Next CORSICA 664575 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services
Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
664575 CORSICA BENCH SET
664575 CORSICA BENCH SET664575 CORSICA BENCH SET
664575 CORSICA BENCH SET
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Keep fittings out of children's reach and keep children well away from the construction area.
PRODUCT INFORMATION
• We recommend that the packaging is used to protect the surfaces during assembly.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• A minimum of two persons is required to assemble this product.
CARE INSTRUCTIONS
• Made from honeycomb board,partical board & MDF with a wood effect finish.
• Made in China.
• Do not use furniture polish.
Page 1 of 6

PARTS
FITTINGS
DX1
CX30
BX4AX44 EX1 FX36
12*60mm
GX12 HX36 IX36 JX12
6*70mm 21*84mm
13.5mm8*31*15mm 8*70mm8*100mm
KX24
1. Insert 4 x nuts (J) into panels 5 (x2) & 4 (x2).
2. Insert 4 x bolts (G) into insert nuts(J) fixed on panels 5
(x2) & 4 (x2) and turn bolts (G) clockwise until tight by
hands.
3. Insert 8 x bolts (G) into nuts fixed on panels 5 (x2) & 4
(x2) and turn bolts (G) clockwise until tight by hands.
x 2 units
STEP ONE
G
J
G
G
G
J
J
5
4
Page 2 of 6

1. Glue and insert 20 x wooden dowels (A) into panels 2
(x2), 3 (x2) & 1.
1. Glue 8 x wooden dowels (A).
2. Attach panels 4 (x2) & 5 (x2) to panels 2 (x2) .
3. Slot 4 X metal pieces (H) onto bolts (G) and thread 4 X
springs (I) onto bolts (G) then screw 4 X metal nuts (F)
with spanner (E) .
Note : Do not tighten the metal nuts (F) until
STEP TWO
STEP THREE
A
A
A
A
B
A
A
B
B
A
A
1
2X2
3X2
B
5
2
Note : Do not tighten the metal nuts (F) until
"STEP FIVE " .
x2 unit
1. Attach panels 3 (x2) to panel 1 with 6 x screws (C) by
using an Allen key (D).
STEP FOUR
G
BH
4
1
3
C
D
C
Page 3 of 6

1. Glue 12 x wooden dowels (A) .
2. Attach the assembled frame (x2) to panel 1 .
3. Slot 8 x metal pieces (H) onto bolts (G) and thread 8 x
springs (I) onto bolts (G) then screw 8 x metal nuts (F)
with spanner (E) .
4. Tighten the metal nuts (F) on panels (2) x 2.
Please note :We recommend that the packaging
is used to protect the surfaces during
assembly.
1.Tighten the panels 3(x2) to panel 1 with 8 x screws (C)
by using an Allen key (D).
STEP FIVE
STEP SIX
3
3
4
5
4
5
1
BH
B
D
C
C
1. Insert 8 x nuts (J) into panels 9(x4) & 10 (x4) .
2. Insert 8 x bolts (K) into insert (J) nuts fixed on panels 9
(x4) & 10 (x4) and turn bolts (K) clockwise until tight by
hands.
3. Insert 16 x bolts (K) into nuts fixed on panels 9 (x4) &
10 (x4) and turn bolts (K) clockwise until tight by hands.
x4 unit
STEP SEVEN
3
3
C
C
Page 4 of 6

1. Glue and insert 24 x wooden dowels (A) into panels 6
(x2), 7 (x4) & 8 (x4).
x2 unit
1. Glue 8 x wooden dowels (A) .
2. Attach panels panels 9 (x4) & 10 (x4) to panels 7 (x4) .
3. Slot 8 X metal pieces (H) onto bolts ( K ) and thread 8 X
springs (I) onto bolts (K) then screw 8 X metal nuts (F)
with spanner (E) .
Note : Do not tighten the metal nuts (F) until
"STEP ELEVEN" .
STEP NINE
STEP EIGHT
K
"STEP ELEVEN" .
x4 unit
STEP TEN
1. Attach panels 8 (x4) to panels 6 (x2) with 4 x screws
(C) by using an Allen key (D).
K
Page 5 of 6

1. Glue 24 x wooden dowels (A) .
2. Attach the assembled leg frame ( x4) to panels 6 (x2) .
3. Slot 16 x metal pieces (H) onto bolts ( K ) and thread 16
x springs (I) onto bolts (K) then screw 16 x metal nuts
(F) with spanner (E) until tight .
4. Tighten the metal nuts (F) on panels (7) x 2.
Please note : We recommend that the packaging
is used to protect the surfaces during
assembly.
x2 unit
1. Tighten panels 7(x4) to panels 6 (x2) with 12 x screws
(C) by using an Allen key (D).
STEP TWELVE
STEP ELEVEN
x2 unit
1.Turn over the products .Two person are required.
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
STEP THIRTEEN
6
Page 6 of 6