Ningbo Ginlong Technologies Solis 4G Operating instructions

Installation and Operation Manual
Solis 4G Three Phase Inverter
(5-10kW)
Ver 1.1
Ginlong (Ningbo) Technologies Co., Ltd.
Ningbo Ginlong Technologies Co., Ltd.
No. 57 Jintong Road, Binhai Industrial Park, Xiangshan, Ningbo,
Zhejiang, 315712, P.R.China.
Tel: [phone]
Fax: [phone]
If you encounter any problem on the inverter, please find out the inverter S/N
and contact us, we will try to respond to your question ASAP.

2
4
6
6
6
6
6
9
9
13
21
21
21
4
2
3
5
11
22
22
22
…………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………
………………………………………………………………………………………………………
……………………………………………………………………………………………………
………………………………………………………………………………………
……………………………………………………………………………………………………………………………
……………………………………………………………………………………………
………………………………………………………………………………………………………
…………………………………………………………………………………………………………………
…………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………
4
……………………………………………………………………………………………
24
………………………………………………………………………………………………………………………………
24
………………………………………………………………………………………………………………………
27
31
31
34
……………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………
7
7
8
…………………………………………………………………………………
………………………………………………………………………………………………………………
……………………………………………………………………………………………………………
1. Introduction
2. Safety Instructions
2.1 Safety Symbols
2.2 General Safety Instructions
2.3 Notice For Use
3. Overview
3.1 Front Panel Display
3.2 LED Status Indicator Lights
3.3 Keypad
3.4 LCD
5. Installation
5.1 Select Location for the Inverter
5.2 Mounting the Inverter
5.3 Electrical Connections
7. Operation
6. Start & Stop
6.1 Start the Inverter
6.2 Stop the Inverter
1.1 Product Description
1.2 Packaging
7.2 Information
7.1 Main Menu
4. Product handing and storage
4.1 Product handling
4.2 Product Storage
7.3 Settings
7.4 Advanced Info.
7.5 Advanced Settings
8. Maintenance
9. Troubleshooting
10. Specifications
……………………………………………………………………………………………………………………………………
Contents

1.1 Product Description
.3..2.
WiFi/GPRS Monitor the rodsx1
（apolegamy）
LED lights
LCD display
4 buttons
Figure 1.1 Front view
Figure 1.2 Bottom view
Inverter x1 Back plate x1
1.2 Packaging
When you receive the inverter, please ensure that all the parts listed below are included:
Expansion screw x3
Fastening screw x2 DC connector x2 User manual x1
Installation and Operation Manual
Solis 4G Three Phase Inverter
(5-10kW)
Ver 1.1
Ginlon g (Ning bo) Techn ologi es Co., L td.
1. Introduction 1. Introduction
If anything is missing, please contact your local Solis distributor.
Solis 4G three phase inverters integrate DRM and backflow power control function, that
could suitable for smart grid requirement.
Three phase 4G series inverter contain 6 models which are listed below:
Solis-3P5K-4G, Solis-3P6K-4G, Solis-3P8K-4G, Solis-3P9K-4G, Solis-3P10K-4G
Solis-3P5K-4G-LV

.5..4.
2. Safety Instructions 2. Safety Instructions
2.1 Safety Symbols
Safety symbols used in this manual, which highlight potential safety risks and important
safety information, are listed as follows:
2.2 General Safety Instructions
CAUTION:
Risk of electric shock from energy stored in capacitors of the Inverter.
Do not remove cover for 5 minutes after disconnecting all power sources
(service technician only). Warranty may be voided if the cover is removed
without unauthorized.
CAUTION:
The surface temperature of the inverter can exceed 75℃ (167F).
To avoid risk of burns, DO NOT touch the surface when inverter is operating.
The inverter must be installed out of reach of children.
2.3 Notice For Use
CAUTION:
CAUTION, RISK OF ELECTRIC SHOCK symbol indicates important safety
instructions, which if not correctly followed, could result in electric shock.
CAUTION:
CAUTION, HOT SURFACE symbol indicates safety instructions, which if not
correctly followed, could result in burns.
NOTE:
NOTE symbol indicates important safety instructions, which if not correctly
followed, could result in some damage or the destruction of the inverter.
WARNING:
WARNING symbol indicates important safety instructions, which if not
correctly followed, could result in serious injury or death.
WARNING:
Electrical installations must be done in accordance with the local and national
electrical safety standards.
WARNING:
Please don’t connect PV array positive(+) or negative(-) to ground, it could
cause serious damage to the inverter.
CAUTION:
The PV array (Solar panels) supplies a DC voltage when they are exposed to
sunlight.
WARNING:
To reduce the risk of fire, over-current protective devices (OCPD) are
required for circuits connected to the Inverter.
The DC OCPD shall be installed per local requirements. All photovoltaic
source and output circuit conductors shall have disconnects that comply
with the NEC Article 690, Part II. All Solis three phase inverters feature
an integrated DC switch.
CAUTION:
Risk of electric shock. Do not remove cover. There is no user serviceable
parts inside. Refer servicing to qualified and accredited service technicians.
The inverter has been constructed according to the applicable safety and technical
guidelines. Use the inverter in installations that meet the following specifications only:
1. Permanent installation is required.
2. The electrical installation must meet all the applicable regulations and standards.
3. The inverter must be installed according to the instructions stated in this manual.
4. The inverter must be installed according to the correct technical specifications.
5. To startup the inverter, the Grid Supply Main Switch (AC) must be switched on, before
the solar panel's DC isolator shall be switched on. To stop the inverter, the Grid Supply
Main Switch (AC) must be switched off before the solar panel's DC isolator shall be
switched off.

.7..6.
123
8
456 7
Light
1
2
3
POWE R
OP E RAT I ON
ALAR M
3. Overview
3.1 Front Panel Display
3.2 LED Status Indicator Lights
Status
ON
OFF
ON
OFF
OFF
ON
FLASHING
Description
The inverter can detect DC power.
No DC power or low DC power.
The inverter is operating properly.
The inverter has stopped to supply power.
The inverter is initializing.
Alarm or fault condition is detected.
The inverter is operating properly.
Figure 3.1 Front Panel Display
Table 3.1 Status Indicator Lights
3.3 Keypad
3.4 LCD
There are four keys in the front panel of the Inverter(from left to right):
ESC, UP, DOWN and ENTER keys. The keypad is used for:
Scrolling through the displayed options (the UP and DOWN keys);
Access to modify the adjustable settings (the ESC and ENTER keys).
The two-line Liquid Crystal Display (LCD) is located on the front panel of the Inverter,
which shows the following information:
Inverter operation status and data; Service messages for operator;
Alarm messages and fault indications.
4.1 Product handling
Please review the instruction below for handling the inverter:
1 The red circles below denote cutouts on the product package.
Push in the cutouts to form handles for moving the inverter (see Figure 4.1).
2
Figure 4.1 move the inverter
2.Open the carton, then handle both sides of inverter through the area denoted dotted line.
( see figure 4.2).
Figure 4.2 Inverter handles
4. Product handing and storage

≤15°
Vertical Backward
√ √
.9..8.
Use the original box to repackage the inverter, seal with adhesive tape with the desiccant
inside thebox.
4.2 Product Storage
To select a location for the inverter, the following criteria should be considered:
Do not install in small closed spaces where air cannot circulate freely. To avoid
overheating, always make sure the flow of air around the inverter is not blocked.
Exposure to direct sunlight will increase the operational temperature of the inverter and
may cause output power limiting. Ginlong recommends inverter installed to avoid
direct sunlight or raining.
To avoid over heating ambient air temperature must be considered when choosing
the inverter installation location. Ginlong recommends using a sun shade minimizing
direct sunlight when the ambient air temperature around the unit exceeds 104°F/40°C.
5.1 Select a Location for the Inverter
5. Installation
Figure 5.1 Recommended Installation locations
4. Product handing and storage

300mm
500mm 500mm
300mm 300mm
300mm 300mm
Inverted
× ×
.11..10.
The visibility of LED status indicator lights and LCD should be considered.
Install vertically (+/- 5°) or tilted backward (<=15°).
Don't mount inverter on the tilted forward wall.
Don't mount inverter on the horizontal.
NOTE:
Nothing should be stored on or placed against the inverter.
Figure 5.2 Inverter Mounting clearance
5.2 Mounting the Inverter
Dimensions of mounting bracket:
Figure 5.3 Inverter wall mounting
Refer to figure 5.4 and figure 5.5. Inverter shall be mounted vertically.
The steps to mount the inverter are listed below.
1. Refer to Figure 5.4, the holes for expansion bolt based on the hole diameter of bracket
(ST6.3*60 cross recessed hexagon head tapping screws, HJ0108 10*50mm fished
expandable tubular), using the percussion drilling with the 10mm drill need to stay
vertically on the wall.And the drill hole must be vertically on the wall.
And all drill holes' depth is 60mm.
Bracket
Suitable fixing screws
2. Make sure the bracket is horizontal. And the mounting holes (in Figure 5.4) are marked
correctly. Drill the holes into wall at your marks.
3. Use the suitable expansion screws to fix the bracket on the wall.
Figure 5.4 Inverter wall mounting
5. Installation5. Installation
Temperature of inverter heat sinker might 167℉/75℃.
Inverter is designed for working extreme environment, operation temperature range:
-15℉/25℃~149℉/65℃.
When 1 or more inverters are installed in one location, a minimum 12inchs clearance should
be kept between each inverter or other object. The bottom of the inverter should be 20inchs
clearance to the ground.

+
-
DC 1
DC 2
DC SWITCH
COM
GRID
.12. .13.
Locking screws
Figure 5.5 Install the inverter
Figure 5.6 Fixed the inverter
4. Lift the inverter and hang it on the backet, and fixing both sides of inverter with
locking screws (accessories).
WARNING:
The inverter must be mounted vertically.
5. Anti-theft lock mount(optional)
Anti-theft lock( User-supplied) function is that inverter is fixed in bracket in case theft.
The lock is selected by 5mm(the keyhole diameter), and the lock of stainless steel is
preferred.
Anti-theft lock
Figure 5.7 Install security lock
5.3 Electrical Connections
Inverter designs quick-connect terminal, so top cover needn't open during electrical
connection. The sign meaning located the bottom of inverter, as shown below in table 5.1.
All electrical connections are suit for the local or national standard.
Positive DC input terminal
Negative DC input terminal
Connecting terminal of the Grid
Switch of DC input terminals
RJ45 and terminal block for RS485 communication port
DC input terminal
DC input terminal
Table 5.1 Electrical connection symbols
5. Installation5. Installation
The electrical connection of the inverter must follow the steps listed below:
1. Switch the Grid Supply Main Switch (AC) OFF.
2. Switch the DC Isolator OFF.
3. Assemble PV input connector to the Inverter.

A
B
D
C
Grounding screw
.14. .15.
5. Installation5. Installation
5.3.1 Grounding
2) Prepare OT terminals: M6.
Solis recommends 2 ground protection methods: Through grid terminal connection
and external heat sink connection.
If AC terminal is used to connect ground, please refer to the contents of 5.3.2.
If the heat sink is used to connect the ground, please follow the steps below:
1) Prepare the grounding cable: recommend to use the ≥ 6mm² outdoor
copper-core cable.
Important:
3) Strip the ground cable insulation to a suitable length(see Figure 5.8).
Figure 5.8 suitable length
Important:
Figure 5.9 strip wire
Important:
For multiple inverters in parallel , all inverters should be connected to the
same ground point to eliminate the possibility of a voltage potential existing
between inverter grounds.
B (insulation stripping length) is 2mm~3mm longer than A (OT cable
terminal crimping area) 2mm~3mm.
After crimping the terminal to the wire, inspect the connection to ensure the
terminal is solidly crimped to the wire.
5) Remove the screw from the heat sink ground point.
6) Connect the grounding cable to the grounding point on the heat sink,and tighten the
grounding screw, Torque is 3Nm(see figure 5.10).
Figure 5.10 Fixed cable
For improving anti-corrosion performance,
after ground cable installed, apply silicone or paint is preferred to protect.
Important:
4) Insert the stripped wire into the OT terminal crimping area and use the hydraulic
clamp to crimp the terminal to the wire (see Figure 5.9).

+
-
4.0~6 .0 4. 0（12AWG）
（12~10 AWG）
.17..16.
5. Installation5. Installation
Before connecting inverter, please make sure the PV array open circuit
voltage is within the limit of the inverter.
Before connection, please make sure the polarity of the output voltage of
PV array matches the“DC+”and“DC-”symbols.
Before connecting inverter, please make sure the PV array open circuit
voltage is within the limit of the inverter.
Figure 5.11 DC+ Connector Figure 5.12 DC- Connector
Please use approved DC cable for PV system.
Cable type
Cross section（mm²）
Range
Industry generic P V cable
（model:PV1-F）
Recommended value
Figure 5.13 Disassemble the Connector Cap nut Figure 5.14 Insert the Wire into the
Connector Cap nut and contact pin
Figure 5.15 Crimp the contact pin to the wire Figure 5.16 Connector with Cap nut Screwed on
Figure 5.17 Multimeter measurement Figure 5.18 Connect the DC
Connectors to the Inverter
The steps to assemble the DC connectors are listed as follows:
1. Strip off the DC wire for about 7mm, Disassemble the connector cap nut. (see Figure 5.13)
3. Crimp the contact pin to the wire using a proper wire crimper. (see Figure 5.15)
2. Insert the wire into the connector cap nut and contact pin. (see Figure 5.14)
4. Insert metal connector into top of connector, and tighten nut with torque 2.5-3 Nm
(see figure 5.16).
Crimping plier
5. Measure PV voltage of DC input with multimeter, verify DC input cable polar
(see figure 5.17), and ensure each string of PV voltage in range of inverter operation.
Connect DC connector with inverter until hearing a slight clicking sound indicates
connection succeed. (see figure 5.18)
WARNING:
If DC input wire reverses, please not operate DC switch, DC1and DC2
instantly to avoid inverter damage.. Damage caused by this reason isn't
covered by warranty.
Solution: Until reduced sun irradiance and PV voltage is below 0.5 A(mostly
in evening), then put DC switch in “off” position, remove “+”, “-” connectors to
reconnect wires.
5.3.2 Connect PV side of inverter

.19..18.
5. Installation5. Installation
5.3.3 Connect grid side of inverter
B) Insert the cable through the jacket and cap nut of connector, then insert the wires to the grid
terminal and tighten the screws on the connector (see figure 5.22).
Please try to pull out the wire to make sure it is well connected.
Internal of AC connector signs "L1","L2","L3","N" and "PE " five connection
ports (see Figure 5.20). Three live wires are connected the "L1", "L2"and
"L3" terminals respectively; ground wire connects "PE "; neutral wire
connects "N" terminal:
Figure 5.23 AC connector to inverter
For all AC connections, 2.5 – 6 mm², 105°C cable is required to be used. Please make sure the
resistance of cable is lower than 1.50hm. If the wire is longer than 20m, preferred to 6mm² cable.
Please fixed cable with PH1 cross screwdriver.
Each inverter has a corresponding AC grid terminal connector. See figure 5.19.
Figure 5.19
AC Grid Terminal Connector
Figure 5.20
AC Grid Terminal Connector Inside
L3
N
L1
PE
The steps to assemble AC grid terminal connector are listed as follows:
A) Strip the end of AC wire about 8mm. See figure 5.21 left.
Figure 5.21 Connect Wires to the Grid Terminal
Figure 5.22 Connected cable
C) Assemble the connector and tighten up cap on the terminal. See Figure 5.21 right.
D) Connect AC grid terminal connector to the inverter, small click will confirm that connection
is appropriate. (see figure 5.23)
PH1 cross screwdriver
L2

Solis-3P5K-4G 400
Current for protection
device (A)
7.2
8.7
20
11.5
Solis-3P8K-4G
Solis-3P6K-4G
20
20
13.0
14.4
13.1
Solis-3P10K-4G
Solis-3P5K-4G-LV
Solis-3P9K-4G
32
32
32
400
400
400
400
208/220/240
.21..20.
5. Installation
Inverter Rated voltage(V) Rated output
current (A)
To protect the inverter's AC grid connection conductors, Solis recommends installing
breakers that will protect against overcurrent. The following table defines OCPD ratings for
the Solis 5-10kW three phase inverters.
5.3.4 Max. over current protection device (OCPD)
Table 5.2 Rating of grid OCPD
5.3.5 Inverter monitoring connection
The inverter can be monitored via Wi-Fi or GPRS. All Solis communication devices are
optional (Figure 5.24). For connection instructions, please refer to the Solis Monitoring
Device installation manuals.
GPRS monitoring
Wi-Fi monitoring
Wi-Fi monitoring
Router
Wi-Fi box
Internet
Smart phone monitoring
PC monitoring
Web server
Figure 5.24 Wireless communication function
6. Start & Stop
6.1 Start the Inverter
To start up the Inverter, it is important that the following steps are strictly followed:
1. Switch the grid supply main Switch (AC) ON first.
2. Switch the DC switch ON. If the voltage of PV arrays are higher than start up voltage,
the inverter will turn on. The red LED power will light.
3. When both the DC and the AC sides supply to the inverter, it will be ready to generate
power. Initially, the inverter will check both its internal parameters and the parameters
of the AC grid, to ensure that they are within the acceptable limits. At the same time,
the green LED will flash and the LCD displays the information of INITIALIZING.
4. After 30-300 seconds (depending on local requirement), the inverter will start to
generate power. The green LED will be on continually and the LCD displays
GENERATING.
WARNING:
Do not touch the surface when the inverter is operating. It may be
hot and cause burns.
6.2 Stop the Inverter
To stop the Inverter, the following steps must be strictly followed:
1. Turn off the ac switch.
2. Put the DC SWITCH on the inverter in the position of "OFF".
3. Remove the positive and negative dc lines and remove the ac lines.

5.2 Stop the Inverter
.23..22.
In normal operation, LCD screen alternatively shows inverter power and operation status
(see Figure 7.1). The screen can be scrolled manually by pressing the UP/DOWN keys.
Pressing the ENTER key gives access to Main Menu.
5 sec
Start
Power 3424W
01-01-2014 12:04
Status: Generating
01-01-2014 12:04
Information
Settings
Advanced Info.
Advanced settings
UP/DOWN
UP/DOWN
UP/DOWN
UP/DOWN or
auto-scroll
(10 sec)
Pressing the
ENTER key
gives access to
the main menu.
Pressing the
ESC key
calls back the
previous menu.
Main Menu
Figure 7.1 Operation Overview
7.1 Main Menu
There are four submenus in the Main Menu (see Figure 7.1):
1. Information
2. Settings
3. Advanced Info.
4. Advanced Settings
The Solis three Phase 4G Inverter main menu provides access to operational data and
information. The information is displayed by selecting "Information" from the menu
and then by scrolling up or down.
7.2 Information 7.2.1 Lock screen
Pressing the ESC key returns to the Main Menu. Pressing the ENTER key locks
(Figure 7.2(a)) or unlocks (Figure 7.2 (b)) the screen.
(b)(a)
Figure 7.2 Locks and Unlocks the Screen of LCD
7. Operation7. Operation
Table 7.1 Information list
V_DC1 350.8V
I_DC1 5.1A
V_A 230.4V
I_ A 8.1A
Status: Generating
Power: 1488W
Grid Frequency
F_Grid 50.06Hz
Total Energy
0258458 kwh
This Month: 0123kwh
Last Month: 0123kwh
Today: 15.1kwh
Yesterday: 13.5kwh
10 sec
10 sec
10 sec
10 sec
10 sec
10 sec
10 sec
V_DC1: Shows input 01 voltage value.
I_DC1: Shows input 01 current value.
V_A: Shows the grid's voltage value.
I_A: Shows the grid's current value.
Status: Shows instant status of the Inverter.
Power: Shows instant output power value.
F_Grid: Shows the grid's frequency value.
Total generated energy value.
This Month: Total energy generated this month.
Last Month: Total energy generated last month.
Today: Total energy generated today.
Yesterday: Total energy generated yesterday.
Display Duration Description
Inverter SN
00000000000000
10 sec
Display series number of the inverter.
V_ D C2 350.8V
I_ D C2 5.1A 10 sec V_DC2: Shows input 02 voltage value.
I_DC2: Shows input 02 current value.
10 sec
V_C 230.4V
I_ C 8.1A
V_C: Shows the grid's voltage value.
I_C: Shows the grid's current value.

.25..24.
The following submenus are displayed when the Settings menu is selected:
1. Set Time
2. Set Address
7.3 Settings
7.3.1 Set Time
This function allows time and date setting. When this function is selected, the LCD will
display a screen as shown in Figure 7.3.
NEXT=<ENT> OK=<ESC>
01-01-2016 16:37
Figure 7.3 Set Time
Press the UP/DOWN keys to set time and data. Press the ENTER key to move from one
digit to the next (from left to right). Press the ESC key to save the settings and return to
the previous menu.
7.3.2 Set Address
This function is used to set the address when muti inverters are connected to three monitor.
The address number can be assigned from “01”to “99”(see Figure 7.4). The default address
number of Solis Three Phase Inverter is “01”.
YES=<ENT> NO=<ESC>
Set Address: 01
Figure 7.4 Set Address
Press the UP/DOWN keys to set the address. Press the ENTER key to save the settings.
Press the ESC key to cancel the change and return to the previous menu.
7.4 Advanced Info - Technicians Only
NOTE:
To access to this area is for fully qualified and accredited technicians only.
Enter menu “Advanced Info.” and “Advanced settings” （need password）.
Select “Advanced Info.” from the Main Menu. The screen will require the password as below:
YES=<ENT> NO=<ESC>
Password:0000
Figure 7.5 Enter password
After enter the correct password the Main Menu will display a screen and be able to access
to the following information.
1. Alarm Message 2. Running message 3.Version 4. Daily Energy
5. Monthly Energy 6. Yearly Energy 7. Daily Record 8. Communication Data
The screen can be scrolled manually by pressing the UP/DOWN keys. Pressing the ENTER
key gives access to a submenu. Press the ESC key to return to the Main Menu.
7.4.1 Alarm Message
The display shows the latest alarm messages (see Figure 7.6). Screens can be scrolled 100
manually by pressing the UP/ DOWN keys. Press the ESC key to return to the previous
menu.
Alarm001: OV-G-V
Time: 27-11 Data: 7171
Figure 7.6 Alarm Message
7.4.2 Running Message
This function is for maintaince person to get running message such as internal temperature,
Standard No.1,2,etc.
Screens can be scrolled manually by pressing the UP/DOWN keys.
7.4.3 Version
The screen shows the model version and the software version of the Inverter
(see Figure 7.7).
Model: 08
Software Version: D20001
Figure 7.7 Model Version and Software Version
7. Operation7. Operation

.27..26.
7.4.4 Daily Energy
The function is for checking the energy generation for selected day.
Figure 7.8 Select date for daily energy
YES=<ENT> NO=<ES C>
Select: 2015-02-23
Press D OW N key to move the cursor to day, month and year, press UP key to change the
digit. Press Enter after the date is fixed.
2015-02-22: 051.3kWh
2015-02-23: 061.5kWh
Figure 7.9 Daily energy
Press U P/DO WN key to move one date from another.
7.4.5 Monthly Energy and Yearly Energy
The two functions are for checking the energy generation for selected month and Year.
YES=<ENT> NO=<ES C>
Select: 2015-02
YES=<ENT> NO=<ES C>
Select: 2015
Figure 7.10 Select month for monthly energy Figure 7.11 Select year for yearly energy
Press D OW N key to move the cursor, press UP key to change the
digit. Press Enter after the month/year is fixed.
2015-02: 0510kWh
2015-01: 0610kWh
2015: 0017513kWh
2014: 0165879kWh
Figure 7.12 Month energy Figure 7.13 Yearly energy
Press U P/DO WN key to move one date from another.
7.4.6 Daily record
The screen shows history of changing settings. Only for maintance personel.
7.4.7 Communication Data
The screen shows the internal data of the Inverter (see Figure 7.14), which is for service
technicians only.
01-05: 01 25 E4 9D AA
06-10: C2 B5 E4 9D 55
Figure 7.14 Communication Data
7.5 Advanced Settings - Technicians Only
NOTE:
To access to this area is for fully qualified and accredited technicians only.
Please follow 7.4 to enter password to access this menu.
Select Advanced Settings from the Main Menu to access the following options:
1. Select Standard 2. Grid ON/OFF 3. Clear Energy 4. New Password
5. Power Control 6. Calibrate Energy 7.STD. Mode Settings
7.5.1 Selecting Standard
This function is used to select the grid's reference standard (see Figure 7.15).
YES=<ENT> NO=<ESC>
Standard:AUS-Q-0.8
Figure 7.15
Press the UP/DOWN keys to select the standard (AS4777, VDE4105, VDE0126, UL-240V-A,
UL-208V-A, UL-240V, UL-208V, MEX-CFE, G83/2 (for 1-3.6kW models), G59/3 (for 4-5kW
models), EN50438 DK, EN50438 IE, EN50438 NL and “User-Def” function). Press the
ENTER key to confirm the setting. Press the ESC key to cancel changes and returns to
previous menu.
NOTE:
This function is for technicians use only.
7. Operation7. Operation

OV-G-V1: 220---290V OV-G-F1: 50.2-53Hz(60.2-64Hz)
OV-G-V1-T: 0.1---9S OV-G-F1-T: 0.1---9S
OV-G-V2: 220---290V OV-G-F2: 50.2-53Hz(60.2-64Hz)
OV-G-V2-T: 0.1---1S OV-G-F2-T: 0.1---9S
UN-G-V1: 90---210V UN-G-F1: 47-49.5Hz(56-59.8Hz)
UN-G-V1-T: 0.1---9S UN-G-F1-T: 0.1---9S
UN-G-V2: 90---210V UN-G-F2: 47-49Hz(56-59.8Hz)
UN-G-V2-T: 0.1---1S UN-G-F2-T: 0.1---9S
.29..28.
Startup-T:10---600S
Restore-T:10---600S
Below is the setting range for “User-Def”. Using this function, the limits can be changed
manually.
Press the UP/DOWN keys to scroll through items. Press the ENTER key to edit the highlighted
item. Press the UP/DOWN keys again to change the setting. Press the ENTER key to save the
setting. Press the ESC key to cancel changes and returns to the previous menu.
7.5.2 Grid ON/OFF
This function is used to start up or stop the power generation of Solis Three Phase
Inverter (see Figure 7.17).
Grid ON
Grid OFF
Figure 7.17 Set Grid ON/OFF
Screens can be scrolled manually by pressing the UP/DOWN keys. Press the ENTER key
to save the setting. Press the ESC key to return to the previous menu.
These two functions are applicable by maintenance personnel only, wrong
operation will prevent the inverter from working properly.
7.5.4 New Password
This function is used to set the new password for menu “Advanced info.” and “Advanced
information” (see Figure 7.18).
Figure 7.18 Set new password
YES=<ENT> NO=<ESC>
Password: 0000
Enter the right password before set new password. Press the DOWN key to move the cursor,
Press the UP key to revise the value. Press the ENTER key to execute the setting.
Press the ESC key to return to the previous menu.
7.5.5 Power control
Active and reactive power can be set through power setting button.
There are 5 item for this sub menu:
1. Set output power 2. Set Reactive Power 3. Out_P With Restore
4. Rea_P With Restore 5. Select PF Curve
This function is applicable by maintenance personnel only, wrong operation
will prevent the inverter from reaching maximum power.
Selecting the “User-Def” menu will access to the following submenu (see Figure 7.16),
Figure 7.16
OV-G-V1: 260V
OV-G-V1-T: 1S
NOTE:
The " User-Def" function can be only used by the service engineer and
must be allowed by the local energy supplier.
7.5.3 Clear Energy
Clear Energy can reset the history yield of inverter
7.5.6 Calibrate Energy
Maintenance or replacement could clear or cause a different value of total energy. Use this
function could allow user to revise the value of total energy to the same value as before. If
the monitoring website is used the data will be synchronous with this setting automatically.
(see Figure 7.19).
7. Operation7. Operation

.31..30.
Figure 7.19 Calibrate energy
YES=<ENT> NO=<ESC>
Energy:0000000kWh
Press the DOWN key to move the cursor, Press the UP key to revise the value. Press the
ENTER key to execute the setting. Press the ESC key to return to the previous menu.
8. Maintenance
7. Operation
Solis Three Phase Inverter does not require any regular maintenance. However, cleaning
the dust on heat-sink will help the inverter to dissipate the heat and increase its life time.
The dust can be removed with a soft brush.
CAUTION:
Do not touch the inverter's surface when it is operating. Some parts of the
inverter may be hot and cause burns. Turn off the inverter (refer to Section
6.2) and wait for a cool-down period before before any maintenance or
cleaning operation.
The LCD and the LED status indicator lights can be cleaned with a damp cloth if they are too
dirty to be read.
NOTE:
Never use any solvents, abrasives or corrosive materials to clean the inverter.
The inverter is designed in accordance with the most important international grid-tied
standards and safety and electromagnetic compatibility requirements. Before delivering to
the customer, the inverter has been subjected to several tests to ensure its optimal operation
and reliability.
In case of failure, the LCD screen will display an alarm message. In this case, the inverter
may stop feeding into the grid. The failure descriptions and their corresponding alarm
messages are listed in Table 9.1:
9. Troubleshooting
7.5.7 STD setting
Solis 4G inverter could set different work mode to work with different grid requirement.
There are 4 items under STD mode setting.
1. Working Mode Set 2. Power Rate Limit 3. Freq Derate Set
4. 10mins Voltage Set 5. Initial Settings.
There are 6 items in working mode submenu.
1. NULL,Volt-watt 2. Volt-var 3. Fixed-PF 4. Reac-power 5. Power-PF
There are 2 items in power rate limit submenu.
1. Power Rate: 0-100% 2. RateP_Sts-US: stop/run
There are 3 items in Freq Derate Set submenu.
1. over Freq 2. under Freq 3. Derate mode.
There are 5 items in initial setting submenu.
1. Work mode default 2. Power rate default 3. Fre Derate Default
4. 10mVvoltage Default 5. DRM ON/OFF
There is 1 item in 10mins voltage set submenu.
1. 10mins voltage：244-258V.

9. Trouble Shooting9. Trouble Shooting
Alarm Message
OV-G-V01/02/03/04
OV-G-F01/02
UN-G-F01/02
G-IMP
NO-GRID
OV-DC01/02/03/04
OV-BU S
UN-BUS01/02
GRID-I N TF01/02
INI-FAULT
OV-TE M
Failure description
Over grid voltage
Under grid voltage
Over grid frequency
Under grid frequency
High grid impedance
No grid voltage
Over D C voltage
Over D C bus voltage
Under DC bus voltage
Grid interference
Initialization system fault
Over Temperature
Solution
1.Resistant of AC cable is too high.
Change bigger size grid cable
2.Adjust the protection limit if it’s
allowed by electrical company.
1.Check connections and grid switch.
2.Check the grid voltage inside inverter
terminal.
1.Reduce the module number in series
1.Restart inverter
2.Change power board
1.Check P V input connections
2.Check D C input voltage
(single phase >120V, three phase >350V)
3.Check if PV+/- is reversed
Inverter no power
on LCD
No power
LCD show initializing
all the time Can not start-up
1.Check if the connector on main
board or power board are fixed.
2.Check if the D SP connector to
power board are fixed.
1.Check inverter surrounding ventilation.
2.Check if there’s sunshine direct on
inverter in hot weather.
1.Use user define function to adjust the
protection limit if it’s allowed by
electrical company.
1.Check inverter inductor connection
2.Check driver connection
1.Restart inverter or contact installer.
UN-G-V01/02
DC-INT F D C input overcurrent
1.Restart inverter
2.Identify and remove the string to the fault MPPT
2.Change power board
IGFO L -F Grid current tracking fail
OV-G-I Over grid current
OV-DC A-I
IGBT-OV-I Over I G BT current
12Power-FA U LT 12V power supply fault
1.Restart inverter or contact installer.
IG-AD Grid current sampling fail
DSP-B-FAULT Comm. failure between main
and slave D SP
Table 9.1 Fault message and description
1.Remove all D C input, reconnect and
restart inverter one by one.
2.Identify which string cause the fault and
check the isolation of the string.
DCinj-FAULT High DC injection current
1.Check AC and DC connection
2.Check inverter inside cable connection.
1.Restart inverter or contact installer.
Alarm Message Failure description Solution
PV ISO-PRO
01/02 PV isolation protection
ILeak-PRO
01/02/03/04 Leakage current protection
RelayChk-FAIL Relay check fail
NOTE:
If the inverter displays any alarm message as listed in Table 9.1; please
turn off the inverter (refer to Section 5.2 to stop your inverter) and wait for 5
minutes before restarting it (refer to Section 5.1 to start your inverter). If the
failure persists, please contact your local distributor or the service center.
Please keep ready with you the following information before contacting us.
1. Serial number of Solis Three Phase Inverter;
2. The distributor/dealer of Solis Three Phase Inverter (if available);
3. Installation date.
4. The description of problem (i.e. the alarm message displayed on the LCD and the status
of the LED status indicator lights. Other readings obtained from the Information submenu
(refer to Section 6.2) will also be helpful.);
5. The PV array configuration (e.g. number of panels, capacity of panels, number of strings
, etc.);
6. Your contact details.
AFCI self-detection
(model with AFCI
module)
AFCI module self-detect fault 1.Restart inverter or connect technician.
Arcing protection
(model with AFCI
module)
Detect arc in DC circuit 1. Check inverter connection whether arc
exists and restart inverter.
.33..32.

10. Specifications 10. Specifications
.35..34.
3/N/PE~400
47...52 or 57...62
Max. DC input voltage (Volts)
MPPT voltage range (Volts)
Max. input current (Amps)
MPPT number/Max input strings number
Rated grid voltage (Volts)
Rated output current (Amps)
Power Factor (at rated output power)
Operating frequency range (Hertz)
Max.efficiency
EU efficiency
MPPT efficiency
Max. DC input power (Watts)
Grid voltage range (Volts)
Model
Dimensions
Weight
Topology
Operating ambient temperature range
Ingress protection
Noise emission (typical)
Cooling concept
Max.operation altitude
Designed lifetime
Connention
Grid connection standard
Operating surroundings humidity
310W*538H*158D (mm)
1000
11+11
17.2+17.2
2/2
313...470
0.8leading~0.8lagging
50/60
98.3%
97.8%
>99.5%
13.6kg
Transformerless
IP65
<30 dBA
Natural convection
4000m
>20 years
-25℃. .. 60℃
Display
Monitoring
Communication connections
Warranty Terms
Rated output power (Watts)
Max. output power (Watts)
Max. apparent output power (VA)
0...100% Condensing
Mc4 connector and Ip67 rated plug
LCD, 2×20 Z.
WiFi or GPRS
4 pins RS485 connector
5 Years STD (Extendable to 20 Years)
EN50438, G83/2, AS4777.2:2015,
VDE0126-1-1, IEC61727, VDE N4105
600
5000
5500
5500
7.2
Solis-3P5K-4G
6000
THDi (at rated output power) <1.5%
160...850
Start-up voltage (Volts) 180
Max short circuit input current (Amps)
Rated DC voltage (Volts)
Rated grid frequency (Hertz)
3/N/PE~400
47...52 or 57...62
Max. DC input voltage (Volts)
MPPT voltage range (Volts)
Max. input current (Amps)
MPPT number/Max input strings number
Rated grid voltage (Volts)
Rated output current (Amps)
Power Factor (at rated output power)
Operating frequency range (Hertz)
Max.efficiency
EU efficiency
MPPT efficiency
Max. DC input power (Watts)
Grid voltage range (Volts)
Model
Dimensions
Weight
Topology
Operating ambient temperature range
Ingress protection
Noise emission (typical)
Cooling concept
Max.operation altitude
Designed lifetime
Connention
Grid connection standard
Operating surroundings humidity
310W*538H*158D (mm)
1000
11+11
17.2+17.2
2/2
313...470
0.8leading~0.8lagging
50/60
98.3%
97.8%
>99.5%
13.6kg
Transformerless
IP65
<30 dBA
Natural convection
4000m
>20 years
-25℃. .. 60℃
Display
Monitoring
Communication connections
Warranty Terms
Rated output power (Watts)
Max. output power (Watts)
Max. apparent output power (VA)
0...100% Condensing
Mc4 connector and Ip67 rated plug
LCD, 2×20 Z.
WiFi or GPRS
4 pins RS485 connector
5 Years STD (Extendable to 20 Years)
EN50438, G83/2, AS4777.2:2015,
VDE0126-1-1, IEC61727, VDE N4105
600
6000
6600
6600
8.7
Solis-3P6K-4G
7200
THDi (at rated output power) <1.5%
160...850
Start-up voltage (Volts) 180
Max short circuit input current (Amps)
Rated DC voltage (Volts)
Rated grid frequency (Hertz)

.36. .37.
10. Specifications 10. Specifications
3/N/PE~400
47...52 or 57...62
Max. DC input voltage (Volts)
MPPT voltage range (Volts)
Max. input current (Amps)
MPPT number/Max input strings number
Rated grid voltage (Volts)
Rated output current (Amps)
Power Factor (at rated output power)
Operating frequency range (Hertz)
Max.efficiency
EU efficiency
MPPT efficiency
Max. DC input power (Watts)
Grid voltage range (Volts)
Model
Dimensions
Weight
Topology
Operating ambient temperature range
Ingress protection
Noise emission (typical)
Cooling concept
Max.operation altitude
Designed lifetime
Connention
Grid connection standard
Operating surroundings humidity
310W*538H*158D (mm)
1000
11+11
17.2+17.2
2/2
313...470
0.8leading~0.8lagging
50/60
98.7%
98.1%
>99.5%
14.1kg
Transformerless
IP65
<30 dBA
Natural convection
4000m
>20 years
-25℃. .. 60℃
Display
Monitoring
Communication connections
Warranty Terms
Rated output power (Watts)
Max. output power (Watts)
Max. apparent output power (VA)
0...100% Condensing
Mc4 connector and Ip67 rated plug
LCD, 2×20 Z.
WiFi or GPRS
4 pins RS485 connector
5 Years STD (Extendable to 20 Years)
EN50438, G83/2, AS4777.2:2015,
VDE0126-1-1, IEC61727, VDE N4105
600
8000
8800
8800
11.5
Solis-3P8K-4G
9600
THDi (at rated output power) <1.5%
160...850
Start-up voltage (Volts) 180
Max short circuit input current (Amps)
Rated DC voltage (Volts)
Rated grid frequency (Hertz)
3/N/PE~400
47...52 or 57...62
Max. DC input voltage (Volts)
MPPT voltage range (Volts)
Max. input current (Amps)
MPPT number/Max input strings number
Rated grid voltage (Volts)
Rated output current (Amps)
Power Factor (at rated output power)
Operating frequency range (Hertz)
Max.efficiency
EU efficiency
MPPT efficiency
Max. DC input power (Watts)
Grid voltage range (Volts)
Model
Dimensions
Weight
Topology
Operating ambient temperature range
Ingress protection
Noise emission (typical)
Cooling concept
Max.operation altitude
Designed lifetime
Connention
Grid connection standard
Operating surroundings humidity
310W*538H*158D (mm)
1000
11+11
17.2+17.2
2/2
313...470
0.8leading~0.8lagging
50/60
98.7%
98.1%
>99.5%
14.1kg
Transformerless
IP65
<30 dBA
Natural convection
4000m
>20 years
-25℃. .. 60℃
Display
Monitoring
Communication connections
Warranty Terms
Rated output power (Watts)
Max. output power (Watts)
Max. apparent output power (VA)
0...100% Condensing
Mc4 connector and Ip67 rated plug
LCD, 2×20 Z.
WiFi or GPRS
4 pins RS485 connector
5 Years STD (Extendable to 20 Years)
EN50438, G83/2, AS4777.2:2015,
VDE0126-1-1, IEC61727, VDE N4105
600
9000
9900
9900
13
Solis-3P9K-4G
10800
THDi (at rated output power) <1.5%
160...850
Start-up voltage (Volts) 180
Max short circuit input current (Amps)
Rated DC voltage (Volts)
Rated grid frequency (Hertz)