

3.Scanner's Bluetooth Connecon Status
Baery Dock LED Status：
1) Solid Blue- Bluetooth
Connected
2) Flashing Blue- Bluetooth
Disconnected/Bluetooth Pairing
(3)
4
32
1
① Scanner LED
1) Solid Red- Full Charged
2) Flashing Red- Charging
② Baery LED
1) Solid Red- Full Charged
2) Flashing Red - Charging
④ Bluetooth connecon status
1) Solid Blue- Scanner has connected with the dock
2) Flashing Blue- Scanner has disconnected with the dock
③ Transmission LED
1) Solid Green- No Transmit
2) Flashing Green- Transferring data
Bluetooth
LED

4. Setup Guide
(4)
Firmware Version
Read below command barcode to check scanner firmware version.
Barcode Programming
Netum barcode scanners are factory programmed for the most common
terminal and communicaons sengs. If you need to change these
sengs, programming is accomplished by scanning the bar codes in this
guide. An asterisk (*) next to an opon indicates the default seng.
Get Started
1）Pair Netum bluetooth (refer to the secon of “Bluetooth pairing”)
2）Setup keyboard language: US keyboard is set by default. If you use
other type of keyboard please refer to the secon of “keyboard language”.
3）Locate cursor on place where you want the data to be displayed aer
that you can start to scan.
Bluetooth Pairing
How to pair scanner's bluetooth with the dock ?
1) Connect the dock with your computer via USB
cable.
Firmware Version

(5)
Keyboard Language
For example If you use French Keyboard, scan command barcode of
“French keyboard ”. If you use a US keyboard you can ignore this step.
Important Note:
Default Idle Time: Scanner will power off automacally if device is not
connected in 3mins . If you want BLE and SPP mode, please contact us.
2) Scan QR code from the dock, Bluetooth paired once blue LED on the
dock turns to solid blue.
3) If you want to disconnect it with the dock and connect it with your
device, scan "Bluetooth HID" then pair Netum Bluetooth.
Bluetooth HID (Default)
* America EN keyboard French keyboard
Germany keyboard Italy keyboard

(6)
*Quit Offline Mode
Portugal keyboard Spain keyboard
UK keyboard Czech keyboard
Hungary keyboard Belgium FR keyboard
Data Uploading Mode
If you are heading for a working area which lies outside the bluetooth signal
range, you may acvate scanner’s store mode, following steps described be-
low. Under this mode,all scanned data will be stored directly into the buffer
memory of the device. Furthermore, the data entries will be permanently
saved in the buffer memory prior to the manual upload into the working
staon, so that you may upload them when you are near your working device.
By scanning the following barcode, the device leaves the offline mode, normal
mode will be reinialised.

(7)
Output Total Entry
By scanning the following barcode, the gross quanty of the uploaded data
entries will be summarised .
Offline Mode
By scanning the following barcode, the offline mode will be acvated.
Clear Memory
By scanning the following barcode, all data in the buffer memory will be
deleted.
Output Stored Data
By scanning the following barcode, all data entries in the buffer memory
can be manually uploaded aer reconnecng to the working staon.
Output Total Entry
Offline Mode
Clear Memory
Output Stored Data

(8)
Idle me
Scanner will turn to sleep aer idle/inacve for 1min
Scan "Disable module Idle me" before you doing any other setup from this
secon.
Get Baery Volume
Scan below command barcode to get baery rough volume.
1) Voltage < 3.5V, Low baery Volume, there will have 5 beeps aer each
scan. Scanner can not be able to read any barcodes.
2) 3.7V< Voltage < 3.5V, Low baery Volume, there will have 2 beeps aer
each scan. Scanner sll be able to read barcodes.
3) Voltage >4.2V , Full Volume
Power Off Disable Sleep Mode
* 3mins 1Hour
Baery Rough Volume

(9)
IOS Keyboard POP UP/HIDE
During the scanning IOS keyboard can be hided or popped up by scanning
below command barcode.
1)Scan this barcode at Bluetooth HID connected state on IOS device, popup
IOS keyboard.
2) Popup IOS keyboard by hold trigger 4 seconds.
3) Popup IOS keyboard by double click trigger.
Note: Two short beeps aer scan indicates disable, one long sound with
three tones indicates enable.
IOS Keyboard POP UP/HIDE
Enable/Disable
Enable/Disable