NexSens Technology X2-CB-C User manual

X2CBC BUOYMOUNTED DATA LOGGER
QUICK START GUIDE
IMPORTANT - BEFORE FIELD DEPLOYMENT: Completely configure new X2 systems with sensors and a web connec-
tion in a nearby work area. Operate the system for several hours and ensure correct sensor readings. Use this test run
to become familiar with the features and functions.
To get started:
a. Go to WQDataLIVE.com
b. Create a new account or sign into an existing
account.
c. Choose or create the project that will contain
the data logger by selecting the Projects link
from the bottom right footer of the page.
d. Go to the ADMIN tab located at the top of the
project dashboard and click Settings.
From there, choose the Project/Site pull down
menu and select the site for the new data logger.
a. If a site has not been created, select New Site.
Create and save the site before entering the
claim code.
Enter the claim code listed below into the space
provided under Assigned Devices.
Click Add Device.
a. The new device should be visible in the
Assigned Devices list.

If cellular service is not purchased through
NexSens, visit the article link below for steps on
how to setup the cell modem.
a. nexsens.com/x2apn

Use the CONNECT software to ensure the proper
scripts are enabled for each sensor.
a. nexsens.com/conncss

Remove one blank sensor plug from an 8-pin port
(i.e., P0, P1, or P2) for each sensor.
a. Connect all sensors to the desired ports.
Note: Only one RS-232 sensor can be plugged into
each P0, P1, or P2 port, (i.e., either P0-A or P0-B.).
Ensure that all SDI-12 and RS-485 sensors have
unique addresses.

Overview
The X2-CB buoy-mounted data logger with cellular te-
lemetry includes an integrated modem. Five sensor ports
provide industry standard protocols including SDI-12, RS-
232, and RS-485. The Solar/COM port offers direct com-
munication (serial to PC) and power input. The X2-CB is
powered from the CB-Series buoy’s solar rechargeable
battery reserve.
Data is accessed and stored on the WQData LIVE web
datacenter. An easy-to-use dashboard and built-in sensor
library automatically facilitate setup and configuration.
What’s Included?
(1) X2-CB buoy-mounted data logger
(5) Sensor port plugs, (3) spare orings
(1) Power port plug, (2) spare orings
(1) Oring grease
(2) Spare sensor port plugs
(1) Wireless antenna (installed on telemetry units only)
(1) Quick start guide
Figure 1: X2-CB Buoy-Mounted Data Logger

937-426-2703
www.nexsens.com
2091 Exchange Court
Fairborn, Ohio 45324
Buzzer Event
When power is
applied
Beep Type
During telemetry
connection
Status
One short
beep
Two short
beeps
Three short
beeps
System boot
successful
Connection
successfully
established
No signal/connection
failed
During telemetry
connection
Buzzer Pattern Indicators
Table 1: X2-CB Buzzer Pattern Indicators.
During sensor
detection
Three second
beep duration
WQData LIVE
setup
successful
1
Remove the SOLAR/COM blank plug from the
6-pin port.
a. Connect the 6-pin solar panel plug to power
the X2-CB.
b. The device will beep once when powered.
Wait up to 60 seconds for the system to check
cellular coverage.
a. Two consecutive beeps = adequate signal
b. Three consecutive beeps = no signal
• If three beeps are heard, move the X2-CB
into an area with strong cellular coverage.
• Check cellular coverage through CONNECT
using the link: nexsens.com/x2apn
 After 20 minutes, refresh WQData LIVE and
confirm all sensor parameters are shown and
valid sensor readings appear.
a. The device will beep for a duration of three
seconds when detection is complete.
For additional information, please reference the X2-CB Resource Library on the NexSens Knowledge Base.
nexsens.com/x2cbkb
1WQData LIVE setup is automatically done after sensor
detection.
Figure 2: Steps 7 & 8 - Connect sensors to the 8-pin
ports and connect the solar panel plug to the 6-pin
port.