Nikon NIKKOR Z 14-24mm f/2.8 S User manual

En
User’s Manual
Fr
Manuel d’utilisation
Es
Manual del usuario
NIKKOR Z 14-24mm f/2.8 S
Printed in Thailand
7MMA3364-02 UPrinted in Thailand 7MMA4030-01

En
User’s Manual
Before using this product, please read these instructions carefully. You will also need to
consult the camera manual.
• This lens is intended exclusively for use with mirrorless cameras featuring a Nikon Z mount.
• Update the camera firmware to the latest version. With earlier versions, the camera
may fail to detect the lens correctly and some features may not be available. The latest
version of the camera firmware can be downloaded from the Nikon Download Center
at the URL below.
https://downloadcenter.nikonimglib.com/
For Your Safety
For Your Safety
To prevent damage to property or injury to yourself or to others, read“For Your Safety”
in its entirety before using this product.
Keep these safety instructions where all those who use this product will read them.
AWARNING: Failure to observe the precautions marked with this icon could
result in death or severe injury.
ACAUTION: Failure to observe the precautions marked with this icon could
result in injury or property damage.
A
A
WARNING
WARNING
•
•
Do not disassemble or modify this product.
Do not disassemble or modify this product.
Do not touch internal parts that become exposed as the result of a fall or
Do not touch internal parts that become exposed as the result of a fall or
other accident.
other accident.
Failure to observe these precautions could result in electric shock or other injury.
•
•
Should you notice any abnormalities such as the product producing smoke,
Should you notice any abnormalities such as the product producing smoke,
heat, or unusual odors,immediately disconnect the camerapower source.
heat, or unusual odors, immediately disconnect the camera power source.
Continued operation could result in fire, burns or other injury.
•
•
Keep dry.
Keep dry.
Do not handle with wet hands.
Do not handle with wet hands.
Failure to observe these precautions could result in fire or electric shock.
•
•
Do not use this product in the presence of flammable dust or gas such as
Do not use this product in the presence of flammable dust or gas such as
propane, gasoline or aerosols.
propane, gasoline or aerosols.
Failure to observe this precaution could result in explosion or fire.
•
•
Do not directly view the sun or other bright light source through the lens.
Do not directly view the sun or other bright light source through the lens.
Failure to observe this precaution could result in visual impairment.
•
•
Keep this product out of reach of children.
Keep this product out of reach of children.
Failure to observe this precaution could result in injury or product malfunction. In
addition, note that small parts constitute a choking hazard. Should a child swallow
any part of this product, seek immediate medical attention.
•
•
Do not handle with barehands in locations exposed toextremely high or
Do not handle with bare hands in locations exposed to extremely high or
low temperatures.
low temperatures.
Failure to observe this precaution could result in burns or frostbite.
A
A
CAUTION
CAUTION
•
•
Do not leave the lens pointed atthe sun or other strong light sources.
Do not leave the lens pointed at the sun or other strong light sources.
Light focused by the lens could cause fire or damage to product’s internal parts.
When shooting backlit subjects, keep the sun well out of the frame. Sunlight
focused into the camera when the sun is close to the frame could cause fire.
•
•
Do not leave the product where it will be exposed toextremely high
Do not leave the product where it will be exposed to extremely high
temperatures, for an extended period such as in an enclosed automobile
temperatures, for an extended period such as in an enclosed automobile
or in direct sunlight.
or in direct sunlight.
Failure to observe this precaution could result in fire or product malfunction.
•
•
Do not transport cameras or lenses with tripods or similar accessories
Do not transport cameras or lenses with tripods or similar accessories
attached.
attached.
Failure to observe this precaution could result in injury or product malfunction.
Notices for Customers in the U.S.A.
Notices for Customers in the U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Federal Communications Commission (FCC) Radio Frequency Interference
Federal Communications Commission (FCC) Radio Frequency Interference
Statement
Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
CAUTIONS
CAUTIONS
Modications
The FCC requires the user to be notified that any changes or modifications made to
this device that are not expressly approved by Nikon Corporation may void the user’s
authority to operate the equipment.
Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: [phone]
Notice for Customers in Canada
Notice for Customers in Canada
CAN ICES-3 B / NMB-3 B
Using the Lens
Using the Lens
Parts of the Lens: Names and Functions (Figure 1)
Parts of the Lens: Names and Functions (Figure 1)
Refer to the diagram on the left edge of this sheet.
qLens hood mounting
mark Use when attaching the lens hood. See E
wFocus ring
Use for manual focus.
• When focusing using autofocus, you can ad-
just focus manually by rotating the ring while
the shutter-release button is pressed halfway;
after focusing, press the shutter-release button
the rest of the way down to shoot.
—
eZoom ring Rotate to zoom in or out. —
rFocal length scale Determine the approximate focal length when
zooming the lens in or out. —
tFocal length mark
yLens info panel View focus distance, depth of field, and other
information.
See C,
D
uControl ring
Rotate to adjust a setting such as [Aperture] or
[Exposure compensation] assigned using the
camera. For more information, see the descrip-
tion of [Custom control assignment], [Custom
controls], or [Custom controls (shooting)] in the
camera manual.
—
iDisplay button Save settings or choose the information shown
in the lens info panel.
See C,
D
oL-Fn button
Press to perform a function assigned using the
camera. For more information, see the descrip-
tion of [Custom control assignment], [Custom
controls], or [Custom controls (shooting)] in the
camera manual.
—
!0
Focus-mode switch
Choose a focus mode.
• A: Autofocus
• M: Manual focus
Note that regardless of the setting chosen, focus
must be adjusted manually when manual focus
mode is selected using camera controls.
—
!1 Lens mounting mark Use when mounting the lens on the camera. See A
!2 Rubber lens-mount
gasket ——
!3 CPU contacts Used to transfer data to and from the camera. —
!4 Filter slot
For use with trimmable third-party filter sheets.
See F
!5 Lens cap (rear cap) Use to protect the rear lens element. —
!6
LC-Z1424 and
LC-K104 lens caps
(front caps)
Use to protect the front lens element.
• The LC-K104 is for use with the HB-97 lens hood. See B
!7 HB-96/HB-97
lens hood
Lens hoods block stray light that would other-
wise cause flare or ghosting. They also serve to
protect the lens.
• The HB-97 is for use with Nikon screw-on filters.
See E
!8 Lens hood lock
release button Use when removing the lens hood.
!9 Lens hood lock mark
Use when attaching the lens hood.
@0 Lens hood alignment
mark
A
Attachment and Removal
Attachment and Removal
Attaching the Lens
z
Turn the camera o, remove the body cap, and detach the rear lens cap.
xPosition the lens on the camera body, keeping the mounting mark
on the lens aligned with the mounting mark on the camera body,
and then rotate the lens counterclockwise until it clicks into place.
Removing the Lens
zTurn the camera o.
x
Press and hold the lens release button while turning the lens clockwise.
B
Attaching and Removing the Front Lens Cap (Figure 2)
Attaching and Removing the Front Lens Cap (Figure 2)
Attaching the Front Lens Cap
Keeping the latches squeezed together (q) and the top of the cap aligned with
the lens hood mounting mark, attach the caps in the orientations shown (w).
Removing the Front Lens Cap
Keeping the latches squeezed together (q), remove the lens caps as shown (w).
C
The Lens Info Panel
The Lens Info Panel
The lens Info panel lights when the lens is attached to a camera and the camera is on.
• Press the lens display button to cycle the display as shown:
Depth of field 1
Aperture 2Focal length
Focus distance
1 Depth of field is displayed when the camera is in mode Aor M.
2 Aperture is displayed only when the cam-
era is in mode Aor M. The display for other
modes is shown in the illustration.
• The focus mode (AF or MF) is briefly displayed when chosen using the focus-
mode switch.
• The panel turns off automatically when the camera standby timer expires or if
no lens operations are performed for about 10 seconds. Press the display button
to reactivate the display.
A The Lens Info Panel
The focus distance, depth of field, and other information displayed in the lens Info panel are approxima-
tions only.
D
Panel Options
Panel Options
Follow the steps below to choose the units for focus distance from meters (m) or
feet (ft) or adjust the brightness of the lens Info panel.
zPress and hold the display button to view settings.
• Unit or brightness selection options will be displayed. The currently select-
ed item will flash.
• Press the display button to toggle between displays.
Units Brightness
xChoose a setting using the lens control ring.
Units
-Rotate the control ring to choose from me-
ters (m) or feet (ft).
Brightness
-Rotate the control ring in the “+” (brighter)
or“−” (darker) direction.
-Choose from 6 levels of brightness.
-To turn the lens info panel off, rotate the
ring in the “−” direction until the icon
changes to .
• Press the display button to save changes and toggle the display.
• If no operations are performed using lens controls for about 5 seconds,
panel options will clear from the display. Any changes will be lost.
cPress and hold the display button to return to the lens information display.
• Choosing for brightness turns the lens info panel off.To turn the display
on again, press and hold the display button.
E
Attaching and Removing the Lens Hood
Attaching and Removing the Lens Hood
Attaching the Lens Hood (Figure 3)
• qAlign the lens hood mounting mark (
● ) with the lens hood alignment mark
(
● ) and wrotate the lens hood in the direction shown until ethe mounting
mark (
● ) is aligned with the lens hood lock mark ( ).
• Gripping the front too tightly makes the lens hood difficult to attach or remove. When
rotating the lens hood, hold it near the lens hood alignment mark (●) on its base.
• The lens hood can be reversed and mounted on the lens when not in use. Before re-
versing the HB-97, be sure to remove any Nikon screw-on filters that may be attached.
Removing the Lens Hood (Figure 4)
• Keeping the lens hood lock release button pressed (q), rotate the lens hood in
the direction shown (w) and remove it from the lens (e).
• T
he same procedure can be used when the lens hood is reversed.
F
Using Filters
Using Filters
Filters can be attached to the lens at the front and rear. Nikon 112 mm screw-on
filters can be used at the front of the lens and third-party trimmable filter sheets at
the rear. These can be attached as follows:
Nikon Screw-on Filters
Nikon screw-on filters can be attached to the HB-97 lens hood (Figure 5).
• Use only one Nikon screw-on filter at a time.
DScrew-on Filters
Shadows may appear at the periphery of pictures taken with third-party screw-on
filters.
Filter Sheets
The rear mount opening has a filter slot. Cut third-party trimmable filter sheets to
the size shown in Figure 6 and insert them in the filter slot (Figure 7).
When the Lens Is Attached
When the Lens Is Attached
The focus position may change if you turn the camera off and then on again after fo-
cusing. If you have focused on a pre-selected location while waiting for your subject to
appear, we recommend that you do not turn the camera off until the picture is taken.
Cameras with AF-Assist Illuminators
Cameras with AF-Assist Illuminators
The lens or lens hood may block the light from the camera AF-assist illuminator.
• For the latest information on using the lens with cameras that have built-in AF-assist
illuminators, visit the site below.
https://downloadcenter.nikonimglib.com/
Using the Lens on Cameras with a Built-in Flash
Using the Lens on Cameras with a Built-in Flash
Shadows will be visible in photos where light from the built-in flash is obscured by the
lens or lens hood. Remove the lens hood before shooting. Note, however, that depend-
ing on lens focal length and the distance to the subject, shadows may appear even
when the lens hood is removed.
• Shadows will be visible in photos taken when this lens is mounted on a Z 50.
• For the latest information on focal lengths and subject distances at which shadows
will not appear in photos taken with a built-in flash, visit the site below.
https://downloadcenter.nikonimglib.com/
Precautions for Use
Precautions for Use
• Do not pick up or hold the lens or camera using only the lens caps or lens hood.
• Keep the CPU contacts clean.
• Should the rubber lens-mount gasket be damaged, cease use immediately and take
the lens to a Nikon-authorized service center for repair.
• Replace the lens caps when the lens is not in use.
• Do not leave the lens in humid locations or in locations in which it may be exposed to
moisture. Rusting of the internal mechanism can cause irreparable damage.
• Do not leave the lens next to open flames or in other extremely hot locations. Ex-
treme heat could damage or warp the reinforced plastic exterior.
• Rapid changes in temperature may cause damaging condensation inside and outside
the lens. Before taking the lens from a warm to a cold environment or vice versa, place
it in a bag or plastic case to slow the change in temperature.
• We recommend that you place the lens in its case to protect it from scratches during transport.
Lens Care
Lens Care
• Removing dust is normally sufficient to clean the glass surfaces of the lens.
• The uorine-coated front lens element can be cleaned as described below.
-Smudges, fingerprints, and other oily stains can be removed using a soft, clean cotton cloth
or third-party lens cleaning tissue; clean from the center outwards using a circular motion.
-To remove stubborn stains, wipe gently using a soft cloth lightly dampened with a
small amount of distilled water, ethanol, or lens cleaner.
-Any drop-shaped marks left from this process on the water- and oil-repellent sur-
face can subsequently be removed with a dry cloth.
• When cleaning the rear lens element, which is not uorine-coated, remove smudges, fingerprints,
and other oily stains using a soft, clean cotton cloth or third-party lens cleaning tissue
lightly dampened with a small amount of ethanol or third-party lens cleaner. Wipe
gently from the center outwards in a circular motion, taking care not to leave smears
or touch the lens with your fingers.
• Never use organic solvents such as paint thinner or benzene to clean the lens.
• Nikon Neutral Color (NC) filters and the like can be used to protect the front lens element.
• Do not store with naphtha or camphor moth balls or in direct sunlight. If the lens will not
be used for an extended period, store it in a cool, dry location to prevent mold and rust.
Accessories
Accessories
Supplied Accessories
Supplied Accessories
• LC-Z1424 Lens Cap (front cap)
• LC-K104 Lens Cap (front cap)
• LF-N1 Lens Cap (rear cap)
• HB-96 Lens Hood
• HB-97 Lens Hood
• CL-C2 Lens Case
DUsing the Lens Case
• The case is intended to protect the lens from scratches, not from falls or other physical shocks.
• The case is not water resistant.
• The material used in the case may fade, bleed, stretch, shrink, or change color when rubbed or wet.
• Remove dust with a soft brush.
• Water and stains can be removed from the surface with a soft, dry cloth. Do not use alcohol, benzene, thinner,
or other volatile chemicals.
• Do not store in locations exposed to direct sunlight or high temperatures or humidity.
• Do not use the case to clean the monitor or lens elements.
• Be careful that the lens does not fall from the case during transport.
Material: Polyester
Compatible Accessories
Compatible Accessories
• Nikon 112 mm screw-on filters (must be attached to the HB-97 lens hood)
• Trimmable filter sheets
Specications
Specications
Mount
Mount Nikon Z mount
Focal length
Focal length 14 – 24 mm
Maximum
Maximum
aperture
aperture
f/2.8
Lens construction
Lens construction 16 elements in 11 groups (including 4 ED elements, 3 aspherical elements, ele-
ments with Nano Crystal and ARNEO coats, and a fluorine-coated front lens element)
Angle of view
Angle of view • FX format: 114°–84°
• DX format: 90°–61°
Focal length scale
Focal length scale Graduated in millimeters (14, 15, 16, 18, 20, 24)
Focusing system
Focusing system Internal focusing system
Minimum focus
Minimum focus
distance
distance 0.28 m (0.92 ft) from focal plane at all zoom positions
Maximum repro-
Maximum repro-
duction ratio
duction ratio 0.13× (24 mm focal length)
Diaphragm
Diaphragm
blades
blades 9 (rounded diaphragm opening)
Aperture range
Aperture range f/2.8 – 22
Filter slot
Filter slot Located at rear of lens
Dimensions
Dimensions Approx. 88.5 mm/3.5 in. maximum diameter × 124.5 mm/5 in.
(distance to end of lens from camera lens mount flange)
Weight
Weight Approx. 650 g (1 lb 7 oz)
Nikon reserves the right to change the appearance, specifications, and performance of this
product at any time and without prior notice.

Nikon
Reta in thi s Internationa l Wa rranty with proof of purchase (bill of sale) for your records
Nikon Corp. LENS ONE YEAR WORLDWIDE LIMITED WARRANTY
(Excluding the Continental United States, Alaska, Hawaii, Puerto Rico, and U.S. Virgin Islands)
Welcome to the worldwide family of Nikon owners.
Your Nikon equipment has been manufactured to the highest quality standards by NIKON CORPORATION, Tokyo, Japan. This
limited warranty entitles the original consumer purchaser to international warranty protection in accordance with these terms
and conditions. It affords the original consumer purchaser warranty protection outside the Con t inental United States, Al a ska,
Hawaii, Puerto Rico and the U.S. Virgin Islands. Such warranty coverage is supplemental to and not in lieu of the Unit ed States
Nikon Inc. Lens One Year USA Limited Warranty which is received by the origina l consumer purchaser with the Nikon produ ct .
T
he Nikon product except for batteries is warranted by NIKON CORPORAT I ON, Tokyo, Japan to be free from d efects in m at eri a ls
or workmanship for a period of one (1 )year from the date of purchase. To find an international Nikon S ervice F acility
see: http://imaging.nikon.com/products/imaging/worldwide/index.htm. During this period any one of the int e rn a tional service
facilities will service without charge any parts or assembly of parts found to be defective in materials or workmanship, subj e ct
to the following limitations and exclusions:
1. This warranty extends to the original consumer purchaser only and is not assignable or transferable.
2. This warranty shall not ex t end to any product which has been subject to misuse, alteration, abuse, negligence, acci d ent or
unauthorized repair or has had its serial number altered or removed.
The above warranty is expressly in lieu of all other warranties expressed or implied including but not limited
to any implied warranty of merchantability or fitness for particular purpose, except to the extent prohibited
by applicable law, in which event the duration of any implied warranty shall be limited to one (1) year from
the date of purchase or such longer period as may be required by applicable law. Under no circumstances
shall Nikon be liable for consequential, indirect, special, direct, exemplary, punitive or incidental damages
arising out of or related to any breach of this warranty or any other claim regarding this product, including
but not limited to, claims of negligence, strict liability or breach of contract.
Some jurisdictions, such as states or provinces, do not allow (a) limitations on how long an implied warranty
lasts or (b) the exclusion or limitation of incidental or consequential damages so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary from jurisdiction to jurisdiction.
In order to obtain in t ernational service, the original consumer purchaser should return the Nikon product, e ither in person or
addressed to the Warranty Department of any authorized service facility listed on the above website, together with p roof of
purchase and proof of purchase date (bill of sale) and this warranty. The original consumer purchaser in return i ng this p ro duct
must pr epay all shipping and insurance costs to the service facility.