Next ASHTON GLAZED SIDE 855468 User manual

Tools Needed
Hel
p
line
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• For general cleaning, periodically dust with a soft cloth.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Made from MDF with paintedfinish.
CARE INSTRUCTIONS
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We recommend that the packaging is used to protect the surfaces during assembly.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Made in China.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• A minimum of 2 persons is required to assemble this product.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
PRODUCT INFORMATION
• Not suitable for use in bathrooms.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
855468 ASHTON GLAZED SIDE
Page1of5

1. Attach stopper (F) to top panel 1 with 2 x
screws (G) and tighten.
1. Insert 7 x cambolts (A) and 1 x wooden dowel
(C) into side panel 2-L.
2. Attach 2 x shelf panels 7, back lower rail 8 and
front lower rail 9 to side panel 2-L.
3. Insert 7 x camlocks (B) into 2 x shelf panels 7,
back lower rail 8 and front lower rail 9. Ensure the
arrow indicator is pointing towards the panel edge
before tightening with a screwdriver.
STEP TWO
STEP ONE
PARTS
FITTINGS
(1) Top Panel x 1
(7) Shelf Panel x 2
(2) Side Panel (L&R) x 2
(10) Door Panel x 1
(3) Bottom Panel x 1
(5) Back Panel x 1
(4) Back Panel x 1
(6) Back Panel x 1
(9) Front Lower Rail x 1
(8) Back Lower Rail x 1
GG
1
F
A
B
B
B
B
B
B
B
AA
A
A
A
A
C
7
7
98
2-L
Page2of5

1. Insert 7 x cambolts (A) and 1 x wooden dowels
(C) into side panel 2-R.
2. Attach side panel 2-R to the assembled unit.
3. Insert 7 x camlocks (B) into 2 x shelf panels 7,
back lower rail 8 and front lower rail 9. Ensure the
arrow indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 4 x wooden dowels (C) into bottom panel
3.
2. Attach bottom panel 3 to the assembled unit
with 4 x screws (E) and tighten with a screwdriver.
1. Insert 4 x cambolts (A) and 4 x wooden dowels
(C) into top panel 1.
2. Attach top panel 1 to the assembled unit.
3. Insert 4 x camlocks (B) into side panels 2 (both
L&R). Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
STEP FOUR
STEP THREE
STEP FIVE
BB
BA
B
B
7
7
9
8
AA
AAA
A
BB
2-L
2-R
C
C
C
C
E
E
E
3
2-R
2-L
B
B
BB
AA
AA
C
C
C
C
1
2-R
2-L
Page3of5

1. Attach back panel 4, back panel 5 and back
panel 6 to the assembled unit with 23 x screws (D)
and tighten.
1. Attach 2 x hinges (H) to door panel 10 with 4 x
screws (J) and tighten.
2. Attach 1 x handle (L) to door panel 10 with 1 x
bolt (K) and tighten.
3. Attach 1 x rubber pad (N) to door panel 10.
1. Attach door panel 10 to the assembled unit with
4 x screws (J) and tighten with a screwdriver.
Note: The gaps between the doors and frame can
be changed by making adjustments to hinges with
a screwdriver. Refer to adjustment diagrams.
Laterally (Side to Side)
Front to back
Vertically ( up and down)
STEP EIGHT
STEP SIX
STEP SEVEN
J
J
J
J
J
10
2-L
2-R
D
D
DD
D
D
D
D
DD
DD
DD
D
D
D
D
D
D
D
D
4
5
6
J
J
JJ
10
H
H
L
K
H
JJ
N
Page4of5

1. Use screw (C) and washer (B) to secure the
n
y
lon stra
p
(
A
)
to the to
p
p
ane
l
2. Secure the other end of the strap to the wall
with an appropriate screw and wall plug for your
wall type. To hide the strap behind the unit, drill
the holes lower than the to
p
of uni
t
Warning : Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
p
i
p
es.
NB : Wall fixings are not included-please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP NINE
SCREW
TOP
Page5of5