Nikon AF-S VR DX Zoom Nikkor 18-200/3.5-5.6G ED Operating instructions

作成承認印 配布許可印
JAA79471-R.3678.A
Copyrigh ｃ2005 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず !!
Printed in Japan Dec 2005
AF-S VR DX Zoom Nikkor
18-200/3.5-5.6G ED
JAA79451
JAA79471
(MADE IN THAILAND)
(MADE IN JAPAN)
REPAIR MANUAL
INC

JAA79471-R.3678.A
- M1 ･AF-S VRDX 18-200/3.5-5.6G -
Specications
Type of lens: G-type AF-S DX VR Zoom-Nikkor lens having built-in CPU and Nikon
bayonet mount [Specially designed for use with the Nikon digital SLR cameras
(Nikon DX format)]
Focal length: 18mm–200mm
Maximum aperture: f/3.5–5.6
Lens construction: 16 elements in 12 groups (3 aspherical lens and 2 ED lens elements)
Picture angle: 76°– 8°
Focal length scale: 18, 24, 35, 50, 70, 135, 200mm
Distance information: Output to camera body
Zoom control: Manually via separate zoom ring
Focusing: Nikon Internal Focusing (IF) system (utilizing an internal Silent
Wave Motor); manually via separate focus ring
Vibration reduction: Lens-shift method using voice coil motors (VCMs)
Shooting distance scale: Graduated in meters and feet from 0.5m (3 ft.) to innity ( ‡)
Closest focus distance: 0.5m (1.6 ft.) at all zoom settings
No. of diaphragm blades: 7 pcs. (rounded)
Diaphragm: Fully automatic
Aperture range: f/3.5 to f/22 (at 18mm), f/5.6 to f/36 (at 200mm)
Exposure measurement: Via full-aperture method
Attachment size: 72mm (P = 0.75mm)
Dimensions: Approx. 77mm dia. x 96.5mm extension from the camera’s lens mount ange
Weight: Approx. 560g (19.8 oz)
INC

JAA79471-R.3678.A
- D1･ AF-S VRDX18-200/3.5-5.6G -
On this lens, the VR (vibration-reduction) unit is mounted to correct the picture blur.
In order to maintain the functional accuracy of the picture blur correction, if detaching the VR
(vibration-reduction) unit and gyro base plate or if removing the main PCB unit, be sure to adjust the VR by
using the VR lens adjustment equipment (J15380）.
However, if disassembling the parts except the above, the VR adjustment is NOT necessary.
At service agencies where the "VR lens adjustment equipment" is not prepared, do NEITHER disassemble
NOR repair the products of the above case.
Caution:
① When disassembling, make sure to memorize the processing state of wires, screws to be xed and their types, etc.
②Because prototypes are used for "Disassembly/(Re)assembly/Adjustment", they may differ from the actual
products in forms, etc.
③ Because pictures are processed by a special method, they may differ from the actual ones in texture.
・Lead-free solder is used for this product.
・For soldering work, the special solder and soldering iron are required.
・Do NOT mix up lead-free solder with traditional solder.
・Use the special soldering iron respectively for lead-free solder and lead solder.
They cannot be used in common.
Points to notice for Lead-free solder products
※ Before Disassembly / (Re)assembly / Adjustment
INC

JAA79471-R.3678.A
- D2･ AF-S VRDX18-200/3.5-5.6G -
Retaining ring (#42) 1st lens group (B0006)
1. Disassembly
1st lens group
1st lens-group cover ring
(#60)
Cover ring (#62)
#60
Filter ring
#62
#128×6
Filter ring
#100
G1-2 cemented lens
#133
INC

JAA79471-R.3678.A
- D3･ AF-S VRDX18-200/3.5-5.6G -
Index
Index
2nd lens group
① Set the lens zoom position to 18 , while the focus ring to "∞" position.
② Mount the 2nd lens-group retaining tool ( J11318) on the lens by aligning the indexes with each other.
③ Remove the 2nd lens-group and the washer (#80) by using the wrench ( J11317).
J11317
Washer (#80A ～K)
2nd lens group
★
★
New Tool
★
★
★
Groove×3
Hole×2
Enter the three convex portions of (J11318) into the three
grooves of (J11318), while two pins into the two holes of the
lens.
Caution) If the positions of pins do not match, turn the
focus ring little by little, then align the pins with the holes.
J11318
Convex portion×3
2nd lens-G retaining
tool (J11318)
Pin×2
INC