Noctua NM-i17-MP83 Series User manual

Dear customer,
Thank you very much for choosing a Noctua cooler for your
Intel LGA1700 (LGA17xx family) system.
We always like to think of our coolers as safe long-term
investments: Not only are they built to last, but we also
provide upgrade kits so that you can keep using your trusty
Noctua heatsink whenever you do a system upgrade.
Enjoy your Noctua cooler on LGA17xx!
Yours sincerely,
Roland Mossig, Noctua CEO
This manual will guide you through the installation process step
by step using an NH-U12P heatsink as an example. Please
note that the installation procedure is identical for all models.
Prior to installing the cooler, please consult the compatibility
centre on our website (ncc.noctua.at) and verify that the cooler
is fully compatible with your motherboard.
Please also make sure that your PC case offers sufcient
clearance for the cooler and that there are no compatibility
issues with any other components (e.g. tall RAM modules).
Double check that the heatsink and fan clips do not make
contact with the VGA card, other PCIe cards, motherboard
heatsinks or any other components.
Noctua cannot be held responsible for any damage or losses
caused by compatibility issues.
Should you encounter any difculties, please check the FAQs
on our website (www.noctua.at/faqs) and don’t hesitate to
contact our support team at: [e-mail]
Multilingual versions of this manual are available on our
website: www.noctua.at/manuals
NOCTUA NM-i17xx-MP83
INSTALLATION MANUAL
Scan this code to display multilingual manuals on your phone.
Attaching the backplate2
Caution: The supplied backplate will install over the mother-
board’s stock backplate, so the motherboard’s stock back-
plate must not be taken off.
Place the NM-IBP5 backplate on the rear side of the mother-
board so that the bolts protrude through the mounting holes.
If you would like to use the cooler on an assembled system and
your case does not have a cut-out at the rear side of the mother-
board tray, you must rst remove the motherboard from the case
in order to be able to install the supplied backplate.
Removing the backplate1
Caution: Choose the alignment of the mounting bars according
to the desired nal orientation of the cooler:
Orientation A Orientation B
Caution: Make sure that the curved sides of the mounting bars
are pointing outwards.
Put the plastic spacers onto the bolts of the backplate, then add
the mounting bars.
Installing the mounting bars3
Required mounting parts:
4x NM-IPS3
blue plastic spacers
4x NM-ITS1
thumb screws
1x NM-IBP5
backplate
2x NM-IMB4
mounting bars
Please note that this NM-i17xx-MP83 kit is compatible with
heatsinks with 83mm mounting pitch (see list below) only.
For heatsinks with 78mm mounting pitch (see list below), the
NM-i17xx-MP78 kit must be used instead.
To nd out how to determine if your cooler uses 83mm or
78mm mounting pitch, please see:
www.noctua.at/mounting-pitch
For detailed, up-to-date socket compatibility information
please visit: ncc.noctua.at/socket-compatibility-overview
NM-i17xx-MP83 (83mm mounting pitch)!
NH-D15 (SE-AM4, chromax.black)
NH-D15S (chromax.black)
NH-D14 (SE2011)
NH-D9L
NH-C14
NH-C14S
NH-C12P (SE14)
NH-L12
NH-U12
NH-U12F
NH-U12P (SE1366, SE2)
NH-U9
NH-U9F
NH-U9B (SE2)
NH-L9x65 (SE-AM4)
NH-P1
NM-i17xx-MP78 (78mm mounting pitch)!
NH-L12 Ghost S1 Edition
NH-L12S
NH-U9S (chromax.black)
NH-U12A (chromax.black)
NH-U12S (SE-AM4, chromax.black)
NH-U12S redux
NH-U14S

NOCTUA NM-i17xx-MP83
INSTALLATION MANUAL
Scan this code to display multilingual manuals on your phone.
Caution: Gently tighten the screws until they stop, but do not
use excessive force (max. torque 0.6 Nm).
Caution: Note that depending on the cooler model, it may be
necessary to remove the fan(s) in order to reach the mount-
ing screws. If you’re using the cooler for the rst time, please
also take off the protection cover at the bottom side of the
heatsink rst!
Then put the heatsink onto the CPU and screw it to the screw
threads of the mounting bars. Perform 2-3 turns on each
screw, then repeat until both are fully tightened.
Fastening the heatsink to the CPU
5
If there are residual traces of thermal paste or thermal pads on
your CPU, please clean them off rst. Then apply 5 small dots
of thermal paste (e.g. Noctua NT-H1 or NT-H2) onto the CPU
(4 dots with ~2mm diameter near the corners plus 1 dot with
3-4mm diameter in the centre) as shown below:
Applying the thermal paste4
Caution: Applying too much thermal paste will lower heat
conductivity and cooling performance!
Reattach the fan(s) to the heatsink (if removed during the
installation process) and connect the fan(s) to the motherboard
as described in the cooler manual.
If you don’t have it at hand, you can download it at:
www.noctua.at/manuals
Fan setup6
!
Even with high-grade products and strict quality control, the
possibility of defects cannot be eliminated entirely. Therefore,
we aim at providing the highest possible level of reliability and
convenience by offering a warranty period of 6 years and
direct, fast and straightforward RMA service.
Should you encounter any problems with your NM-i17xx-
MP83, please don’t hesitate to contact our support team at:
[email protected]
Please also consult the FAQ section on our website:
www.noctua.at/faqs
Warranty, support and FAQs
As it is not possible to reliably calculate or control the forces
that act upon a system during transport (e.g. in shipping), we
generally recommend, for safety reasons, taking off coolers
with a total weight of more than 700g (incl. fan).
If the weight of the heatsink without fan is below 700g and
the total weight including fan is above 700g, we recommend
taking off the fan from the heatsink in order to reduce the
weight below 700g.
Noctua cannot be held responsible for any damage that may
arise due to excessive stress during transport if you keep the
heatsink installed.
Transporting your system!
Fix the mounting bars using the four NM-ITS1 thumb screws.
Caution: Gently tighten the screws until they stop, but do not
use excessive force (max. torque 0.6 Nm).