Ninja PROFESSIONAL XL User manual

FOOD PROCESSOR
PROFESSIONAL XL
Please make sure to read the enclosed Ninja® Safety Instructions prior to using your unit.
For questions or to register your product,
visit us online at ninjakitchen.com
@ninjakitchen
© 2022 SharkNinja Operating LLC.
AUTO-IQ, NINJA, and PRECISION PROCESSOR are registered trademarks of SharkNinja Operating LLC.
NF700_QSG_MP_Mv5
Scan the code for online help, FAQs, and How-To Videos.
ninjakitchen.com
GET TO KNOW THE ATTACHMENTS
BLADE ASSEMBLIES
3-PART FOOD PUSHER
DISC ASSEMBLIES
DISC SPINDLE
Install disc spindle onto the gear
shaft of the Precision Processor®
Bowl to use the disc assemblies.
STORAGE BOX
(not included with all models)
Easily and safely store the disc
assemblies, disc spindle, and
dough blade assembly in the
storage box. To purchase, visit
ninjaaccessories.com.
DOUGH BLADE
ASSEMBLY
CHOPPING BLADE
ASSEMBLY
SLICING SHREDDING
S
H
R
E
D
D
E
R
S
L
I
C
E
R
REVERSIBLE SLICING/
SHREDDING
The reversible slicing/shredding
disc is perfect for outputs like
thinly sliced cucumbers and
shredded carrots. Face the side
labeled SLICER up for slicing
and face the side labeled
SHREDDER up for shredding.
3-PART FOOD PUSHER
The 3-part food pusher separates into small, medium, and large food pushers
to guide ingredients through the dierent-sized feed chute openings. Use
the small feed chute opening (which also doubles as a measuring cup) for
ingredients like carrots, the medium feed chute for ingredients like cucumbers
and zucchini, and the large feed chute for ingredients like potatoes.
NOTE:As a safety feature, the large food pusher must be inserted in the feed chute for
the unit to run. DO NOT exceed the CHUTE MAX FILL line on the large feed
chute. Unit will not run if ingredients exceed this line.
Intelligent preset programs combine unique blending and pausing patterns that do the work for you.
Once an Auto-iQ program is selected, it will start immediately and automatically stop when processing
is complete. To stop processing before the end of a program, press the currently active button again.
NOTE: Program run times vary from a few seconds to just over a minute.
AUTO-IQ® PROGRAMS
MANUAL PROGRAMS
LOW and HIGH: When selected, each
of these speeds runs continuously
for 60 seconds. They do not work in
conjunction with any Auto-iQ programs.
PULSE: Oers greater control of pulsing and
processing. Operates only when PULSE is
pressed. Use short presses for short pulses
and long presses for long pulses.
CHOP
Timed pulses and pauses give you consistent chopping results.
Run program once for a large chop, twice for a small chop, and
three times for a mince. Use with chopping blade assembly.
DOUGH
Ideal for creating delicious dough, from pie to pizza to cookie
doughs. Use with the dough blade assembly.
NOTE: Use PULSE to add mix-ins, such as chocolate chips or raisins, after
dough program has completed.
PUREE
Create anything from silky-smooth sauces to the perfect hummus.
Use with the chopping blade assembly or nesting workbowl with
small chopping blade assembly.
DISC
Slice and shred a variety of ingredients, such as vegetables, cheese.
Use with reversible slicing/shredding disc.
NOTE: Unit color may vary by model.
IMPORTANT: DO NOT run the unit on HIGH if using the dough blade or disc assemblies. The unit is
NOT intended to crush ice. Refer to the warnings in the Safety Instructions.
QUICK START GUIDE

USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
PROCESS & ENJOY
1.
Select desired
program to
begin processing.
2.
When processing
is complete, press
button on feed
chute lid near handle
to unlock. Turn lid
counterclockwise and
lift from bowl.
Remove blade assembly
before emptying bowl.
PARTS
3.
Place ingredients
in bowl. Place lid
on bowl and turn
clockwise to lock
in place.
BLADE ASSEMBLY
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before pouring,
carefully remove Chopping Blade Assembly. Failure to do so will result in a risk of
laceration. Refer to the Ninja Safety Instructions for additional information.
1.
Place Precision
Processor Bowl
on base and
turn clockwise
to lock in place.
3.
Remove bowl
from base
by turning it
counterclockwise,
then lifting it up.
2.
Holding the blade
assembly by the
top of the shaft,
install it in bowl.
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button to turn the unit on.
PRECISION PROCESSOR®
BOWL & LID WITH
3-PART FOOD PUSHER
CHOPPING BLADE
ASSEMB LY
DOUGH BLADE
ASSEMB LY
PARTS
FOOD PREP
DISC ASSEMBLY
USING THE DISC ASSEMBLIES
2. REVERSIBLE
SLICING/SHREDDING
Use plastic grip to place
disc over spindle with the
desired output facing up.
Use the side labeled
SLICER for slicing and the
side labeled SHREDDER
for shredding.
1.
Place Precision Processor®
Bowl on base and turn
clockwise to lock in place.
Install the spindle, then
place the disc on the spindle.
REVERSIBLE
SLICING/SHREDDING DISC
If using the small or medium feed chute, trim ingredients to fit the feed chute height.
If using the larger feed chute, DO NOT exceed the CHUTE MAX FILL line on the large
feed chute. Unit will not run if ingredients exceed this line.
Cut both ends o ingredients to create
flat surfaces. Trim tapered ingredients like
carrots to make them more symmetrical.
SHREDDING
SLICING
DISC
SPINDLE
S
H
R
E
D
D
E
R
S
L
I
C
E
R
PRECISION PROCESSOR®
BOWL & LID WITH
3-PART FOOD PUSHER
2B.
If using the large feed chute
opening, place ingredients
up to, but not exceeding,
the CHUTE MAX FILL line.
Insert the pusher into the
feed chute, then select
DISC or LOW. The disc
will begin spinning.
2A.
If using the small or medium
feed chute opening, select
DISC or LOW. The disc will
begin spinning. Add
ingredients through the
feed chute on the lid.
4.
Remove the disc assembly
by grasping the plastic grip,
then remove the disc spindle.
Remove bowl from base by
turning it counterclockwise,
then lifting it up.
3.
The disc will automatically
stop spinning at the end
of the program. Wait for
disc to stop turning, then
press the button on the
feed chute lid near the
handle to unlock. Turn lid
counterclockwise and lift
lid from bowl.
PROCESS & ENJOY (DISCS)
1.
Place feed chute lid on bowl and turn
clockwise. Based on the ingredient, use
the smallest possible feed chute opening
for best slicing and shredding results.
IMPORTANT: As a safety feature, the large food pusher must be inserted in the feed
chute for the unit to run.
Once the Precision Processor® Bowl is locked onto base, plug in the unit,
then press the Power button to turn the unit on.
NOTE: Large food pusher must be inserted in the feed chute for the unit to run. For thinner recipes such
as sauces and chopping, make sure all 3 parts of the pusher are installed to avoid splatter.
NOTE:
• Ensure cheese is well chilled before slicing/shredding. DO NOT slice or shred frozen cheese.
• Keep ingredients as steady as possible when pushing through the feed chute. This will help
minimize waste.
NOTE: Not all accessories are included with all models.
IMPORTANT: Use only the DISC program or LOW setting when using the disc assemblies.
WARNING: Always unplug the base before cleaning.
Dishwasher: Accessories are top-rack dishwasher safe and should NOT be cleaned
with a heated dry cycle. Ensure the blade assembly is removed from the bowl
before placing in the dishwasher. Exercise care when handling blade assemblies.
Hand-washing: Wash bowl, lid, disc, and blade assemblies in warm, soapy water.
Exercise care when washing the blade assemblies. Use a dishwashing utensil with
a handle to avoid direct hand contact with blades. Rinse and air-dry thoroughly.
CLEANING