Noble House Home Furnishings LIFT TOP WRITING DESK User manual

WARNING!!
Furniture Tipping Risk.
Serious risk of severe or fatal crush injuries can occur from
furniture tipping over if it's not secured.
Children like to climb on furniture and Unsecured furniture can
pose a serious danger.
Please follow all instructions and install the tip-over restraints
provided.
In addition to installing the restraints, to help prevent a tip-over:
1. Unless specifically designed for accommodating, do not set
TV’s or other heavy objects on top of this product.
2. Never allow children to climb or hang on top of the panel.
3. Do not step on the Table base.
Noble House Home Furnishings LLC Page 1 OF 12

Label Picture Description QTY
ADesk Top 1
BLeft Front Leg 1
Caution : You should read this carefully before proceeding
Please look in the Left Cornor of the carton for hardware packs
LIFT TOP WRITING DESK
Picture
Noble House Home Furnishings LLC Page 2 OF 12

CRight Front Leg 1
DHind Leg 2
E Connecting Rod 2
F Connecting Rod 1
Label Picture Description QTY
①Long Bolt
(M8*50MM)9
②Spring Washer
(∅1/4") 9
③
Flat Washer
(∅1/4"x16mm)
9
④Allen Key 1
⑤Screw
(M8x38mm) 7
Noble House Home Furnishings LLC Page 3 OF 12

⑥
Screwdriver
(not provided)
1
⑦
Power Drill
(not provided)
1
⑧Bracket 4
⑨
Wall Plug Screw
(M6X25mm)
4
⑩screw
(M8x15mm) 4
⑪
Wall Plug
(10X30mm)
4
⑫Restraint Strap 2
⑬
Hammer
(not provided)
1
Before
Beginnin
g
Assembl
y:
Noble House Home Furnishings LLC Page 4 OF 12

Overview
This Desk has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Desk parts, the above
picture is provided to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.
Desk Top
Noble House Home Furnishings LLC Page 5 OF 12

Step 1
Step 2
Please place the product on a platform.
Lift up on the top of the Writing Desk to open, then take out the inner
carton.
Attach the Desk Legs(C) to the Desk Top(A) using Bolts(①), Spring
Washers(②), Washers(③) and the Allen Key(④).
Do not fully tighten the Bolts at this time.
Noble House Home Furnishings LLC Page 6 OF 12

Step 3
Place the Desk Top(A) facedown onto a clean, non-marring surface.
3.1 Connect the Rods (E)and(F) to the Table Front Legs
(B)and(C)and the Hind Legs(D) using screws (⑤) and a
Screwdriver(⑥)
3.2) Insert the Connecting Rods(E)and(F) to the Hind Legs(D) using
screws (⑤) and a Screwdriver(⑥)
Tighten all Screws and Bolts at all joints in a sequential manner.
Noble House Home Furnishings LLC Page 7 OF 12

Flip the Desk and place it like in the diagram.
CAUTION 1: When tightening these bolts, tighten sequentially.If
there is still wobbles, loosen the bolts and execute this same
process.
WARNING!! IF DESK IS NOT STABLE , IT COULD LEAD TO
DAMAGING THE PRODUCT.Ensure all screws are fully locked into
position.
The desk is ready to be used.
Caution 2: This desk can only be used on a flat, level surface.
Console Restraint Device Installation Instructions
Serious or fatal crushing injuries can occur from tipping
furniture.
To help prevent tip-over: ALWAYS secure this furniture to the
wall using a Cabinet Restraint Device.
See product instructions for more ways to help prevent furniture
tip-over.
Step 4
Noble House Home Furnishings LLC Page 8 OF 12

Usage For Console Restraint Device:
To secure Console against wall, attach two Brackets (⑧) on the wall
and the product, use Restraint Straps (⑫) to connect the Brackets
(⑧).
Noble House Home Furnishings LLC Page 9 OF 12

Step 5
5.1)Drill two holes in the wall with a power drill ⑦.
You can mark these points in two ways as mentioned below:
1) Move the Desk back to the wall. Mark two points on the wall that
are at the same height as the desk .
Note: The Brackets need to be secured to a solid, load bearing
surface. Please use a Stud Finder(not supplied) if needed to locate
the Wall Frame.
2) Measure the height of the Brackets (⑧) with a ruler/measuring
tape and mark on the wall to keep them accurate and at the same
height.
5.2) Insert Wall Plugs (⑪) into the drilled holes on the wall with a
Hammer (⑬).Attach Brackets (⑧) to Wall Plugs (⑪) using Wall Plug
Screws (⑨) with Screwdriver (⑥).
Step
6
Noble House Home Furnishings LLC Page 10 OF 12

Step 7
The last step
Pull the Restraint Straps (⑫) through the Brackets (⑧) on the
wall and the desk one by one, and pull the Restraint Straps (⑫)
tight.
This Writing Desk is now ready to use.
Caution: This Writing Desk can only be used on flat, level
surface.
Use a Screwdriver (⑥) to lock the Bracket (⑧) with screws(⑩)to the
back of the desk.
Note: Measure the height of the Brackets (⑧) with a ruler/measuring
tape and mark on wall to keep them accurate and at the same
height.
Noble House Home Furnishings LLC Page 11 OF 12

●Children should not climb or jump on the furniture.
●Dust and pick-up spills using a clean, non-colored,
lint-free cloth.
●Do not place furniture near heating or cooling vents.
●Do not write on furniture without a padded barrier to
protect the surface.
●Do not place furniture outside . For indoor use only.
●Not for commercial use. For residential use only.
●Stains may be removed with mild soap solution and
damp cloth.
●Do not clean furniture with harsh cleansers or polish.
●Furniture may scratch floors. We recommend using
furniture pads to protect your floors.
Care & Maintenance
●Do not put hot items directly on furniture surface.
●Do not place furniture under direct sunlight.
Noble House Home Furnishings LLC Page 12 OF 12