New England Arbors Newport Arbor Quick start guide

13
Part # Description Quantity "TTFNCMZ.PVOUJOH*OTUSVDUJPOT/FXQPSU"SCPS- Read instructions through carefully before
beginning assembly.
- Identify each component from material list.
- When assembling components, place on a
non-abrasive surface to avoid scratches.
- Do not use excessive force when assembling
components.
- In the event of missing or defective parts,
please call our customer service department
at 1-800-282-9346 (ext.#20).
(FOFSBM*OGPSNBUJPO- Cordless drill & #2 Robertson bit
- Tape measure
- Level
- Shovel
5PPMT3FRVJSFE1 4” sq. x 84”(Std) or 120”(Pro) Posts
2 84” Long molded arches
3 4” sq. Locking arch/post inserts
4 4” sq. Trim caps
5 1 3/4” sq. Pergola end caps
6 1 3/4” sq. x 31 5/8” Top/bot rails
7 1 3/4” sq. x 31 5/8” Middle rails
8 1 3/4” sq. x 39” Filters
9 7/8” x 1 1/2” x 58” Spindles
10 Keystones (base & locking top)
11 Hardware kit (Includes):
1 1/2 oz. tube of glue
3/4” Stainless screws
3” Stainless screws
Cap/washer assembly (tan model only)
4
2
4
4
20
4
2
10
10
2
2
32
20
52
- 4” sq. treated wood posts.
- Pre-mix concrete (recommended for added strength
and stability, especially when attaching a gate).
.BUFSJBMT*ODMVEFE87 1/2”
50”
.BUFSJBMT0QUJPOBMPart 1
Part 2
Part 3
Part 4
Part 6
'JHProduct dimensions & part
identification.
'JHPost layout for installation.
24”
Opening
58”
93 3/4”
50”
If you have any questions concerning the assembly or installation of this product and require assistance, please call our Customer service
department at 1-800-282-9346 (ext.#20), Weekdays from 8:00 am. to 4:00 pm. Eastern standard time.
If you have any comments or suggestions about our product or service, please let us know! Call: 1-800-282-9346 (ext.#24). or E-mail:
[email protected]
To learn more about us, visit us on the web at: www.newenglandarbors.com
2VFTUJPOT Part 5 Part 8
Part 9
Part 7
32”
Ver 1.07
Part 10
14 Determine the location for your arbor, and measure out the exact
distance between the posts as shown in (Fig. 2) on the front
cover. Once you’ve verified the measurements, mark each post
location on the ground. Note: If you’ve purchased the Aussie
Auger mounts, please refer to the their instructions to complete
the installation.
15 Dig four holes in the marked locations. For the “pro model”
holes will need to be 36” deep. For the standard model we
recommend a minimum depth of 24” to provide a secure footing.
If you’ve not purchased Aussie Auger mounts, use 4x4 treated
posts to mount your arbor. Slide them inside the vinyl posts and
fasten with screws (not included) through the bottom just below
the base moldings.
Slide each trim cap up to the underside of the arch, and press the
cap firmly against the flat of the arch. Hold for a few seconds to
allow the glue to bond. Using four 3/4” screws per post, fasten
through the post & into the arch insert just below each trim cap.
Note: If your arbor is tan, use the included cap/washer
assemblies along with the screws.
16 With assistance, place your arbor into the holes and check each
post for level. Verify the measurements between the posts, and
make adjustments as needed. When the desired orientation has
been achieved, fill in the holes. We “strongly” recommend using
concrete for this, especially if you have plans to attach a gate to
your arbor.
17
Brace the arbor to keep it steady while the cement cures. Make
sure to slide the base moldings down to ground level when
finished. There should be a least a 2” gap between the top of the
base molding and the bottom rail. If you have not purchased the optional
trim kit, please disregard this step.
84” 45”
'JHCap/washer assembly.

1
3
4
5
6
Without inserting them completely, set one bottom rail (part 6)
and one middle rail (part 7) into the holes in one of the posts
(part 1) as shown. Insert the spindles (part 9) through the top rail
and into the bottom rail.
2
7
9
10
11
12
Run a bead of glue on the inside lip of a pergola end cap (part 5).
Push the cap onto the end of the filter and hold it steady for a
few seconds. Repeat this for each of the remaining caps, then
allow about 15 to 20 minutes for the glue to set up.
8
Lift up on the panel and slip the top rail (part 6) onto the ends of
the spindles. Push down on the end of each rail until the tabs are
“locked” into the holes in the post.
Set out a second post. Flip the entire panel over and line up the
rail ends with the corresponding holes in the post. As in step 2,
push the end of each rail into the holes until the “locking” tabs
are completely inserted. Repeat steps 1 through 3 for the second
side panel.
Slide two of the base moldings onto the bottom of each post as
shown. Push the base moldings onto the posts until they touch
the bottom rail. Repeat this for the other side panel. If you have not
purchased the optional trim kit, please disregard this step.
Lay out both assembled arches (part 2) on a level surface. Using
one filter (part 8) as a guide, space the arches apart until the
holes in the filter line up with the “guide pins” in the arches.
Run a bead of glue around the guide pin and in the recess of
each arch.
Slip the trim caps (part 4) over the top of the posts. Slide the
first one down until it sits just above the top rail, and the second
one down only a few inches. Repeat this for all 8 trim caps. If you
have not purchased the optional trim kit, you will have only 4 trim caps.
Take the keystone base and top (part 10) and connect them over
the middle of the arch as shown. Make sure the pins in the base
are correctly inserted into the holes in the top. Push the two
pieces firmly together. Repeat this for the second arch. No glue
is required for this step.
Slip each locking post insert (part 3) into the bottom of each
arch. Push firmly until they “snap” into place. Again, no glue is
required for this step.
Run a bead of glue around the inside of the top of each post.
With assistance, lay down the side panels and insert the
completed arch assembly into the open ends of the posts as
shown. Again with assistance, stand the arbor up and check to
make sure the arch assembly has been completely inserted into
the posts.
Place the filter onto the guide pins. Push down firmly until it
“snaps” in place and apply pressure for a few seconds to allow
the glue to bond. Take one 3” screw and fasten each end of the
filter through the top of the arch, making sure not to hit the pins
below. Note: If your arbor is tan, use the included cap/washer
assemblies (Fig 3) along with the screws. Repeat steps 6 & 7 for
the remaining filters.
Make sure the arbor is secure and standing on even ground. Run
a bead of glue along the top half of each trim cap sitting directly
under the arch.