Nokia Lumia 930 RM-1045 User manual

Send feedback
Recommend Change in
KICS
Rate this page in KICS
E-mail
[email protected]
Service Manual for L1 and L2
Nokia Lumia 930
RM-1045
Key features

2.2 GHz Quad core processor

5" Full-HD OLED Display

32 GB Internal memory

20 MP Nokia PureView camera

Integrated wireless charging
Version 1.0
CHECK THE REPAIR
POLICY BEFORE
PERFORMING ANY
MECHANICAL REPAIR ON
SERVICE LEVEL 1&2!
Exploded view Disassembly steps
Assembly hints Solder components Service devices
Product controls and interfaces Service concept Phone reset
More More
More More More
More More More
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

Service Manual Level 1 an
d
2
Nokia Lumia 930
RM-1045
V
ersion 1.
0
Version histor
y
Version Date Description
1.0 29.05.2014 First published version
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia Lumia 930
RM-1045
Version 1.0
Exploded view
CHASSIS
I0004
HSJ ASSEMBLY
I0036
HSJ GASKET
I0037
JUMPER FLEX
I0026
MAIN ANTENNA LTE
COAX FLEX
I0005
VIBRA ASSEMBLY
I0019
DAUGHTER PWB GASKET
I0016
VIBRA BOOT
I0021
SIM TRAY
I0001
SKYPE CAMERA ASSEMBLY
I0017
EARPIECE
I0022
EARPIECE GASKET
I0015
JUMPER FLEX ADHESIVE
I0027
LABEL TRAY
I0024
WATER INGRESS LABEL
I0025
DAUGHTER PWB
I0035
LTE ADHESIVE
I0031
LIGHT SWAP PWB
I0038
LTE RF COAX CABLE
I0030
TYPE LABEL
I0040
SKYPE CAMERA WINDOW GASKET
I0018
CAMERA KEY
I0007
LOCK KEY
I0008
VOLUME KEY
I0009
SMALL BATTERY ADHESIVE
I0011
VIBRA FLEX ADHESIVE
I0020
PRIMARY MIC FLEX
I0012
PRIMARY MIC GASKET
I0013
MIMO COAX FLEX
I0028
BATTERY
I0032
HEAT SPREADER
I0039
BATTERY CONNECTOR STRAP
I0033
MIMO COAX FLEX ADHESIVE
I0029
CAMERA
I0023
BATTERY ADHESIVE
I0010
PRIMARY MIC FLEX
ADHESIVE
I0014
DISPLAY WINDOW
I0002
DISPLAY
I0003
MAIN ANTENNA VOICE
COAX FLEX
I0006
LIGHT SWAP PACKAGE
(I0038 - I0040)
2
CARE UI ASSEMBLY
(I0002 - I0016) 1
Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
1/2
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

SCREW TORX+ SIZE 4
M1.4 X 3.8
I0034
GPS/WLAN ANTENNA
I0042
LED FLASH
I0049
NFC ANTENNA
I0051
BACK COVER GASKET
I0048
FLASH ADHESIVE
I0047
MIMO ANTENNA
I0043
IHF SPEAKER ASSEMBLY
I0041
MAIN ANTENNA LTE
I0044
MAIN ANTENNA VOICE
I0045
WIRELESS CHARGING
ASSEMBLY
I0050
BACK COVER
I0046
ENGINE COVER ASSEMBLY
(I0041 - I0045)
3
BACK COVER ASSEMBLY
(I0046 - I0048)
4
Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
2/2
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia Lumia 93
0
R
M
-1045
Version 1.0
Disassembly steps
1) For disassembling you need the Nokia Standard toolkit version 2. You will also need the SS-311 back
cover release tool, the SS-319 RF-connector disassembly/assembly tool and an AV jack.
Note that the device shown in most of these pictures is the Nokia Lumia Icon. On those steps the spare
parts and the disassembly procedures are the same.
2) Protect the DISPLAY WINDOW with protective film.
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

3) Open the SIM TRAY with the SS-93 and pull it out.
4) At this point, if you only want to check the TYPE LABEL without having to disassemble the phone, you
can pull the LABEL TRAY out with the hook on the SIM TRAY.
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

5) Release the BACK COVER with the SS-311 from the shown corner.
6) Remove the BACK COVER.
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

7) Unscrew the TORX+ SIZE 4 screw on top of the BATTERY CONNECTOR STRAP. Do not use the screw
again. Discard it.
8) Remove the BATTERY CONNECTOR STRAP with tweezers.
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

9) Disconnect the BATTERY connector with the SS-93. Be careful not to damage the connector.
10) Unscrew the ten TORX+ SIZE 4 screws in the order shown. Do not use the screws again. Discard them.
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.

11) Release the ENGINE COVER ASSEMBLY from the shown place with the SS-93.
12) Lift up and remove the ENGINE COVER ASSEMBLY top end first. Be careful not to damage the antenna
spring contacts on the bottom of the ENGINE COVER ASSEMBLY.
©2014 Microsoft | Microsoft Internal Use only | All Rights Reserved.