Nokeval PME600 User manual

No 100211 v1.2
User Guide
Panel meter
models PME600 & PME610
Nokeval

Overview
Panelmeter PME600/PME610 is easy to use. Operatin voltage is 21..265 VAC/DC. Meter supports common
temperature sensors thermocouple K, Pt100 and process signals 0..20 mA, 4..20 mA and 0..10 V. Meters
settings menu structure is simple, so its easy to setup.
Model PME610 contains analog output 4..20 mA. Model PME600 contains 12V output for 2-wire transmitter.
Technical information
Sensor break in tcK or Pt100, appears hyphens (---) in the display and high alarm closing and low alarm
opening.
Prosess inputs: 0..20 mA, 4..20 mA and
0..10 V
Display scaling: -999...9999
Resistance 4..20 mA: 70 Ω
shunt resistor is active only
when power is on and
device is set to mA input
Resistance 0..10 V: 110 kΩ
RTD: Pt100
Range: -200....+700°C
Current: 0,3 mA
Thermocouple: K
Range: -150.... 1350°C
mV-input: -70...70 mV
Analog output (PME610):
4..20 mA
max. load: 650 Ω
Scale: Adjustable.
Galvanic isolation
from inputs: No
Output for 2-wire transmitter (PME600):
12 V, 23 mA
Alarms: High and Low alarm.
Alarm reset: Automatic or manual via
front panel key
Hysteresis: Adjustable. Shared with
high and low alarm.
Relays: 2. One for high alarm, one
for low alarm.
Closing contact
Relays direction: Normal open
Contact Rating: 3 A, 250 VAC / 30 VDC
(res. Load)
Indication lights: In front panel
General features
Input filter: Three samples continues
average
Speed: mV, V & mA:
~ 8,3 samples / sec
Pt100 & TcK:
~ 3,4 samples / sec
AD-converter: 24 bits
Indication lights: Alarms, setup mode
Display: 4-digits bright red LED
digit height 14,5 mm
Operating voltage: 21-265 VAC/DC
IP Protection class
for front panel: IP65 with gasget
Weight: 146 g

INSTALLING
This chapter guide to install 1/8 DIN-size panelmeter PME600/PME610.
Panel installation
Panelmeter should be mount to panel cutoff according to below picture. Attach the meter with two holders
supplied.
Dimensions
Wirings
Meter has three or four (depending the model) removable screw connector. One green 6-pin connector for
input and one green 2-pin connector for mA output (PME610). One grey 4-pin connector for relays and one
grey 3-pin connector for power supply. Green connector may used only with safety extra-low voltage. Analog
output is not galvanic isolated from input. Shunt resistor for current input is internally connected only when
power is on and input sersor is set to 0-20 mA or 4-20 mA.
Operating voltage
Connect power supply to pins D1 and D3. No polarity. No ground needed. The meter has internal pre-fuse. If
an external is used, it should be at least 500mAT.
1 2 3 4 5 6 1 2
-
-
+
+
+-
4-w
+-
OUT
1234 123
Lo Alarm Hi Alarm Power
mA
V
mV
Pt100
A C DB
2w
+
96 65
48
6 10
Gasget (IP65)
Cutoff
43,7 (H) x 90,7 (W) mm ±0,7 mm
PME610:
4..20 mA
or
PME600:
12 V
(PME600)

USER INTERFACE
Front panel
There is two modes:
•Normal mode – Shows reading.
•Setting mode – For changing the settings.
After switching the power on, the userinterface is in
normal state, indicating readings.
Indicator LEDs A1 (low alarm) and A2 (high alarm)
indicate the state of alarms. Conf LED is lighting
when user interface is in setting mode.
Manual reset with front panel v-key can be
selected by choosing wider hysteresis than full
span.
Setting mode
Entering
In the normal mode press *- and ^-buttons
simultaneously until conf LED start lighting.
Navigating
Within menu you can navigate up and down using
the ^v-buttons.
Editing
Pressing the >-button shows the value of the
settings and allows editing it.
Most data types are edited simply with
^v-buttons and exited with *-button.
Floating point numbers are edited using the
^v>-buttons. Select the digit to be edited or the
decimal point with >-button and edit it with
^v-buttons. The first digit can be edited to a minus
sign.
Exiting
When all done, exit from setting mode with
*-button. Select ^v Save (keep the changes) or
Undo (discard the changes) and press >.
Keylock
It is possible to prevent access to the setting mode by setting a jumper as shown :
Key lock off (default) Key lock on

Flow diagram
Output settings OUTL and OUTH are visible only in model PME610.
Auto reset is a standard function. Manual reset with front panel v-key can be selected by
choosing wider hysteresis than full span (Hi -Lo). For example: Input scaling is 0..100,0 i.e.
full span is 100. Select hysteresis larger than 100 (9999) and you will have manual reset.
Display scaling for V- and mA-inputs:
Reading when input is in min. level.
High alarm level
Input selection
4-20 = 4...20 mA
0-20 = 0...20 mA
Pt 3 = Pt100 3-wire
Pt 4 = Pt100 4-wire
Tc = Thermocouple K
mV = Millivolts
0-10 = 0...10 V
AL L
AL H
HYST
BRI
DEC
SENS
IN L
IN H
OUTL
OUTH
-999...9999
-999...9999
-999...9999
-999...9999
-999...9999
-999...9999
0...9999
1...6
-3...3
4-20
*
*
*
0-20
Pt 3
Pt 4
Tc
mV
0-10
*
*
*
*
**
*
*
SAVE
UNDO
*+
Output scaling: Display reading
corresponding 20 mA output.
Hysteresis level
Output scaling: Display reading
corresponding 4 mA output.
Low alarm level
Display scaling for V- and mA-inputs:
Reading when input is in max. level.
Display brightness
Positive value: decimals.
Negative value: rounding to zero