NIIMBOT B18 User manual

APP connectionAPP download
Search for "NIIMBOT" on the Google play or Apple store,
download and install the APP.
1
2For more functions used in home application, our APP "NIIM" is
recommended to download and install.
02.How to download the APP
Please check the APP for more instructions.
Open the NIIMBOT APP Help CenterHardware InstructionsMe
Quick installation
01.Label installation
buckle
Please select thermal transfer label paper
compatible with the B18 printer.
Insert a label roll with the chip facing up.
Invalid if torn
This side up
Align and pull gently the label paper out of the
guide slot until the split after the first label.
Tighten the tape counterclockwise as indicated, then load
the chip face down in the card slot.
Pull the buckle up to open the cover.
This side down
T
h
i
s
s
i
d
e
d
o
w
n
C
o
n
t
r
a
r
o
t
a
t
e
t
o
t
i
g
h
t
e
n
Ribbon mark
Close and buckle the cover.
Design & Print APP
easy to download and use
NIIM
Design & Print APP
easy to download and use
NIIMBOT
1 × B18 Label Printer
1 × USB TYPE-C Data Cable
1 × Label paper
1 × Ribbon
1 × Quick-Reference Guide
Packing List
03.How to connect via Bluetooth
The illustrations of the product, accessories, software interface, etc.
in this Getting Started Guide are schematic diagrams and are for
reference only. Due to product updates and upgrades, the actual
product may be slightly different from the schematic diagram.
Please refer to the actual product. Reserve the right to improve the
technology of product without piror notice.
Special Note
Open the "NIIMBOT" APP first, then turn on the Bluetooth
of cellphone.
Click on the APP homepage to connect to the label printer
and select the corresponding device model,
After the connection is successful, click "Current Label Template"
on the home page to enter the editing page.
3
Note: Generally, the PIN code is 0000 or 1234. Enter the
PIN code and press "OK".
8:30
NIMBOT Turn on bluetooth
2
4
3
5
Split
Guide slot

Warning and Attention
Please read these warnings carefully before use to avoid
damage and accidents.
Do not wipe the device with
corrosive chemicals or detergents
Do not operate the device near
any place with flammable
materials such as gas stations
and fuel warehouses
Please keep the device and accessories safe and out of reach of
children to avoid risks.
If any water makes contact with the device, please turn it off immediately.
Please turn off the device immediately in case of any fault in operation.
Do not touch the print head after prolonged and continuous printing to
avoid scalding due to high temperature.
Attention
When the printer is running, do not open the paper bin cover.
When charging, keep the printer and power adapter at room
temperature with good ventilation.
Excessively high or low temperature may damage print quality.
If the printer is stored for a long period of time, please recharge it
every three months.If it is not recharged, the battery may fail or
even leak liquid, damaging the printer.
If the battery fails to meet the performance requirements, please
stop using it immediately and contact the customer service center
for processing.
Please use NIIMBOT label paper to avoid poor printing quality or
even damage to the print head.
In case of any problem during operation, please feel free to contact
the dealer or customer service center. NIIMBOT aims to provide the
best after-sales services for customers all over the world!
1.
2.
3.
4.
5.
6.
7.
Related statements
Quick-Reference Guide
Label Printer
B18
Basic usage
Product name Label Printer
Product size 135*90*37mm
Charging time 3 - 4 hours
Battery capacity 1200mAh
Printing accuracy 203dpi
Product weight
Connection mode
Output power
Bluetooth
Product number NIIMBOT B18
Rated output 5V/1A
Printing mode Thermal transfer
Print width 12mm
Charging method Type-C
Operating temperature 5°C-45°C
308g
-2.782dBm
Product Parameters
Support Email : [email protected]
Official Website : www.niimbot.net
Wuhan Jingchen Intelligent ldentificationTechnology Co., Ltd.
Production Address : No. 1, Tianyang Road, Chuanlong Avenue, Hengdian
Street, Huangpi District, Wuhan City, Hubei Province
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.The device can be
used in portable exposure condition without restriction.
Declaration of conformity
Hereby, Wuhan Jingchen Intelligent Identifification Technology Co., Ltd. declares that this
device is in compliance with the essential requirements and other relevant provisions of Radio
Equipment Directive (RED) 2014/53/EU. This product can be used across EU member states. This
device can be used in European Union.
Hereby, [Wuhan Jingchen Intelligent Identifification Technology Co., Ltd.] declares that the
radio equipment type [NIIMBOT B18] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address:http://www.niimbot.com.
Do not disassemble this
device by yourself
Features Order
On
Off
Print history
Press and hold the "On/Off" button for three seconds
Press and hold the "On/Off" button while power on state
Click the "On/Off" button once while power on state
Self-test page Double-click the "power button" while power on state
Basic Operation
Indicator
Blue
Blue
Blue
Red
Slow flash
Fast flash
On
Fast flash
On
Slow flash
Status
Standby
Charging
Bluetooth connected
Low battery standby
Description
Indicator
Red
Red
Low battery charging
Low battery bluetooth connected
NIIMBOT is a brand under Wuhan Jingchen Intelligent ldentication Technology Ltd.
© 2022 NIIMBOT. All rights reseed.

APP connection
Warning and Attention
Please read these warnings carefully before use to avoid
damage and accidents.
Do not wipe the device with
corrosive chemicals or detergents
Do not operate the device near
any place with flammable
materials such as gas stations
and fuel warehouses
Please keep the device and accessories safe and out of reach of
children to avoid risks.
If any water makes contact with the device, please turn it off immediately.
Please turn off the device immediately in case of any fault in operation.
Do not touch the print head after prolonged and continuous printing to
avoid scalding due to high temperature.
Attention
When the printer is running, do not open the paper bin cover.
When charging, keep the printer and power adapter at room
temperature with good ventilation.
Excessively high or low temperature may damage print quality.
If the printer is stored for a long period of time, please recharge it
every three months.If it is not recharged, the battery may fail or
even leak liquid, damaging the printer.
If the battery fails to meet the performance requirements, please
stop using it immediately and contact the customer service center
for processing.
Please use NIIMBOT label paper to avoid poor printing quality or
even damage to the print head.
In case of any problem during operation, please feel free to contact
the dealer or customer service center. NIIMBOT aims to provide the
best after-sales services for customers all over the world!
1.
2.
3.
4.
5.
6.
7.
Related statements
APP download
Search for "NIIMBOT" on the Google play or Apple store,
download and install the APP.
1
2For more functions used in home application, our APP "NIIM" is
recommended to download and install.
02.How to download the APP
Please check the APP for more instructions.
Open the NIIMBOT APP Help CenterHardware InstructionsMe
Quick-Reference Guide
Label Printer
B18
Quick installation
01.Label installation
buckle
Please select thermal transfer label paper
compatible with the B18 printer.
Insert a label roll with the chip facing up.
Invalid if torn
This side up
Align and pull gently the label paper out of the
guide slot until the split after the first label.
Tighten the tape counterclockwise as indicated, then load
the chip face down in the card slot.
Pull the buckle up to open the cover.
This side down
T
h
i
s
s
i
d
e
d
o
w
n
C
o
n
t
r
a
r
o
t
a
t
e
t
o
t
i
g
h
t
e
n
Ribbon mark
Close and buckle the cover.
Basic usage
Product name Label Printer
Product size 135*90*37mm
Charging time 3 - 4 hours
Battery capacity 1200mAh
Printing accuracy 203dpi
Product weight
Connection mode
Output power
Bluetooth
Product number NIIMBOT B18
Rated output 5V/1A
Printing mode Thermal transfer
Print width 12mm
Charging method Type-C
Operating temperature 5°C-45°C
308g
-2.782dBm
Product Parameters
NIIMBOT B18-英文版
Support Email : [email protected]
Official Website : www.niimbot.net
Wuhan Jingchen Intelligent ldentificationTechnology Co., Ltd.
Production Address : No. 1, Tianyang Road, Chuanlong Avenue, Hengdian
Street, Huangpi District, Wuhan City, Hubei Province
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.The device can be
used in portable exposure condition without restriction.
Declaration of conformity
Hereby, Wuhan Jingchen Intelligent Identifification Technology Co., Ltd. declares that this
device is in compliance with the essential requirements and other relevant provisions of Radio
Equipment Directive (RED) 2014/53/EU. This product can be used across EU member states. This
device can be used in European Union.
Hereby, [Wuhan Jingchen Intelligent Identifification Technology Co., Ltd.] declares that the
radio equipment type [NIIMBOT B18] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address:http://www.niimbot.com.
Do not disassemble this
device by yourself
Design & Print APP
easy to download and use
NIIM
Design & Print APP
easy to download and use
NIIMBOT
1 × B18 Label Printer
1 × USB TYPE-C Data Cable
1 × Label paper
1 × Ribbon
1 × Quick-Reference Guide
Packing List
03.How to connect via Bluetooth
The illustrations of the product, accessories, software interface, etc.
in this Getting Started Guide are schematic diagrams and are for
reference only. Due to product updates and upgrades, the actual
product may be slightly different from the schematic diagram.
Please refer to the actual product. Reserve the right to improve the
technology of product without piror notice.
Special Note
Open the "NIIMBOT" APP first, then turn on the Bluetooth
of cellphone.
Click on the APP homepage to connect to the label printer
and select the corresponding device model,
After the connection is successful, click "Current Label Template"
on the home page to enter the editing page.
3
Note: Generally, the PIN code is 0000 or 1234. Enter the
PIN code and press "OK".
8:30
NIMBOT Turn on bluetooth
Features Order
On
Off
Print history
Press and hold the "On/Off" button for three seconds
Press and hold the "On/Off" button while power on state
Click the "On/Off" button once while power on state
Self-test page Double-click the "power button" while power on state
Basic Operation
Indicator
Blue
Blue
Blue
Red
Slow flash
Fast flash
On
Fast flash
On
Slow flash
Status
Standby
Charging
Bluetooth connected
Low battery standby
Description
Indicator
Red
Red
Low battery charging
Low battery bluetooth connected
NIIMBOT is a brand under Wuhan Jingchen Intelligent ldentication Technology Ltd.
© 2022 NIIMBOT. All rights reseed.
2
4
3
5
Split
Guide slot
110mm
70mm
280mm