Noble House Home Furnishings ROCKING CHAIR User manual

Caution : You must read this before you proceed
ROCKING CHAIR
Noble House Home Furnishings LLC Page 1 OF 9

Label Picture Description QTY
A Left Arm Panel 1
B Right Arm Panel 1
C Back 1
D Seat 1
Label Picture Description QTY
①Bolt (M8*60MM) 4
②Bolt (M8*50MM) 9
③Spring Washer 13
④Washer(18MM) 13
⑤Allen Key 1
Noble House Home Furnishings LLC Page 2 OF 9

Before
Beginning
Assembly:
Overview
Seat (D)
Back (C)
Left Arm Panel (A)
Front Facing
Right Arm Panel (B)
Noble House Home Furnishings LLC Page 3 OF 9

Step 1
This Rocking Chair has multiple parts and may require up to 30
minutes to assemble. To give you an overview of the Rocking
Chair parts, the above picture is to help you put the various parts
into perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
Place the Left Arm Panel(A), Right Arm Panel(B), Back(C) and
Seat(D) on a clean, non-marring surface.
Carefully peel away the Dust Cover from the edge of the
Seat(D).
Friendly Note:need to safekeeping the Dust Cover.
Back(C)
Seat(D)
Left Arm Panel(A)
Right Arm Panel(B)
Noble House Home Furnishings LLC Page 4 OF 9

Step 2
Put the Chair back(C) onto table.
Align the mounting positions of the Back(C) with Seat(D) and
attach them using Bolts(①), Spring Washers(③) and Washers(④)
with Allen Key(⑤).
Do not fully tighten the Bolts.
Seat (D)
Back (C)
Table
Noble House Home Furnishings LLC Page 5 OF 9

Step 3
Position the assembled Seat(D) and Back(C) onto the Right Arm
Panel(B) as shown in the picture.
Attach Seat(D) to Right Arm Panel(B) using Bolts(②), Spring
Washers(③) and Washers(④) with Allen Key(⑤).
Note: If the mounting positions cannot be aligned well and hinder
installation, then sway the Seat(D) lightly when locking the Bolts,
this action should help prevent the Bolts from getting stuck and
ensure smooth assembly.
Do not fully tighten the Bolts.
Right Arm Panel(B)
Seat(D)
Back(C)
②
③
④
⑤
Noble House Home Furnishings LLC Page 6 OF 9

Step 4
Turn the assembly over as pictured.
Attach Right Arm Panel(B) to Back(C) using Bolts(②), Spring
Washers(③) and Washers(④) with Allen Key(⑤).
Do not fully tighten the Bolts.
Repeat the same process with the Left Arm Panel(A)
Repeat the same assembly process from Step 3 and Step 4 with
the Left Arm Panel(A).
Right Arm Panel(B)
Back(C)
Seat(D)
⑤
②
③
④
Noble House Home Furnishings LLC Page 7 OF 9

Step 5
Step 6
Your Rocking Chair is ready for use.
This Rocking Chair can only be used on a flat, level surface.
Stand the Rocking Chair up, and place on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and carefully, sit into the Rocking Chair.
This will help to align all the parts at all the joints.
Tighten all Bolts fully in a sequential manner.
Then smooth down the Dust Cover on the Seat bottom with your
hands on all four edges.
Test for Stability
Left Arm Panel(A)
Back(C)
Seat(D)
Right Arm Panel(B)
Noble House Home Furnishings LLC Page 8 OF 9

Noble House Home Furnishings LLC Page 1 OF 1