Nikon Callaway iQ User manual

Instruction manual /Manuel d’utilisation
Manual de instrucciones / Manual de instruções
Callaway iQ
Laser Rangefinder / Télémètre laser
Telémetro láser / Telêmetro a Laser
En Fr
Es Pt

2 3
English................................p. 4-p. 21
Français ...........................p. 22-p. 39
Español.............................p. 40-p. 57
Português brasileiro........p. 58-p. 75

En
Fr
Es
Pt
4 5
En
Fr
Es
Pt
CONTENTS
Cautions before use ................................................................... 5-7
Key features ................................................................................... 8-9
Nomenclature/Composition ..................................................... 10
Changing batteries ....................................................................... 11
Internal display......................................................................... 12-13
Operational summary............................................................ 13-16
Specifications............................................................................ 17-18
Others................................................................................................. 19
Troubleshooting/Repair........................................................ 20-21
English
Cautions before use
Thank you for purchasing the Nikon Callaway iQ.
This high-spec laser rangefinder features an angle compensation function in addition to the existing
linear distance measurement function for enhanced enjoyment of sports and other outdoor applications.
Please observe the following guidelines strictly so you can use the equipment properly and avoid
potentially hazardous problems. Before using this product, read thoroughly the“SAFETY PRECAUTIONS”
and instructions on correct usage accompanying the product.
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
Keep this manual within reach for easy reference.
• Specificationsanddesignaresubjecttochangewithoutnotice.
• Noreproductioninanyformofthismanual,inwholeorinpart(exceptforbriefquotationincritical
articles or reviews), may be made without written authorization from NIKON VISION CO., LTD.

En
Fr
Es
Pt
6 7
En
Fr
Es
Pt
Cautions before use
Please observe the following
guidelines strictly so you can use
the equipment properly and avoid
potentially hazardous problems.
Before using this product, read
thoroughly the“SAFETY AND
OPERATION PRECAUTIONS”and
instructions on correct usage
accompanying the product. Keep
this manual within reach for easy
reference.
WARNING
This indication alerts you to the fact
that any improper use ignoring the
contents described herein can result in
potential death or serious injury.
CAUTION
This indication alerts you to the fact
that any improper use ignoring the
contents described herein can result in
potential injury or material loss.
SAFETY AND OPERATION
PRECAUTIONS
Warning
• Neverlookdirectlyatthelaserbeam
or directly at the sun when using the
Nikon Callaway iQ.
• DonotdepressthePOWERbutton
while looking into the optics from the
objective side.
• Donotaimattheeye.
• Donotoperatetheunitwithother
additional optical elements, such as
lenses or binoculars. Using an optical
instrument together with the Nikon
Callaway iQ increases the danger of
damaging the eyes.
• DonotdisassembletheNikon
Callaway iQ. The emitting laser may
be harmful to your health. A product
that has been disassembled is not
guaranteed by the manufacturer.
• IftheNikonCallawayiQ’sbodycover
is damaged, or if it emits a strange
sound due to dropping or for some
other cause, immediately remove the
battery and stop using.
Cautions
• WhennotusingtheNikonCallawayiQ,
donotpushthePOWERbutton.
• DonotleavetheNikonCallawayiQ
within the reach of small children.
• Rain,water,sandandmudshouldbe
removed from the rangefinder body
surface as soon as possible, using a
soft, clean, dry cloth.
• AlthoughtheNikonCallawayiQis
waterproof, it is not designed for use
underwater.
• DonotswingtheNikonCallawayiQby
its strap. It may hit someone and cause
injury.
• DonotleavetheNikonCallawayiQ
in an unstable place, as it may fall
and cause injury, or damage the
equipment.
• DonotlookthroughtheNikon
Callaway iQ while walking. You may
walk into something and get hurt.
• DonotleavetheNikonCallawayiQin
a car on a hot or sunny day, or near
heat-generating equipment. This may
damage or negatively affect it.
• DonotleavetheNikonCallawayiQin
direct sunlight. Ultraviolet rays and
excessive heat may negatively affect
or even damage the unit.
• WhentheNikonCallawayiQis
exposed to sudden changes in
temperature, water condensation may
occur on lens surfaces. Do not use the
product until the condensation has
evaporated.
• Donotusealcoholforcleaningthe
main body.
• Donotleavethepolyethylenebag
used for packaging within the reach of
small children.
• Becarefulthatsmallchildrendonot
inadvertently swallow the eyecup.
If it does happen, consult a doctor
immediately.
• Ifyouusetherubbereyecupfora
long period of time, you may suffer
skin inflammation. If you develop
any symptoms, consult a doctor
immediately.
• WhencarryingtheNikonCallaway
iQ, store it in the soft case.
• IfyourNikonCallawayiQshouldfail
to operate correctly, discontinue
use immediately and consult the
Troubleshooting Table. If you are
unable to fix the problem, contact
your local dealer for instructions on
where to send it for repair.
NOTES ON LITHIUM BATTERY
If handled incorrectly, batteries may
rupture and leak, corroding
equipment and staining clothing. Be
sure to observe the following:
• Installbatterieswiththe+and–
poles positioned correctly.
• Batteriesshouldberemovedwhen
exhausted or during extended
periods of non-use.
• Alwaysusethesametypeofbattery.
• Ifbatteryfluidcontactseyesorskin,
rinse well with water. If swallowed,
consult a doctor immediately.
• Donotshort-circuitbatterychamber
terminals.
• Donotcarrybatteriestogetherwith
keys or coins in a pocket or bag. This
may overheat and short-circuit
batteries.
• Donotputbatteriesinfireorwater.
Never disassemble batteries.
• Donotchargebatteries.
• Donotsubjectstoredbatteriesto
extremes in temperature.
• Donotsubjectbatteriestostrong
vibrations or shock.
CARE AND MAINTENANCE
Lenses
• Whenremovingdustonthelens
surface, use a soft oil-free brush.
• Whenremovingstainsorsmudges
like fingerprints from the lens surface,
wipe the lenses very gently with a soft
clean cotton cloth or quality oil-free
lens tissue.
Use a small quantity of pure alcohol
(notdenatured)towipestubborn
smudges. Do not use velvet cloth or
ordinary tissue, as it may scratch the
lens surface. Once the cloth has been
used for cleaning the body, it should
not be used again for the lens surface.
Main body
• Cleanthebodysurfacewithasoft,
clean cloth and a dry cloth. Do not
use benzene, thinner, or other organic
agents because they may cause
discoloration or rubber degeneration.
Storage
• Watercondensationormoldmay
occur on the lens surface because of
high humidity. Therefore, store the
Nikon Callaway iQ in a cool, dry place.
After use on a rainy day or at night,
thoroughly dry it at room
temperature, then store in a cool, dry
place.

En
Fr
Es
Pt
8 9
En
Fr
Es
Pt
Key Features
• Lineardistancemeasurementrange:10-915meters/11-1,000
yards
• Distancemeasurementdisplaystep:
 LinearDistance(atupper7-segmentdisplay)
0.1 meter/yard
   (measurementdistanceislessthan999.9meters/
yards)
1.0 meter/yard
   (measurementdistanceis1,000meters/yardsor
further)
  SlopeAdjustedDistance(atlower7-segmentdisplay)
1.0 meter/yard
   (calculateddistanceislessthan999meters/yards)
• Easy-to-aim6xopticalobservationsystem
• Quantifiestheslopeadjusteddistancetohittheballinrelation
to the rangefinder's level by measuring linear distance and
angle.
• TheresultsaredisplayedonaninternalLCDpanel.
• ActiveBrightnessControlViewfinderdetectslightconditionsof
the ground area mainly in the view field and, when necessary,
automatically turns on the orange LED illumination.
The brightness of the orange illumination is adjusted
automatically according to the light conditions.
• Waterproofdesign(NOTdesignedforunderwaterusage)
• Invisible/EyesafeEN/IECClass1MLaser
• 8-secondresultsdisplay
• Compact,lightweight,ergonomicdesign
• Automaticshut-off(afterapprox.8sec.unattended)
• Defaultto“LastUse”settings
• Approx.5-secondcontinuousmeasuringfunction
The Nikon Callaway iQ emits invisible, eyesafe, infrared energy
pulses that reflect off the selected target back to its optical receiver.
Sophisticated precision charge circuitry is used to instantaneously
calculate distances, by measuring the time it takes for each pulse to
travel from the rangefinder to the target and back. Laser reflectivity
and measurement results may vary according to climatic and
environmental conditions, the colour, surface finish, size, shape and
other characteristics of the target.
The following factors ensure better range and accuracy:
• Nighttimeuse
• Cloudyweather
• Bright-colouredtargets
• Targetswithhighlyreflectivesurfaces
• Targetswithshinyexteriors
• Large-sizetargets
• Shootingtargetsfacingat90degrees
Measurementmayresultininaccuracyorfailureinthefollowingcases:
• Slenderorsmalltarget
• Targethasdiffusingreflectivesurface
• Targetdoesnotreflectthelaserbeamtotherangefinder(glass,mirror,etc.)
• Blacktarget
• Targethasvaryingdepths
• Insnow,rainorfog
• Targetmeasuredthroughglass
• Reflectivesurfacemeasuredfromdiagonaldirection
• Movingtarget
• Obstaclemovinginfrontofthetarget
• Whentargetingthesurfaceofwater

En
Fr
Es
Pt
10 11
En
Fr
Es
Pt
Nomenclature/Composition Changing Batteries
1Monocularobjectivelens/
Laser emission aperture
2Laser detector aperture
3MODEbutton
4POWERbutton
56x monocular eyepiece
6Eyecup/diopter adjustment ring
7Diopter index
8Strap eyelet
9Battery chamber cover
!pBattery chamber cover“Open/Close”
indication
!qProduct number/explanatory label
!w Laser warning label
Body ..............................................x1
Stay-oncase(CDE)...................x1
Lithiumbattery(CR2).............. x1
Composition
• Type of battery: 3V CR2 lithium battery
• Battery condition indicators
: Battery has enough power for use.
: Battery is getting low.
flashing: Battery is low and battery should be replaced.
disappears: Battery is exhausted and should be replaced.
Flashing mark in the LCD alerts that the battery should be replaced.
1Open the battery chamber cover
Using the ball of the thumb or a coin in the recessed part of the battery chamber cover, rotate the cover following the Open/
Close arrow indicator. It may not open easily due to its rubber packing for water resistance.
2Replace the old battery with a new one
 Installnewbatterywiththe[+]and[-]correctlypositionedfollowingthe“Batteryinstallation”indicationsealinthebattery
chamber.(Insertbatterypositioningthe[+]poletowardstheinsideofthechamber.)[TheNikonCallawayiQwillnotoperateif
thebatteryisinstalledincorrectly.]
3Close the battery chamber cover
Align the Open/Close indicator with the white dot and insert the battery chamber cover. Using the ball of the thumb or a coin,
turn the cover in the opposite direction to the arrow indicator. It may not close easily due to the rubber packing for water
resistance, but continue to turn it all the way until it stops. Confirm that the cover is securely closed.
• Battery life
Continuous operation: Approx.5,500times(at20°C)
This figure may differ according to temperature, and other factors such as target shape, color, etc.
* The Nikon Callaway iQ comes with a 3V CR2 lithium battery. However, due to natural electrical discharge, the life of the battery will likely be shorter
than that noted above.
* Replace battery if the Nikon Callaway iQ is ever submerged in water or if water enters the battery chamber.
7
5
!q
!p
8
9
6
!w
1
3
4
2

En
Fr
Es
Pt
12 13
En
Fr
Es
Pt
Internal display
1. 『 』- Target aiming/Laser irradiate system
『』- Aim at the target. Position the target at the center of the reticle.
『 』- Appears while the laser is being used for a measurement.
 (Remainspresentduringsinglemeasurement.Blinksduringcontinuousmeasurements.)
  Warning:Donotlookintotheobjectivelenseswhenthismarkisshown.
2．Upper display

Lower display
<Examples of measurement results>
Upper 4 digits: Linear distance
 Displayofresults:( ＜999.9 meters/yards) e.g. 234.9 meters =『』
 Displayofresults:( ≧1,000 meters/yards) e.g. 1,065 yards = 『』
Lower 3 digits: Slope adjusted distance
The results of "Horizontal distance ± Height"
Displayofresults:( ＜999 meters/yards) e.g. 235 meters = 『』
 Displayofresults:( ≧1,000 meters/yards) 『』
『』Now measuring
『』Failure to measure or unable to measure distance
3. 『』Display units
『』Indicates distance being measured in meters.
『 』Indicates distance being measured in yards.
4. 『 』Indicatesbatterycondition.(See"Changing Batteries")
5. Measurementresultsandsymbolsign
- Calculates linear distance to your target, and displays the result in the upper 4-digit 7-segment
display.
-Calculates the slope adjusted distance to your target by measuring linear distance and angle,
and displays the result in the lower 3-digit 7-segment display.
6.
Active Brightness Control Viewfinder
Active Brightness Control Viewfinder detects light conditions of
the ground area mainly in the view field and, when necessary,
automatically turns on the orange LED illumination.
The brightness of the orange illumination is adjusted
automatically according to the light conditions.
Although the LCD was produced using the most advanced
technology, it is impossible to eliminatedustcompletely.When
using this product, the LCD is magnified by high magnification
of the eyepiece lens and dust may appear as a defect. It will not,
however, affect measurement accuracy.
Upward Downward
Distance/measurement status display
Digitally indicates measured distance in meters/yards. Also indicates
measuringstatussuchas“Measurementinprogress”,“Measurement
unsuccessful”or“Unable to measure.”
Operational summary
Caution — use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure
1. Install a battery in the battery chamber. (See "Changing
Batteries")
2. Rubber eyepiece cup
Both eyeglass wearers and non-wearers can use this
rangefinder without attaching the rubber eyepiece cup.
3. Diopter adjustment
Adjust diopter to obtain a clear image in the LCD.
First, rotate the diopter adjustment ring counterclockwise until
it comes to a complete stop. Next, turn on the power to activate
the LCD when you look through the Nikon Callaway iQ. Rotate
the diopter adjustment ring clockwise until the display comes
into focus.
If the diopter is not adjusted to correspond to your eyesight,
you may not be able to aim your subject.

En
Fr
Es
Pt
14 15
En
Fr
Es
Pt
Operational summary
4. Measuring
 Note:DepressingandholdingdownthePOWERbuttoncausesall
symbols to be displayed in the internal LCD panel. After you
removeyourfingerfromthePOWERbutton,thelast-used
settingisdisplayed.(IfyoubrieflypressthePOWERbutton
then remove your finger, the LCD panel may display the last-
used setting without displaying all of the symbols. This is not a
malfunction or other problem.)
Before measuring, be sure to confirm unit setting.
◎: See the relevant mode section in this manual for setting.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by.
3. Press POWER button once to start single measurement.
Measuring.
4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops
Target focusing.
2. Aim at the target.
Positionthetargetatthecenterofthereticle
[Single measurement]
Failure to measure or
unable to measure distance.
Upward measurement. Downward measurement.
Displays the measured figure.
[Continuous measurement]
4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.
1.PressthePOWERbuttonforpower-on.(Powerturnsoff8
seconds after the last operation.)
Immediately after power-on.
(Initializing)
Stand-by.
2. Aim at the target.
Position the target at the center of the reticle
Target aiming
[Single measurement]
3.PressPOWERbuttononcetostartsinglemeasurement.
Measuring.
4. After measurement,“distance”or“fail to measure”indicator are
displayed for 8 seconds, then power turns off. If you press the
POWERbuttonduringpower-on(whiletheinternaldisplayislit),
another single measurement starts.
Failure to measure
or unable to
measure distance.
Upward
measurement.
Downward
measurement.
Displays the measured figure.
[Continuous measurement]
3.KeeppressingPOWERbuttontostartcontinuousmeasurementup
to approx. 5 seconds.The internal display shows“distance”and“fail to
measure”indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measurement stops.
Failure to measure or
unable to measure
distance.
Displays the measured
figure.(Target1)
Displays the measured
figure.(Target2)
4. After continuous measurement, the measured results are displayed for 8
seconds,thenpowerturnsoff.IfyoupressthePOWERbuttonduringpower-
on(whiletheinternaldisplayisactive),anothermeasurementstarts.
Blinks while performing measurements.
Whenmeasuringapinatagolfcourse,forexample,
use Continuous measurement mode for easy
measurement.Withnoobjectsbetweenyouand
the pin, the smallest number is the distance to your
targeted pin.

En
Fr
Es
Pt
16 17
En
Fr
Es
Pt
5. Selecting display unit mode(Factorydefaultsettingisyard.)
1. Confirm the LCD panel is on.
2. Press and hold the MODE button for approx. two seconds.
3.Whendisplayunithasswitched,releasetheMODE button.
4. After the unit is set, results will be converted and displayed in
the your selected measurement unit.
Meter[]
Yard []
6. Measurement results and Symbol sign
Upwardlook(+)angle
Up slope
Downwardlook(-)angle
Down slope
Upper 7-segment display Linear Distance
Lower 7-segment display Slope Adjusted Distance
Symbol sign
7. Distance display (NikonCallawayiQisFirstTargetPriority
Distance Display System.)
Whenobtainingdifferentresultsfromasinglemeasuring
operation, the Nikon Callaway iQ will display the distance to the
nearest target on the LCD panel.
ex.)Whenmeasuringatreestandinginfrontofahouse;
"115m"(distancetothetree)willbedisplayed.Thismodehas
application for golf.
8. Low battery indication
Flashing indicates that the battery power is low and
batteryshouldbereplaced.(See"ChangingBattery")
Tree Fence House
Distance to Target 115m 123m 128m
Operational summary Specifications
Measurementsystem
Detected inclination sign
Measuringrange Linear Distance: 10-915 meter/11-1,000 yards
Distance indication step Linear Distance: upper 4-digit 7-segment display
0.1meter/yards( ≦999.9m/yds.)
1.0meter/yards( ≧1,000m/yds.)
Slope Adjusted Distance: lower 3-digit 7-segment
1.0meter/yards( ≦999m/yds.)
"---"( ≧1,000m/yds.)
Accuracy Linear distance: ±1.0 meter/yard
Slope Adjusted distance: depends on actual distance and
angle.
Note: At distance greater than 460 meters/500 yards,
accuracy may not achieve ±1.0 meter/yard.
LED Illumination system
Orange color. Auto power on.
ActiveBrightnessControl(Dark:Lowintensity,Bright:High
intensity)
Target system First Target Priority System
Measuringmode Singlemode/Continuousmode(Approx.5seconds)
Optical system
Type Roof-prism monocular
Magnification(x) 6
Effectivediameterofobjectivelens(mm) ø21
Angularfieldofview(real)(˚) 7.5
Eyerelief(mm) 18.3
Exitpupil(mm) ø3.5
Diopter adjustment ±4m-1

En
Fr
Es
Pt
18 19
En
Fr
Es
Pt
* Waterproof models
The Nikon Callaway iQ is waterproof, and will suffer no damage to the optical system if submerged or dropped in water to a maximum depth of
1 meter for up to 10 minutes.
The Nikon Callaway iQ offers the following advantages:
• Canbeusedinconditionsofhighhumidity,dustandrainwithoutriskofdamage.
• Nitrogen-filleddesignmakesitresistanttocondensationandmold.
Observe the following when using the Nikon Callaway iQ.
• Theunitshouldnotbeoperatednorheldinrunningwater.
• Anymoistureshouldbewipedoffbeforeadjustingmovableparts(eyepiece,etc.)oftheNikonCallawayiQtopreventdamageandforsafety
reasons.
To keep your Nikon Callaway iQ in excellent condition, Nikon Vision recommends regular servicing by an authorized dealer.
**Thebatterychamberiswaterresistant,notwaterproof.WatermayenterthedeviceiftheNikonCallawayiQissubmergedinwater.Ifwater
enters the battery chamber, wipe out any moisture and allow time for the chamber to dry.
Specifications Others
Do not use the Nikon Callaway iQ for purposes beyond the limits of its stated accuracy.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
oftheFCCRulesandtoEUEMCdirective.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandreceiver.
•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
Others
Operatingtemperature(˚C) -10 —+50
Power source CR2 lithium battery x 1, 3V DC
Autopower-off(approx.8seconds)
Dimensions(LxHxW)(mm) 118 x 73 x 41
Weight(g) Approx.195(withoutbattery)
Structure Body:Waterproof(maximumdepthof1meterforupto10minutes)*
Batterychamber:Waterresistant**
Safety Class 1M Laser product (EN/IEC60825-1:2007)
EMC FCC Part 15 Subpart B Class B,
CE: EMC directive, C-tick, VCCI Class B
Environment RoHS, WEEE
Laser
Class EN/IECClass1M
Wavelength(nm) 905
Pulseduration(ns) 8
Output(W) 35
Beamdivergence(mrad) Vertical: 5.0, Horizontal: 0.25
Operatinghumidity(%RH) 80(withoutdewcondensation)