Next 866903 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Made in China.
CARE INSTRUCTIONS
this item correctly.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• Do not use furniture polish.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
PRODUCT INFORMATION
• Made from MDF.
• Maximum weight this product can hold is 10 kg
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Carefully check that you have all parts before beginning assembly.
866903 ASHTON CUBBY WIDE
Page 1 of 6

FITTINGS
PARTS
Page 2 of 6

1. Insert 7 x dowels C into panel (1), and insert 11 x
cambolts A into panel (1) with a screwdriver.
2. Insert 5 x dowels C into side panel (2), and insert 7
x camblots A into side panel (2) with a screwdriver.
3. Insert 5 x dowels C into side panel (7), and insert 7 x
cambolts A into side panel (7) with a screwdriver.
1. Insert 4 x dowels D into shelf (3).
2. Insert 2 x dowels C into shelf (4), and insert 4 x
cambolts A into shelf (4) with a screwdriver.
STEP ONE
STEP TWO
Page 3 of 6

1. Attach 4 x panels (6), shelf (3) and shelf (4) together
using 4 x cam-locks B with a screwdriver I. Ensure
the arrow indicators are pointing to the panel edges
and ensure the cambolts locate properly into the cam-
locks before tightening with a screwdriver.
1. Attach above assembled unit and back panel (5) to
side panel (7) using 4 x cam-locks B. Please note the
cam-locks are towards different faces. Ensure the
arrow indicators are pointing to the panel edges and
ensure the cambolts locate properly into the cam-
locks before tightening with a screwdriver.
STEP THREE
STEP FOUR
Page 4 of 6

1. Fasten back panel to the unit using 6 x screws E
with a screwdriver, and attach side panel (2) to the
unit using 4 x cam-locks B. Please note the cam-
locks are towards different faces. Ensure the arrow
indicators are pointing to the panel edges and ensure
the cambolts locate properly into the cam-locks
before tightening with a screwdriver.
1. Attach top panel (1) to the unit using 8 x cam-locks
B with a screwdriver. Ensure the arrow indicators are
pointing to the panel edges and ensure the cambolts
locate properly into the cam-locks before tightening
with a screwdriver.
1. Fasten back panel, both side panels and top panel
using 9 x cam-locks B with a screwdriver. Ensure the
arrow indicators are pointing to the panel edges and
ensure the cambolts locate properly into the cam-
locks before tightening with a screwdriver.
2. Attach 4 x knobs F to the unit using 4 x screws G
with a screwdriver.
STEP FIVE
STEP SIX
STEP SEVEN
Page 5 of 6

1. Slide each of 6 x paper cards H into each holder as
shown.
1. Use the template provided to mark on the wall the
position of wall-mounted fixings.
2. Use a spirit level to check that the marks are level.
Warning:
NB: Wall fixings are not included - please source
suitable fixings for your wall type. If in doubt please
consult a qualified trades person.
3. Drill into the wall, insert raw plugs into wall
4. Insert Screws from the front through the unit into
the wall
Always ensure intended wall area to be drilled is free
from hidden electrical wires, water and gas pipes.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP EIGHT
NB: Place the template over the back of the Cubby to
ensure that the holes match the position of the hooks
before drilling into your wall.
Page 6 of 6