Next SOUTHPORT 855825 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• Made from MDF with painted finish.
PRODUCT INFORMATION
• Made in China.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer
finish.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
855825 SOUTHPORT SINK CONSOLE
Page1of6

1. Insert 2 x wooden dowels (D) into bottom panel
3.
2. Attach lower front rail 6 to bottom panel 3 with
3 x screws
(
F
)
and ti
g
hten.
1. Insert 5 x cambolts (A) and 5 x wooden dowels
(C) into side panel 2-L.
2. Attach top front rail 4, back rail 5, back rail 7
and shelf panel 9 to side panel 2-L.
3. Insert 5 x camlocks (B) into top front rail 4,
back rail 5, back rail 7 and shelf panel 9. Ensure
the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
PARTS
STEP TWO
STEP ONE
FITTINGS
(1) Top Panel x 1 (2) Side Panel (L&R) x 2 (3) Bottom Panel x 1 (4) Top Front Rail x 1
B
C
2-L
BC
9
5
7
C
C
B
B
BC
4
3
F
D
D
F
F
Page2of6

1. Insert 5 x cambolts (A) and 5 x wooden dowels
(C) into side panel 2-R.
2. Attach side panel 2-R to the assembled unit.
3. Insert 5 x camlocks (B) into top front rail 4,
back rail 5, back rail 7 and shelf panel 9. Ensure
the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
1. Insert 4 x wooden dowels (C) into bottom panel
3
2. Attach the bottom panel 3 to the assembled unit
with 4 x screws (E) and tighten.
1. Attach top panel 1 to the assembled unit with 4
x bolts (P) and tighten.
STEP FOUR
STEP FIVE
STEP THREE
2-L
2-R
9
7
5
B
B
C
C
C
C
B
B
4
B
C
1
P
P
2-L
Page3of6

1. Attach 4 x hinges (H) to door panel 10 (both
L&R) and with 8 x screws (J) and tighten.
2.Attach 2 x handles (L) to door panel 10 (both
L&R ) with 2 x bolts (K) and tighten.
3. Attach 2 x rubber pad (G)to door panel 10 (both
L
&
R
)
.
1. Attach the door panel 10 (both L&R) to the
assembled unit with 8 x screws (J) and tighten.
Note: The gaps between the door and frame can
be changed by making adjustments to the hinges
with a screwdriver. Refer to adjustment diagrams.
Laterally (Side to Side)
Front to back
Vertically ( up and down)
1. Insert 4 x cambolts (A) into drawer front panel
11.
2. Attach drawer side panel 13 (both L&R) to
drawer front panel 11.
3.Insert 4 x camlocks (N) to drawer side panel 13
(both L&R). Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
4. Insert drawer bottom panel 8 into the groove of
the drawer side panels 13 (both L&R).
5. Attach drawer back panel 12 to the assembled
unit with 4 x scrwes (F) and tighten.
6. Attach 1 x handle (M) to the drawer front panel
11 with 2 x bolts (K) and tighten.
STEP SEVEN
STEP SIX
STEP EIGHT
Page4of6

1. Insert the drawer into the unit.
1. Use pencil to mark through predrilled hole on
back panel.
1. Use power tool drill through the pencil mark.
STEP TWELVE
STEP TEN
STEP NINE
Page5of6

1. Attach the assembled unit to the wall with 2 x
screws
,
ti
g
hten with a screwdriver.
Warning: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
p
i
pes
.
NB: Wall fixings are not incuded, please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP THIRTEEN
Page6of6