Next MILANO 896267 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Keep fittings out of children's reach and keep children well away from the construction area.
ASSEMBLY INSTRUCTIONS
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
896267 MILANO BLACK GLOSS
SMALL SIDEBOARD
• Wall fixings are not included.
• A minimum of two persons is required to assemble this product.
• Do not use furniture polish.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Made in China.
CARE INSTRUCTIONS
•Gloss finishes are prone to light surface scratch and it is therefore very important that
you care for this item correctly.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
PRODUCT INFORMATION
• Made from PB,MDF,hollow board & Honeycomb board with a pvc foil finish.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft cloths
(including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try your cloth in
an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for cleaning is included
within the hardware pack
Page 1 of 8

FITTINGS
PARTS
MX2 NX8LX1 OX1
(8*30mm) (6*30mm)
KX9
HX12 IX2 JX4DX27
CX3
BX11AX26 EX27 FX2 GX18
Please note: Remove the protective film after assembly of this product unless it is stated in
the steps to do so - this will prevent accidental scratches during assembly
1.Attach panels 14 , 15 & 18 to panel 20 with
6 x screws (G) and tighten with a screwdriver.
X 2
STEP ONE
14
15
20
G
G
G
X 2
Page 2 of 8

1. Slide panel 11 into the assembled drawer frame.
2. Repeat STEP ONE to STEP TWO for the
other drawer frame.
1. Insert 3 x cambolts (E) into panel 19 and
tighten with a screwdriver.
2. Glue and insert 3 x small wooden dowels (B)
into panels 14 , 15 & 18.
3. Attach panel 19 to the assembled drawer frame.
4. Insert 3 x camlocks (D) into panels 14 , 15 & 18.
Ensure the arrow indicators are pointing
towards the panel edges before tightening
with a screwdriver.
STEP TWO
STEP THREE
11
20
EE
19
1. Insert 3 x cambolts (E) into panel 13 and
tighten with a screwdriver.
2. Glue and insert 3 x small wooden dowels (B)
into panels 14 ,15 & 18.
3. Attach panel 13 to the assembled drawer frame.
4. Insert 3 x camlocks (D) into panels 14 , 15 & 18.
and tighten with a screwdriver.
STEP FOUR
E
E
13
13
D
D
D
B
B
C
C
Page 3 of 8

1. Attach panels 16 , 17 & 18 to panel 21 with
6 x screws (G) and tighten with a screwdriver.
1. Slide panel 11 into the assembled drawer frame.
STEP SIX
STEP FIVE
17
21
G
G
11
1. Insert 3 x cambolts (E) into panel 12 and
tighten with a screwdriver.
2. Glue and insert 5 x small wooden dowels (B)
into panels 16 , 17 & 18.
3. Attach panel 12 to the assembled drawer frame.
4. Insert 3 x camlocks (D) into panels 16 , 17 & 18.
and tighten with a screwdriver.
STEP SEVEN
16
17
21
17
16
18
C
C
B
B
D
D
E
EE
12
12
Page 4 of 8

1. Insert 8 x cambolts (E) into panel 9 and
tighten with a screwdriver.
1. Attach panel 9 to panels 3 ,1 & 2 with
9 x screws (K) using an Allen key (L) to tighten.
STEP EIGHT
STEP NINE
9
1
2
1. Glue and insert 8 x big wooden dowels (A)
into panels 4 (x2).
2. Attach panels 4 (x2) to panels 1 & 2 .
STEP TEN
9
3
A
A
A
A
Page 5 of 8

1.Insert 4 x cambolts (E) into panels 7 & 24 and
tighten with a screwdriver.
2. Glue and insert 4 x big wooden dowels (A) into
panels 6 (x2).
3. Attach panels 7 & 24 to panels 6 (x2) .
Note :Pls note the gloss pvc foil must be faced
outside when assembling.
4. Insert 4 x camlocks (D) into panels 6 (x2) and
tighten with a screwdriver.
1. Glue and insert 8 x big wooden dowels (A) into
panel 9.
2. Attach the assembled frame to panel 9.
3. Insert 8 x camlocks (D) into panels 6 (x2), 7 & 24
and tighten with a screwdriver.
4. Please remove the protective film from the
outside surface of panels 6 (x2) & 7.
STEP ELEVEN
STEP TWELVE
9
1. Carefully turn up the assembled unit as shown.
2. Slide panels 10 & 22 into the back panel groove.
STEP THIRTEEN
3
1
2
Page 6 of 8

1. Insert 6 x cambolts (E) into panel 8 and
tighten with a screwdriver.
2. Glue and insert 6 x big wooden dowels (A) into
panels 3,1 & 2.
3. Attach panel 8 to the assembled unit.
4. Insert 6 x camlocks (D) into panels 3,1 & 2.
and tighten with a screwdriver.
1. Insert 8 x fittings (N) into the required position
of panels 3 & 1.
2. Insert panels 5 (x2) onto the fittings (N) .
3. Use 2 x stickers (F) to cover the camlock holes
on panel 3 .
STEP FOURTEEN
STEP FIFTEEN
E
E
E
3
1
2
NF
1. Insert the drawer units to the assembled unit as
shown.
STEP SIXTEEN
19
12
13
N
N
3
1
5
5
Page 7 of 8

1.Secure 2 x fittings (M) to panel 23 with
4 x screws (J) as shown.
2. Please remove the protective film from the
outside surface of panel 23.
3.Attach door handles (O) to the panel 23 with
screws provided.
4.Insert panel 23 into the groove of the top
panel 8 as shown. Lift the door panel at an angle
and slot into the groove in panel 8, slide the
underneath towards panel 9 and locate the
rollers into the runner in panel 9.
1. Insert 12 x plastic fasteners (H) into the back panel
grooves and tighten with screws provided.
STEP SEVENTEEN
STEP EIGHTEEN
H
H
M
M
J
J
23
23
1. Using screw and washer secure the
2 x nylon straps (I) to the back of top panel.
2. Secure the other end of the strap to the wall
with an appropriate screw and wall plug
for your wall type (not provided).
To hide the strap behind the unit ,drill the hole
lower than the top of unit.
Warning:
Always ensure intended wall area to be
drilled is free from hidden electrical wires,
water and gas pipes.
NB:Wall fixings are not included-Please source
suitable fixing for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP NINETEEN
H
H
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 8 of 8